CA Prop 65

ManualsBrandsSlab ManualsCaulk10.5-fl oz Gray Sanded Paintable Latex Caulk

PLOTTER DIRECTION-S

NUMBER 043

SONOCO KASE LAYOUT

DATE REVISED BY DIXIE: 06-12-08

HANOVER

COPY

START

CENTER LINE

II17

DX#043

2% 25% 50% 75% 98% 100%

REORDER NO: SN-2697

PART NO: 89-3 DATE: 11-07-08

COLORS: BLACK

DIXIEGRAPHICS

SONOCO SN-2697_K043 699842 11-07-08 464/BH ILL. CS3

CENTER LINE

REORDER NO: SN-2697 PART NO: 89-3 DATE: 11-07-08 COLORS: BLACK

4400 CARTRIDGE WRAP AROUND ONLY - NO TEXT OR ART 4400 CARTRIDGE WRAP AROUND ONLY - NO TEXT OR ART

5-3/4" MAX. TEXT AND ART

6-3/16" MAX. WRAP AROUND/BLEED 4400 CARTRIDGES

1/2"

PRINT HEIGHT 7-1/2"

TUBE LENGTH 8-1/2"

1/2"

CLOSED

END

OPEN

END

UPC: 0 31525 16210 2

Prints 3 color: PMS 2627, PMS 375 & Black

Gray

10.5 FL. OZ.

(

310 mL

)

for Concrete Cracks

Sticks • Stretches • StaysSticks • Stretches • Stays

Serious Fix

The

SLB1-18

e know what you’re thinking. “Concrete repair products dry out

and crack – again. Why bother?” You’re right, they’re not what

they’re cracked up to be. You need an elastic repair that

moves when the crack moves; you need it to stick; you need it textured

like concrete; and you need easy water clean-up. You need Slab

• Paintable • Textured to blend-in with concrete

• Spans gaps up to 3” wide

Use Slab to Repair & Seal:

• Driveways & Sidewalks • Patios & Garages

• Expansion Joints • Stone, Brick, Stucco, Mortar

INSTRUCTIONS

Before You Start:

• Apply to clean surfaces

• Use on horizontal concrete surfaces that have cured at least 4 weeks

• Application range: surface temperature of 40°F to 120°F

• Skins over in 30 min.* Tack free in 2-4 hours.* Cure time 1-2 weeks.*

May attract dirt and debris until skin forms.

* Sealant skin and cure times are dependent on temperature, humidity,

and bead size.

• Keep foot and vehicle traffic off of the sealant for a minimum of 24

hours after application to give Slab sufficient time to build strength.

Note: in areas of 50% humidity or higher it is best to wait 48 hours.

• Protect from water for 24-48 hours after application

• For best results recess Slab below the surface of the crack

Step 1. Remove any previously applied caulk or foams, as well as oils,

dirt and other contaminants. Thoroughly clean the crack with either a stiff

bristled brush or a drill-mounted brush. Sweep or blow out any debris.

Step 2. For joints deeper than ½”, install Sashco

Filler Rope™ (see diagram).

Step 3. Cut nozzle to the desired bead size.

Step 4. Gun Slab into the crack.

Step 5. Press Slab into the sides of the crack for

best adhesion. Smooth out using water and a foam

brush or finger, etc. For best results, recess Slab

below the surface of the crack.

CLEAN UP & STORAGE

Clean up any fresh product on surfaces and skin with soap and water.

Tightly reseal cartridges with plastic wrap and a rubber band. Store

between 40°F and 90°F.

CAUTION:

Avoid contact with eyes and skin. Do not swallow. In case

of eye or skin contact, flush thoroughly with water. If swallowed, do not

induce vomiting. Call physician immediately. KEEP OUT OF REACH

OF CHILDREN.

WARNING: Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

VOC: 58 g/L, <1.5% by weight.

LIMITED LIFETIME WARRANTY: For a detailed description of the

warranty and exclusions, please visit our website

at www.sashco.com.

0 3 1 5 2 5 1 6 2 1 0 2

10300 E. 107th Place

Brighton, CO 80601

800-767-5656

www.sashco.com

Made in the USA