Selection Guide

ManualsBrandsSlant/Fin ManualsBaseboard Heaters4 ft. Multi/Pak 93-17 Baseboard - Cover Only (2 Tier)

350 Series

Furnish and install 350 Ser ies Model___________

baseboard cover assembly as manufactured by

Slant/Fin Corporation, consisting of one-piece bottom,

back and top panel, and one-piece 19 (16) gauge front

panel, formed of cold rolled steel. Bottom and top

edges of back panel shall be formed to provide chan-

nels along entire length, to receive full-height support

brackets.

Brackets shall be die formed of electro-galvanized

cold rolled steel, for rigid bracing and spring locking.

Slide-action expansion cradles, formed of polypropy-

lene, shall be inserted between heating element and

support bracket. Cradles shall protect element bottom

and sides from contact with brackets or cover, confining

element to free lateral expansion for noiseless opera-

tion.

Provide all required accessories for a complete

installation. Cover accessories shall be telescopic and

shall match enclosure color.

All cover components shall be painted in Nu-White,

oven baked melamine cross-linked polyester enamel.

HD Series

Furnish and install as shown on the plans model

__________ HD Series slope-top baseboard with ele-

ment, required mounting components and accessories

as manufactured by Slant/Fin Corporation. Complete

two-piece enclosure assembly shall consist of full back

panel with interlocking slope top front panel, factory

packaged with necessary brackets.

Front cover shall be fabricated from 16-gauge gal-

vanized steel, back panel from 20-gauge galvanized

steel. The front panel & accessories shall be finished in

galvanized finish or as custom color matched as per

specifications. Fin-tube element(s) shall be

Model___________. Provide lengths, heights and capac-

ities as scheduled on plans.

Bracket with element hanger shall be spot w elded

to back panel every 12 inches. There shall be dimpled

anchoring holes every 12 inches on front cover. Use 8 x

3/8" self-tapping screws with countersunk heads to fas-

ten front cover to brackets. Screws recess into dimpled

anchoring holes on front cover. Screws are supplied in

carton with cover.

Provide all required accessories for a complete

installation. Cover accessories shall be telescopic to

eliminate the need to perfectly butt one length of cover

to the next. Accessories to be fastened with screws

(pan-head) supplied by others.

LC Series

Furnish and install as shown on the plans model

(LC-850, LC-1400) LC Series-slope top baseboard with

element, required brackets and accessories as manu-

factured by Slant/Fin Corporation.

Front Cover shall be fabricated from 18-gauge galva-

nized steel. Top horizontal lip of cover shall be no wider

than 7/8 inch, this is to prevent standing on the cover.

Outlet louvers shall be located on the front sloped f ace

of the cover, louvers located on the top of the co ver are

not acceptable. Cover finish shall be galvanized finish

or custom color matched as per specification.

Front cover to be mounted on the wall with one piece

wall brackets. Brackets shall be spaced no fur ther than

2 feet apart with bracket secured to wall studs and not

to the wall board. Slide-action expansion cradles shall

be inserted between heating element and cover brack-

ets. Slide-action expansion cradles are supplied with

heating element. Installer shall secure front cover to

mounting brackets by drilling hole into vertical flange on

lower front cover and screwing front cover to each wall

bracket. Screws are field supplied.

Finned tube heating element shall be Model ______.

(One, Two) tiers of element to be installed within co ver.

Provide lengths, heights and capacities as scheduled

on plans. (Add specification for model of element being

specified)

Provide all required accessories for a complete installa-

tion. Accessories shall be telescopic to eliminate the

need to perfectly butt one length of cover to the next.

Accessories to be fastened with pan head screws to

front cover, screws are field supplied.

Multi/Pak 80

Furnish and install Multi/Pak

80 baseboard

cover assembly as manufactured by Slant/Fin Corporation,

consisting of one-piece 21-gauge back and top panel, and

one-piece 18-gauge front panel, formed of cold rolled galva-

nized steel. Bottom and top edges of back panel shall be

formed to provide channels along entire length, to receive full-

height support brackets.

Brackets shall be die formed of zinc-bonded 16-

gauge quarter-hard cold rolled steel, for rigid bracing

and spring locking. Slide-action expansion cradles,

formed of polypropylene, shall be inserted between

heating element and suppor t bracket. Cradles shall pro-

tect element bottom and sides from contact with br ack-

ets or cover, confining element to free lateral expansion

for noiseless operation. Room-control damper vane, of

quarter-hard cold rolled steel, shall be pro vided for each

length of enclosure, and shall modulate fully and freely,

yet retain any setting through its arc without protr uding

knobs or other devices. Support bracket shall be formed

to retain and suppor t damper vane without use of addi-

tional pivots. All cover components shall be painted in

Nu-White, oven baked melamine cross-linked polyester

enamel.

F & EM Series

Furnish and install as shown on the plans “F”

or “EM” Series flat-top enclosures with elements,

required mounting components and all accessories as

manufactured by Slant/Fin Corporation. Cover shall be

of one piece construction. Enclosure shall be EM-5,

EM-12, EM-19, F-5, F-12 or F-19 and shall ha ve (1,2 or

3) tier element. EM enclosure shall be made of e xpand-

ed steel. F enclosure shall consist of stamped top g rille

with pencil-proof air discharge louvers.

Covers shall be fabricated from 18-gauge (16-

gauge for EM) steel in electro galvanized finish or as

custom color matched as per specification.

Brackets and hangers shall be channeled

steel in electro galvanized finish. Fin-tube element(s)

shall be Model_________. Provide lengths and capaci-

tiies as scheduled on plans.

Furnish required channeled bracket-hanger

assemblies for rigid element support.

Provide all required accessories for complete

installation. Enclosure accessories in bonded zinc steel

shall be telescopic and match enclosure color.

C-540, C-440 and C-340 Element

Furnish and install C-540, C-440 and C-340

fin-tube heating elements as manufactured by

Slant/Fin Corporation, consisting of 1

⁄4" nominal* cop-

per seamless-drawn tubing* with 4

⁄4" x 4

⁄4"x .020" alu-

minum fins spaced 40 per linear foot. Fins shall be

mechanically bonded to the tubing to increase ther mal

contact and to space and lock the fins uniformly in

place. A flange with four teeth shall be formed on each

fin to increase thermal contact and to space and lock

the fins uniformly in place. One end of each element

shall be expanded to receive the expanded end of

another, without couplings.

* C-440 is 1" copper pipe. C-340 is

⁄4" copper pipe.

S-540, S-532 and S-832 Element

Furnish and install S-540 and S-532 fin-tube

heating element as manufactured by Slant/Fin

Corporation, consisting of 1

⁄4" IPS steel pipe*

(Schedule 40), with 4

⁄4" x 4

⁄4"x .024"steel fins spaced

40 per linear foot for S-540 and 32 per linear foot for S-

532 and S-832. The pipe shall be forced through under-

sized fin holes to obtain a force-fit mechanical bond. A

flange with four teeth shall be formed on each fin to

increase thermal contact and to space and lock the fins

uniformly in place. Both ends of each element pipe shall

be threaded with IPS standard threads.

* S-832 is 2" IPS steel pipe.

H-1 Element

Furnish and install H-1 baseboard heating

element as manufactured by Slant/Fin Corporation,

consisting of

⁄4" nominal copper tubing, with 3" x

⁄4"x .024"aluminum fins, spaced 48 per linear foot. Fins

shall be mechanically bonded to the tubing to increase

thermal contact and to space and lock the fins uniformly

in place. A flange with four teeth shall be formed on

each fin to increase thermal contact and to space and

lock the fins uniformly in place.

One end of each element tube shall be e xpanded

to receive the unexpanded end of another, without cou-

plings.

H-3 Element

Furnish and install H-3 baseboard heating

element as manufactured by Slant/Fin Corporation,

consisting of

⁄4" nominal copper tubing, with 3

⁄32" x

⁄2"x .011"aluminum fins bent to 2

⁄4"x 2

⁄2", spaced 55

per linear foot. Fins shall be mechanically bonded to the

tubing to increase thermal contact and to space and

lock the fins uniformly in place. A flange with four teeth

shall be formed on each fin to increase ther mal contact

and to space and lock the fins uniformly in place. One

end of each element tube shall be e xpanded to receive

the unexpanded end of another, without couplings.

H-4 Element

Furnish and install H-4 baseboard heating element

as manufactured by Slant/Fin Corporation, consisting of

1" nominal copper tubing, with 3

⁄32" x 2

⁄2"x .011" alu-

minum fins bent to 3"x 2

⁄2", spaced 48 per linear foot.

Fins shall be mechanically bonded to the tubing to

increase thermal contact and to space and lock the fins

uniformly in place. A flange with four teeth shall be

formed on each fin to increase ther mal contact and to

space and lock the fins uniformly in place. One end of

each element tube shall be expanded to receive the

unexpanded end of another, without couplings.

H-5X Element

Furnish and install H-5 baseboard heating

element as manufactured by Slant/Fin Corporation,

consisting of 1

⁄4" nominal copper tubing, with 3" x

⁄4"x .020" aluminum fins, spaced 48 per linear foot.

Fins shall be mechanically bonded to the tubing to

increase thermal contact and to space and lock the fins

uniformly in place. A flange with four teeth shall be

formed on each fin to increase ther mal contact and to

space and lock the fins uniformly in place. One end of

each element tube shall be expanded to receive the

unexpanded end of another, without couplings.

H-6X Element

Furnish and install H-6 baseboard heating

element as manufactured by Slant/Fin Corporation,

consisting of 1

⁄4" IPS steel pipe (Schedule 40), with 3"

x 3

⁄4"x .028" steel fins, spaced 48 per linear foot. Fins

shall be mechanically bonded to the pipe to increase

thermal contact and to space and lock the fins uniformly

in place. A flange with four teeth shall be formed on

each fin to increase thermal contact and to space and

lock the fins uniformly in place. Both ends of each ele-

ment pipe shall be threaded with IPS standard threads .

E-75E Element

Furnish and install E-75 baseboard heating

element as manufactured by Slant/Fin Corporation,

consisting of

⁄4" nominal copper tubing with 2

⁄8" x

⁄8"x .009" aluminum fins, bent to 2

⁄16"x 2

⁄8", spaced 55

per linear foot. A flange with four teeth shall be formed

on each fin to increase thermal contact and to space

and lock the fins uniformly in place. End fins are of plat-

ed steel for extra ruggedness. One end of each element

tube shall be expanded to receive the unexpanded end

of another, without couplings.