WIRELESS VOICE RELEASE SYSTEM Part Number: 45264 Instruction Manual WARNING: TO AVOID SERIOUS INJURY OR PROPERTY DAMAGE THOROUGHLY READ INSTRUCTIONS BEFORE USING.
Table of Contents Section Page I. Introduction / FCC Notice .................................................................... 1 II. Safety ................................................................................................. 2 III. Contents ............................................................................................. 3 IV. Features and Descriptions .................................................................. 4 V. Programming ...................................
II. Safety WARNING: THOROUGHLY READ INSTRUCTIONS BEFORE INSTALLING OR OPERATING THE WIRELESS VOICE RELEASE SYSTEM! MAKE SURE TRAP IS SAFELY UNCOCKED BEFORE MOVING IN FRONT OF THE TRAP. ACCIDENTAL RELEASE OF THE TARGET AND/OR THROWING ARM CAN CAUSE SERIOUS INJURY OR DEATH! BEFORE INSTALLING THE WIRELESS VOICE RELEASE SYSTEM ON THE TRAP, MAKE SURE THAT THE THROWING ARM IS IN THE UNCOCKED POSITION, THE TRAP IS IN THE OFF POSITION AND THE TRAP IS DISCONNECTED FROM THE BATTERY.
III. Contents A – Receiver (Attach included antenna to top of receiver) B – Sound-Activated Transmitter C – Two AAA/1.
IV. Features and Descriptions Receiver Unit A - ARM Button: o Press the ARM button to allow the receiver to accept transmitter commands and enable receiver output (arm). o Press the ARM button again to prevent the receiver from accepting transmitter commands and disable the receiver output (disarm). B - POWER LIGHT (Green): o Illuminates continuously when receiver is connected to 12V power. C - READY LIGHT (Red): o Illuminates continuously when receiver is armed.
Sound Activated Remote Transmitter TOP A – ON/OFF & MICROPHONE DIAL: o Powers transmitter ON/OFF and illuminates power light o Adjusts microphone sensitivity from 100 db to 80 db. Midrange position starting point. Clockwise will increase microphone sensitivity (quieter sound will activate unit). Transmitter activated by loudness of ANY sound. o Must be set to OFF when not in use to conserve battery life. B – MICROPHONE o To ensure optimum performance keep microphone clear of obstructions such as clothing.
Front G – T1 o Press T1 to select the desired time delay (in seconds) when release signal sent to first receiver after release sequence is started H - #T o Press #T to select number of traps in use J – SEQ o Press SEQ to select trap release sequence. A-B: If #T is 1 then release signal sent to receiver A. If #T is 2 then release signal sent to A then B. M B-A: If #T is 1 then release signal sent to receiver B. If #T is 2 then release signal sent to B then A. A&B: If #T is 1 then this setting unavailable.
V. Programming Programming Receiver with Sound Activated Remote Transmitter Before operation each receiver will need to be programmed to the transmitter being used. 1. Install the AAA 1.5V Batteries in the transmitter if they are not installed. Remove battery compartment cover, insert batteries and replace battery cover. Turn transmitter on (green LED will flash slowly). 2. Connect receiver to 12V Battery, Red clip connects to positive (+), Black clip connects to negative (-).
VI. Installation Attach Trap Connector (contents part D) to foot pedal release cable WARNING: MAKE SURE THAT THE THROWING ARM IS IN THE UNCOCKED POSITION, THE TRAP IS IN THE OFF POSITION AND THE TRAP IS DISCONNECTED FROM THE BATTERY. MAKE SURE THE TRAP FUNCTIONS CORRECTLY USING THE FOOT PEDAL AND ANY ADJUSTMENTS TO THE TRAP ARE MADE BEFORE INSTALLING ANY REMOTE RELEASE SYSTEM.
To foot pedal - If foot pedal is still needed, attach Foot Pedal Connector (see contents part E) to remaining foot pedal release cable using the same procedure. The receiver can then be unplugged and the foot pedal cable plugged back in so foot pedal can be used. - Repeat procedures for other receivers and traps Mounting receiver(s) - Receiver(s) should be mounted above ground level and close to the 12V power source with the receiver antenna pointed straight up.
VII. Operation To operate trap(s) follow the steps below: 1. Safe release trap, set trap main power switch to OFF and disconnect trap from 12V battery 2. Plug receiver output connector into trap connector on release cable of trap 3. Connect trap to 12V battery 4. Connect receiver to 12V battery. Red clip connects to positive (+), Black clip connects to negative (-).
9. Attach transmitter using belt/pocket clip. Preferred in-use transmitter placement for right-handed shooters is on front left pants/shirt pocket or on belt opposite shooting side. Left-handed shooters should place the transmitter on front right pants/shirt pocket or on belt opposite shooting side. For optimum performance keep microphone clear of all obstructions such as clothing. 10.
VIII.
Shooting targets with 2 traps (One trap connected to receiver programmed as A and the other trap connected to receiver programmed as B) 1 Turn on and ARM receivers connected to traps Step 1 Turn on unit and set sensitivity to mid point Step 2 Press T1 and set the desired time delay (in seconds) for the first trap 8 Step 3 Press #T and set to 1 or 2 for number of traps launching targets Step 4 Press SEQ and set sequence of traps If #T set to 1 A-B (receiver A will activate) B-A (receiver B will activate)
IX. Troubleshooting WARNING: MAKE SURE THAT THE THROWING ARM IS IN THE UNCOCKED POSITION, THE TRAP IS IN THE OFF POSITION AND THE TRAP IS DISCONNECTED FROM THE BATTERY BEFORE MAKING ANY ADJUSTMENTS TO RECEIVER OR TRAP. The Trap Arm Rotates But Doesn’t Launch a Target 1. Rotate the adjustment dial located inside the receiver clockwise to a larger number (see Page 11) The Trap Launches More Than 1 Target 1.
ORDERING PARTS Parts can be ordered through the Onalaska Operation’s Customer Service Dept. at (800) 635-7656. Prices are subject to change without notification. Minimum order value of $10.
Warranty and Contact Information LIMITED WARRANTY Your new Champion® Wireless Voice Release System is warranted to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase. This warranty is extended only to the original consumer purchaser. During the warranty period, we will replace any parts that contain defects in materials or workmanship at our expense. You must keep your receipt as proof of the date of purchase.
