Installation Guide

REV.3/19-05 Page 4 of 16
PROGRAMMING DAYS/PERIOD OF DAY/SET TEMPERATURES
PROGRAMMING THE TRANSMITTER
The user may change the built-in time and temperature programs to suit
their personal schedule. Each day is divided into four periods:
MORNING, DAY, EVENING, AND NIGHT. A blank programming chart
is provided to the left to record your customized time and temperature
settings.
If desired, you may change a single day or all seven days that have the
built-in factory program. To change one or all seven days, complete the
following steps:
1. Press the PROG
button for 4 seconds. The shaded boxes on the
LCD screen with the words PROGRAM FOR
and START AT will
begin to flash. The current DAY, PERIOD, TIME and SET
temperature of the BUILT-IN FACTORY PROGRAM will also be
displayed.
NOTE
: If the above settings were not previously completed during the
initial SET-UP and PROGRAMMING procedure, then the LCD screen
will
display SU, MORN, TIME and SET temperature digits. You must go
back and perform the initial set-up procedure or the remote will not
operate properly in the PROGRAM mode.
2. To program
the DAY and PERIOD OF DAY, press the AHEAD or
BACK
buttons to display the DAY and PERIOD you wish to
program.
3. When the DAY and PERIOD being programmed displays, then
press the PROG
button and the TIME will flash on the LCD screen.
4. To program
the START TIME, press the UP or DOWN button.
Programmed start time settings are in 15 minute segments. The
new set time will display on the LCD screen.
5. When the desired START TIME displays, press the PROG
button
and the SET TEMPERATURE will flash on the LCD screen.
6. To program
the SET TEMPERATURE, press the UP or DOWN
button.
7. When the desired SET TEMPERATURE displays, then press the
PROG
button.
8. After pressing the PROG
button in step 7, the next PERIOD of the
same or next day
will display on the LCD screen.
9. To program
the next PERIOD follow steps 3, 4, 5, 6 and 7.
10. Continue to follow steps 3, 4, 5, 6 and 7 until all 7 days and the 4
time periods in each day are programmed.
11. Once ALL
the programming has been completed, then press the
SET
button. The programming data that has been entered will now
over-ride
the factory built-in program and operate your remote
control system.
PROGRAMMING NOTE:
Once in the programming process and you want to advance the
programming procedure, you may bypass some of the DAYS or
PERIODS OF DAY, by pushing the AHEAD
or BACK buttons. This
allows you to eliminate the need to enter the TIME and
TEMPERATURE for each DAY/PERIOD speeding up the programming
process by skipping some of the ”software prompts”. Once the LCD
screen displays a DAY/PERIOD you want to reprogram, press the
PROG
button and follow the programming steps outlined above.
PERIOD
DAY
MORN DAY
EVE NITE TIME/TEMP
SU
MO
TU
WE
TH
FR
SAT
TIME
SET
AM
START
AT
PROGRAM
FOR
SU
MORN
1,3
2
UP
DOWN
MODE
TIMER
TIME
SET
PROG
AHEAD
BACK
FAN
FLAME
TIME
SET
AM
START
AT
PROGRAM
FOR
SU
MORN
5
4
UP
DOWN
MODE
TIMER
TIME
SET
PROG
AHEAD
BACK
FAN
FLAME
TIME
SET
AM
START
AT
PROGRAM
FOR
SU
MORN
7
6
UP
DOWN
MODE
TIMER
TIME
SET
PROG
AHEAD
BACK
FAN
FLAME
TIME
SET
AM
START
AT
PROGRAM
FOR
SU
DAY
11
UP
DOWN
MODE
TIMER
TIME
SET
PROG
AHEAD
BACK
FAN
FLAME