Selection Guide

23
RATINGS
WALL
TRIM
OUTSIDE
CORNER
90˚ or 135˚
INSIDE
CORNER
90˚ or 135˚
FILLER
SLEEVE
END CAP
4''
2''
4-3/4"
7" or 14"
4"
Over 20 easy-to-install accessories are available in a variety
of hinged, non-hinged, telescoping, snap-on and custom
angle models to complete any installation.
additional accessories
Splice Plate, 2"
Valve cover*, 8"
Valve cover, slotted*, 8"
Inside corner*, custom angle
Outside corner*, custom angle
Center valve cover*, 8”
Zone valve box
Back panel for inside corner
Column cover set
*Telescopic accessories
Filler Sleeve Hinged End Cap Hinged Wall Trim Hinged Valve Cover Hinged Inside Corner Outside Corner
TELESCOPIC ACCESSORIES
Model
Number
Element
Type
Tube
Size and
Material
Fin Size
and Material
Fins
per
Foot
Water
Flow
Pressure
Drop†
HOT WATER RATINGS ‡
BTU/HR./FT.
110˚F 120˚F 130˚F 140˚F 150˚F 160˚F 170˚F 180˚F 190˚F 200˚F 210˚F 220˚F
81 A H-1
3
⁄4"3 x 3
1
⁄4" x .024" 48 1 GPM 47 210* 290* 360* 440* 520 610 700 790 880 970 1060 1140
copper aluminum 4 GPM 525 220* 310* 380* 470* 550 640 740 840 930 1030 1120 1200
83-A2 H-3
3
⁄4"23⁄4" x 2
1
⁄2" x .011" 55 1 GPM 47 200* 270* 340* 410* 490 570 650 730 810 890 970 1050
copper aluminum 4 GPM 525 210* 290* 360* 430* 520 600 690 770 860 940 1030 1110
84-A3 H-4 1" 3" x 2
1
⁄2" x .011" 48 1 GPM 13 200* 260* 330* 400* 480 560 640 720 800 880 960 1040
copper aluminum 4 GPM 145 210* 270* 350* 420* 510 610 680 760 850 930 1010 1100
85-AX H-5X 1
1
⁄4" 3" x 3
1
⁄4" x .020" 48 1 GPM 6
1130
190* 260* 320* 390* 470 560 650 740 830 920 1010 1100
copper aluminum 4 GPM 63 200* 270* 340* 410* 500 590 690 780 890 970 1070 1160
86-AX H-6X 1
1
⁄4" IPS 3" x 3
1
⁄4" x .028" 48 1 GPM 3
990
410 490 560 640 710 790 860 940
steel aluminized steel 4 GPM 41 430 520 590 680 750 840 910 990
Steam
1 PSI
‡
Btu/Hr.
Per Foot
ACCESSORIES
† Millinches per foot. *Ratings at 140˚F and lower temperatures determined by multiplying 150˚F rating by the applicable factor specified in Table E in the I=B=R Testing and
Rating Standard for Baseboard radiation.
‡ With 65˚F entering air.
NOTE: Ratings are for element installed as per drawing shown in “Dimensional Data” window (open “Dimensional Data” window to view) with damper open, with expansion cradles. Ratings are
based on active finned length (5" to 6" less than o verall length)and include 15% heating effect factor.
Ratings are also based on:
81-A: 3/4" nominal copper tubing with 3" x 3-1/4' x .024" alumin um fins spaced 48 per linear foot (unpainted);
83-A2: 3/4" nominal copper tubing with 2-3/4" x 2-1/2" x .011" alumin um fins spaced 55 per linear foot (unpainted);
84-A3: 1" nominal copper tubing with 3" x 2-1/2" x .011" alumin um fins spaced 48 per linear foot (unpainted);
85-AX: 1-1/4" nominal copper tubing with 3" x 3-1/4" x .020" alumin um fins spaced 48 per linear f oot (unpainted);
86-AX: 1-1/4" IPS steel with 3" x 3-1/4" x .028" aluminiz ed steel fins spaced 48 per linear foot (unpainted);
Use 4 gpm ratings only when flow is known to be equal to or g reater than 4 gpm; otherwise, 1 gpm ratings must be used.