Service Manual User Manual

General Information, Specifications, and Maintenance
2-11
2.5.6 Transmission
A. Transmission Fluid
Vehicle transmissions are factory filled with 10W motor
oil. Any suitable 10W motor oil, which meets the require-
ments of U.S. ordinance specification MIL-L-2104C, can
be used. Products known to meet these requirements
include:
• ARCO TRACTOR FLUID or equivalent
• CASTROL AGRICASTROL HDD
• CASTROL/DEUSOL CRD
• ESSO ESSOLUBE D-3HP
• ESSO ESSOLUBE XD-3
• SAE 10W MOTOR OIL
• SHELL RIMULA CT
• SHELL RIMULA TX
• SHELL RIMULA X
In general, use any approved 10W or 5W20 motor oil
(depending on ambient temperatures; see information
below), Dexron* or Dexron II D*, or an anti-wear hydraulic
oil meeting ISO Grade 46 specifications with a -40°F
(-40°C) pour point/ASTM viscosity SUS 215 at 100°F
(38°C)
.
For -30°F to +120°F (-34°C to 49°C), Dexron* II transmis-
sion fluid with a -50°F pour point may be substituted.
5W20 motor oil may be substituted for use with tempera-
ture conditions of -30
°
F to 70
°
F (-34
°
C to 21
°
C) only.
Products known to meet these requirements include:
• AMOCO RYKON 46
• ARCO DURO AW S-215
• BENZ PETRAULIC 46-7C
• CHEVRON AW HYDRAULIC OIL 46
• CITGO PACEMAKER XD-46 or equivalent
• GULF HARMONY 46
• ISO-46 HYDRAULIC OIL
• MOBIL DTE-25
• SHELL TULLUS 46
• SUN SUNVIS 821 WR
• TEXACO RANDO HD 46
If anti-wear hydraulic oil as specified above is not available,
a suitable tractor fluid may be substituted which meets
the requirements of any of the following specifications:
• ARCO TRACTOR FLUID or equivalent
• DETROIT DIESEL C-3
• FORD TRACTOR M2C134B
• JOHN DEERE J20A
•TEXACO TDH OIL
• WHITE FARM Q1826
Chart 2-1. Transmission fluid temperature range.
PREFERRED OIL VISCOSITY: Select the highest vis-
cosity compatible with prevailing ambient temperatures
and the oil application information listed under
Section
2.5.6 A. Transmission Fluid
.
The Clark Hurth T12000 modulated shift transmission
used in this vehicle should use ONLY C-3 or Tempera-
ture Range 3 transmission fluids, Dexron* or Dexron II
D*.
Note: Dexron II D* is not compatible with graphitic clutch
plate friction material UNLESS IT MEETS THE
APPROVED C-3 SPECIFICATIONS.
*Dexron and Dexron II D are registered trademarks of General
Motors Corporation.
B. Transmission Capacity
Capacity w/ filter change ................. 3.4 gal (12,9 l)
Filter .................................................... 1.5 qt (1,4 l)
60
50
40
30
20
10
0
-10
-20
-30
-40
-50
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
-10
-20
-30
-40
-50
-60
Temperature Range "3"
If using Dexron*,
Use ONLY Dexron*
or Dexron II D*
See NOTE Below
RECOMMENDED LUBRICANTS FOR CLARK-HURTH
T12000 POWER SHIFTED TRANSMISSION
3
Celsius
Farenheit
Model 3606 • Origin 10/99