Installation Guide
REV.3/19-05 Page 5 of 16
PROGRAM REVIEW
If you want to review the settings for either the FACTORY program
and/or your CUSTOMIZED program, you may do so by pressing the
PROG
button for one second. To review other settings, press the
PROG
button allowing one second between each press of the PROG
button. If you press the PROG
button for 4 seconds, then you go
into the programming process. Press the SET
button should you
hold the PROG
button too long.
PROGRAM CANCELLATION
Should you want to cancel the CUSTOMIZED program that you have entered and return to the FACTORY program, you may do so. To
cancel a CUSTOMIZED program:
1. Press the SET
button to make sure the LCD screen is in normal state.
2. Then press and hold the PROG
button and, at the same time, press the SET button for a period of 10 seconds.
3. The customized programs will be cancelled when the display icons/numbers flash with some icons disappearing. The LCD screen
will begin flashing PROGRAM FOR, START AT, and the digits in the TIME and SET frames will begin flashing. This confirms
CUSTOMIZED programs have been cancelled.
4. Push the SET
button to return LCD screen to normal state or wait 10 seconds and LCD screen will return to normal state
automatically.
ADDITIONAL PROGRAMMING OPTIONS SWING (TEMPERATURE DIFERENTIAL)
The thermo-transmitter operates the fireplace system whenever the
ROOM TEMPERATURE varies a certain number of degrees from the
SET TEMPERATURE. This variation is called the “SWING” or
TEMPERATURE DIFFERENTIAL. The normal operating cycle of a
fireplace system may be 2-4 times per hour depending on how well the
room or home is insulated from the cold or drafts. A smaller “swing
number” increases the number of cycles so the room temperature is
more constant. A larger “swing number” decreases the number of
cycles, which saves energy, in most cases. The factory setting for the
“swing number” is 2. This represents a temperature variation of +/- 2
0
F
(1
0
C) between SET temperature and ROOM temperature which
determines when the fireplace will be activated. The “SWING” number
values are:
1= +/- 1
0
F (.5
0
C), 2= +/- 2
0
F (1
0
C), 3 = +/-3
0
F (1.6
0
C).
1. To change the temperature “SWING” setting (1-3), press
the AHEAD + BACK
buttons simultaneously to display the
current “SWING” setting in the SET TEMP frame. The
word SWING will display on the LCD screen.
2. Press the UP
or DOWN button to change the temperature
differential or “SWING” (1-3). See above for 1-3 “SWING”
temperature values.
3. To store the “swing number”, press the SET
button or
allow 15 seconds to lapse, and the new “swing number”
will be automatically programmed.
OPERATING INSTRUCTIONS
THERMO OPERATION – (Systems operates thermostatically based on SET TEMP setting, ONLY)
SETTING DESIRED ROOM TEMPERATURE
This remote control system can be thermostatically controlled when the
transmitter is in the THERMO mode (THERMO must be displayed on the
screen).
1. To set the DESIRED room temperature, press the MODE
button to
place the transmitter into THERMO mode. THERMO ON or OFF
will display.
MANUAL CHECK OF “SWING” OR TEMPERATURE
DIFFERENTIAL
The operation of the factory set “THERMO SWING” can be
checked by adjusting the SET TEMP 2
0
F above or below the
room temperature. This will cause the system to turn ON or
OFF. Normally the system will only respond to temperature
changes every two minutes. Manually
changing the SET
temperature will activate the system in less than 10 seconds. If
the “SWING” is changed, then a new room temperature
differential will respond. Factory setting of SWING temperature
is
2
0
F.
1
MO
EVE
ON
THERMO
TEMP
FLAME
SET
FAN
OFF
OFF
HI
HI
2
UP
DOWN
MODE
TIMER
TIME
SET
PROG
AHEAD
BACK
FAN
FLAME
1
TIME
SET
AM
START
AT
PROGRAM
FOR
SU
MORN
UP
DOWN
MODE
TIMER
TIME
SET
PROG
AHEAD
BACK
FAN
FLAME
SWING
3
2
1
UP
DOWN
MODE
TIMER
TIME
SET
PROG
AHEAD
BACK
FAN
FLAME