Parts Manual Instruction Manual

DRIVE TRAIN
31200732 8042/10042/10054 5-3
Figure 5-1 Drive Train Components
Item Part Number Qty. Description Rev.
1001104796 Ref AXLE INSTALLATION, (8042), (not available to order, see items 1 thru 9 for
service)
C
1001104800 Ref AXLE INSTALLATION, (10042 & 10054), (not available to order, see items 2 thru
10 for service)
D
1 Ref FRONT AXLE, (see Figure 5-2 for details)
2 Ref REAR AXLE, (see Figure 5-10 for details)
3 3423254 2 AXLE PIVOT PIN, (8042)
3423254 1 AXLE PIVOT PIN, (10042 & 10054)
4 0642640 2 HEX HD CAPSCREW, 1-8X5, GR5, (8042)
0642640 1 HEX HD CAPSCREW, 1-8X5, GR5, (10042 & 10054)
5 8310116 2 HEX LOCKNUT, 1-8, (8042)
8310116 1 HEX LOCKNUT, 1-8, (10042 & 10054)
6 8307912 AR SHIM WASHER, 0.06
7 8307913 AR SHIM WASHER, 0.12
8 8310259 AR SHIM WASHER, 0.09
9 8050001 2 BEARING
10 1001110889 1 FRONT AXLE ASSY, (10042 & 10054), (includes items 101 thru 105) B
101 1001103619 5 SOCKET HD CAPSCREW, M22X1-1/2X80
102 0100019 AR
LOCTITE
®
271
TM
, (apply to item 101)
103 1001107744 1 OUTRIGGER MOUNTING BRACE
104 1001107746 1 FRAME LEVEL CYLINDER LUG
105 Ref FRONT AXLE, (see Figure 5-2 for details)
1001128946 Ref DRIVE SHAFT INSTALLATION, (not available to order, see items 201 thru 217
for service)
B
201 7138638 1 FRONT AXLE DRIVE SHAFT, (includes items 203 thru 206)
202 7138639 1 REAR AXLE DRIVE SHAFT, (includes items 203 thru 206)
203 8035778 4 CROSS & BEARING KIT, (two required per drive shaft)
204 8035109 2 DUST CAP KIT, (one required per drive shaft)
205 NSS 2 SLIP JOINT
206 NSS 2 YOKE SHAFT
207 1001127784 1 DRIVE SHAFT - ENGINE TO TRANSMISSION, (includes items 208 thru 211)
208 1101841 2 CROSS & BEARING KIT
209 8035109 1 DUST CAP KIT
210 NSS 2 SLIP JOINT
211 NSS 2 YOKE SHAFT
212 8310425 4 HEX HD CAPSCREW, 7/16-20X1-1/4, GR8
213 8307006 4 LOCKWASHER, 7/16
214 Use Kit K1 8 STRAP, (use kit 8880218-OM for replacement)
215 Use Kit K1 16 SCREW, (torque to 32-42 lb-ft/43-57 Nm), (must replace when removed, do
not re-torque), (use kit 8880218-OM for replacement)
216 Use Kit K2 2 STRAP, (use kit 8880219-OM for replacement)
217 Use Kit K2 4 SCREW, (torque to 35 lb-ft/47 Nm), (must replace when removed, do not re-
torque), (use kit 8880219-OM for replacement)
218 Ref ZF TRANSMISSION, (see Figure 5-17 for details)
219 Ref ISOLATION COUPLER, (see Figure 4-7 for details)
220 Ref FRAME LEVEL CYLINDER & MOUNTING HARDWARE,
(see Figure 9-5 for details)
221 Ref STABIL-TRAK CYLINDER & MOUNTING HARDWARE,
(see Figure 9-6 for details)