9 /20 LCD Television / Monitor Owner s Manual SLTV-1963A SLTV-2063A
The lighting flash with arrow head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
11.POLARIZATION - This unit is equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still fails to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 12.
TABLE OF CONTENTS Table of Contents Congratulations Specifications Installation Television Location Remote Control Battery Installation Power Source Combination VHF/UHF Antenna Optional Equipment Connections Rear Panel Connectors Front Control Panel Remote Control Operation TV mode 4 4 5 5 5 5 6 7 7 7 8-11 8-11 Function Menu Operation PICTURE V-CHIP Setup menu DTV Setting menu Tune menu PC Setup menu Special Message Service Tips Limited Warranty 12-16 12 12 13 14 14 15 16 17 18-19 3
¼ò ½é CONGRATULATIONS Congratulations Your new TV Monitor/Receiver features a solid state chassis that is designed to give you many years of enjoyment. It was thoroughly tested and tuned at the factory for best performance. 19 19 Color (Diagonal) 408.24 x 255.15mm (H x V) 1440 x 900 20 20 Color (Diagonal) 433.61 x 249.
INSTALLATION Installation Television Location Follow these recommendations before deciding the location of your television. Avoid excessive sunlight or bright lights, including reflections. Keep away from excessive heat or moisture. Inadequate ventilation may cause internal component failure. Fluorescent lighting may reduce remote control transmitting range. Keep away from magnetic equipment, including motors, fans and external speakers.
INSTALLATION Combination VHF/UHF Antenna Combination VHF/UHF Antenna (Single 75 ohm cable or 300 ohm twin-lead wire) Connect the 75 ohm cable from a combination VHF/UHF antenna to the antenna jack. Combination VHF/UHF Antenna (Separate VHF and UHF 300 ohm twin-lead) Connect the UHF twin-lead wire to a combiner (not supplied). Connect the VHF twin-lead to the 300-75 ohm matching transformer (not supplied). Attach the transformer to the combiner. Attach the combiner to the antenna jack.
BASIC CONTROLS AND CONNECTIONS Optional Equipment Connections Front Control Panel The front control panel can be used to access menus and switch video mode when the remote control is not available. Side Panel Connectors AUDIO IN 1 ANT IN 1 VIDEO R L 2 3 COMPONENT S-VIDEO Y 4 5 Pb AUDIO IN 2 Pr 6 PC IN R L 7 8 9 AUDIO OUT HEADPHONE 10 R L 11 12 1. Antenna or cable In 2. Video / S-Video Audio Right In 3. Video / S-Video Audio Left In 4. Video In 5. S-Video In 6. Component In 7.
»ù±¾²Ù×÷ REMOTE CONTROL OPERATION Remote Control Operation -/-- POWER -/-- Turn on / off. MUTE 2 3 4 5 6 7 8 9 - /- - 0 Q. VIEW Select channel digits. Q.VIEW Q.VIEW Mute the sound. Back to previous viewed channel. TV/AV DTV CC CH.+ SLEEP DTV Enter DTV Setting menu VOL.- MENU VOL.+ Set the sleep timer. CH.- P.M P.M Select desired picture mode. I/II AUDIO P.M. DTV I/II Display information of current input. I/II Select sound mode. MENU CC Display menu function.
REMOTE CONTROL OPERATION TV MODE: 1.POWER Button( ) Press this button to turn the TV on or off. 2 1 2. Mute Button( ) Press once to mute the sound, press again to recover previously set sound level. This button will not work if CC display is switched on. DTV:Press this button to enter DTV setting menu. 3. Picture Mode Button( P.M ) 2 3 4 5 6 7 8 9 8 - /- - 0 Q. VIEW 9 CUSTOM RICH 6 TV/AV CC 5 SOFT STANDARD 7 CH.+ 13 VOL.- 14 MENU VOL.+ 3 10 P.M. DTV I/II 4.
REMOTE CONTROL OPERATION To quit this menu please press CC button again or MENU button or it will disappear automatically after 10-second display. 6.TV/AV Button( TV/AV ) 2 1 2 3 4 5 6 7 8 9 0 Q. VIEW 9 CC 5 8 - /- - 6 TV/AV 7 7.Number (0-9) Button CH.+ 13 VOL.- 14 MENU VOL.+ 12 10 P.M. DTV Press these buttons to enter digits. These buttons for direct access to use a channel to enter channel number for both ATV and DTV or enter password for V-Chip. 8.
REMOTE CONTROL OPERATION 11.Recall Button( 2 1 2 3 4 5 6 7 8 9 8 - /- - 0 Q. VIEW 9 6 TV/AV CC 5 ) Press this button to display information on current input. 12.Menu Button 7 Press this button to enter Picture menu or quit from current menu. 13.Channel Up(CH.+) / Down( CH.-) Button CH.+ 14.Volume Up(VOL.+) / Down(VOL.-) Button 13 VOL.- 14 MENU Press these buttons to select channels in ascending or descending order for both ATV and DTV or select available items in a menu. VOL.
Function Menu Operation Function Menu Operation Press CH- button to enter V-Chip menu if there is no password or enter Password Check menu CH.+ VOL.- MENU VOL.+ CH.- Press MENU button to display Picture menu. You can browse Picture, V-Chip, Setup, Tune and PC Setup menu by pressing VOL+/VOL- buttons. Press CHbutton to enter the selected menu and adjust available settings by pressing VOL+/VOL- buttons or confirm you selection or enter next menu by pressing VOL+ button.
Function Menu Operation Function Menu Operation MPAA Rating Press VOL+ button to enter MPAA Rating menu Input your password, press VOL+ to confirm. If the password is correct, image and volume will recover. Otherwise image and volume will still be blocked and above dialog will not disappear. In this menu you can set MPAA rating. Press CH+/CH- buttons to select desired rating, block or unblock the selected rating by pressing CH+/CH- buttons.
Function Menu Operation Function Menu Operation DTV Setting menu Factory Reset Press VOL+ button to reset DTV settings with default value. Note: It is strongly recommended that you should scan DTV programs right after reset DTV settings. Otherwise you can not watch all DTV programs. DTV related functions can be reached in this menu. Antenna level Press VOL+ button to enter DTV Antenna level menu.
Function Menu Operation Function Menu Operation TV Source Press VOL+ button to enter TV Source menu. In TV Source menu, you can switch TV source among Antenna, Cable(STD), Cable(IRC) and Cable(HRC) by pressing VOL+ button. Please make it sure that proper TV Source is selected before auto scan is started otherwise programs may not be found and stored. Skip Press VOL+/VOL- buttons to switch on or switch off the skip function.
Function Menu Operation Function Menu Operation Auto Configuration Special Message: No Signal This message indicates that PC automatic configuration is in process. After finish PC image adjustment, this message will disappear. This message indicates there is no signal for PC input. If there is no signal for PC input, black screen will be displayed and above dialog mentions you to plug PC signal. For all inputs other than PC input, blue screen will be displayed if there is no valid input.
»ù±¾²Ù×÷ Service Tips Service Tips Symptoms Possib le Remed ies Try diffe rent ch annel, Check if OK, p aerial c robably o nnectio station Check ns on b aerial fo trouble ack of r broke set Re-orie n w ir nt aeria es l (if ind Pr o b a b oor typ ly local e) interfer Adjust ence, s fine tun uc h a s ing con an app Adjust trol liance brightn ess co Adjust n tr o l contras t contro Check l if statio n is broa Adjust dcastin colour g colou control Check r if syste m is Check correctl if on/off y set switc
18
Skyworth Electronics Inc. 1312 John Reed Court, City of Industry, CA 91745 Phone: 626-336-3698 Fax: 626-336-3238 Email: service@skyworth.com.hk Http: www.skyworth.com.
