User Manual

PRODUCT SPECIFICATION
MODE: TX-5D
5.8G 600mW 32 Channel HDMI to
AV Transmitter Module
Modulate Wideband FM Modulate
Video Format NTSC/PAL
Characteristics
Value Units
Min. Typ. Max.
1 Output Impedance --- 50 --- Ohm
2 Output Power 26.5 27.5 28 dBm
3
Frequency
range
Channel
Frequency
FR1 or (A)
CH1 --- 5865 --- MHz
CH2 --- 5845 --- MHz
CH3 --- 5825 --- MHz
CH4 --- 5805 --- MHz
CH5 --- 5785 --- MHz
CH6 --- 5765 --- MHz
CH7 --- 5745 --- MHz
CH8 --- 5725 --- MHz
FR2 or (B)
CH1 --- 5733 --- MHz
CH2 --- 5752 --- MHz
CH3 --- 5771 --- MHz
CH4 --- 5790 --- MHz
CH5 --- 5809 --- MHz
CH6 --- 5828 --- MHz
CH7 --- 5847 --- MHz
CH8 --- 5866 --- MHz
3
FR3 or (E)
CH1 --- 5707 --- MHz
CH2 --- 5685 --- MHz
CH3 --- 5665 --- MHz
CH4 --- 5645 --- MHz
CH5 --- 5885 --- MHz
CH6 --- 5905 --- MHz
CH7 --- 5925 --- MHz
CH8 --- 5945 --- MHz
FR4 or (F)
CH1 --- 5740 --- MHz
CH2 --- 5760 --- MHz
CH3 --- 5780 --- MHz
CH4 --- 5800 --- MHz
CH5 --- 5820 --- MHz
CH6 --- 5840 --- MHz
CH7 --- 5860 --- MHz
CH8 --- 5880 --- MHz
4 Operating Voltage 7.0 12 24 V
5 Supply current --- 250 --- mA
6 Operating Temperature -10 --- +85
o
C
7 Video Band Width 0 --- 8.0 MHz
8 Audio carrier Frequency --- 6.5 --- MHz
9 Video Input Level 0.8 1.0 1.2 Vp-p
10 Video Input Impedance --- 75 --- Ohm
11 HDMI Input
720 x 576
px
720 x 480
12 Audio Input Level 0.5 --- 2.0 Vp-p
13 Audio Input Impedance --- 10K --- Ohm
14 Weight --- 28 --- g
15 Antenna Connector RPSMA Connector
16 Dimensions (L x W x H) 54x32x26.5mm
CH
FR
CH
CH1 CH2 CH3 CH4
FR
FR1
5865M 5845M 5825M 5805M
FR2
5733M 5752M 5771M 5790M
FR3
5705M 5685M 5665M 5645M
FR4
5740M 5760M 5780M 5800M
CH
FR
CH
CH5 CH6 CH7 CH8
FR
FR1
5785M 5765M 5745M 5725M
FR2
5809M 5828M 5847M 5866M
FR3
5885M 5905M 5925M 5945M
FR4
5820M 5840M 5860M 5880M
Application examples:
1. When video input switch turns to HDMI, the gear is in
HDMI input function. Can connect HDMI output device,
and turn the HDMI signal into CVBS before sending.
2. When video input switch turns to CAM, the gear is in
CVBS input function.
Can send the output CVBS signal from camera directly.
3. When gear is connected with aircraft remote control
by PPM line, it can switch channel in the air.
4. When work with RC800, you can connect RC800
with remote control to achieve channel sync
adjustment.
Note: functions 3-4 can work on futaba remote control.
Warning: please install the antenna of
transmitter before power on.