User's Manual

ManualsBrandsSkytech II ManualsElectronicsTransmiter

FUNCTIONAL SPECIFICATION

COPRECI “ReMotion” TRANSMITTER

Revision History

Rev. 0: Initial Release. M.R. 7/11/2012.

Rev. 1: Following customer review - Changed LCD indication (flashing indicator) for Thermostat Disable

and Program Disable Features; Changed factory default THERMO SET Temperature from 45-deg. F to 68-

deg. F. M.R. 7/13/2012.

Rev. 2: Changed number of LIGHT settings from 0-2 to 0-3 per customer request. M.R. 8/9/2012

Rev. 3: Removed Flame-A setting memory (RX restriction), added requirement for Continuous Pilot ON to

be default setting, added requirement for main flame to be ON when activating Continuous Pilot (RX

restriction), added Light/Fan/Aux disable features. M.R. 12/13/2012.

Rev. 4: Removed manual selection of Continuous Pilot Mode, specified Pilot Method for Manual,

Thermostat, and Program modes, changed reaction to 1

touch of LCD screen (will only illuminate

backlight – no reaction to associated Zone function). M.R. 12/21/2012.

Rev. 5: Made the factory default for FLAME B, FAN, LIGHTS, and Aux outputs “Disabled” and added

reference to “auxiliary module” when referencing these functions. M.R. 5/6/2013.

Summary of content (10 pages)

PAGE 1
FUNCTIONAL SPECIFICATION COPRECI “ReMotion” TRANSMITTER Revision History Rev. 0: Initial Release. M.R. 7/11/2012. Rev. 1: Following customer review - Changed LCD indication (flashing indicator) for Thermostat Disable and Program Disable Features; Changed factory default THERMO SET Temperature from 45-deg. F to 68deg. F. M.R. 7/13/2012. Rev. 2: Changed number of LIGHT settings from 0-2 to 0-3 per customer request. M.R. 8/9/2012 Rev.
PAGE 2
Objective Define basic construction, touch-screen LCD & button layout, and operational parameters for a wireless transmitter to operate the COPRECI “ReMotion” ignition control module & optional auxiliary module. Basic Construction • Transmitter body should be the same construction as current production model ReMotion TX. • Touch-Screen LCD and three push buttons will allow input from users. • LCD screen will provide system status & input feedback to user.
PAGE 3
Functional Description Note: All function adjustments will be automatically accepted 15-seconds after pressing a given touch zone or button. The user may press the MODE/SET button to immediately accept the adjustment manually. Day and Time Display • The current day of week and time of day will be continuously displayed in the TIME/PROG Zone (except during Setup operations).
PAGE 4
Modes of Operation Operation modes: • MANUAL OFF • MANUAL ON • THERMOSTAT (with optional PROGRAM Mode) The modes may be cycled in the order above by pressing the MODE Zone or the MODE/SET Button. MANUAL OFF Mode: • Transmits flame OFF command.
PAGE 5
• SWING Temperature: This model does not allow for SWING temperature adjustment. This model utilizes thermostatic flame modulation that will modulation the main flame based on the difference between room temperature and set temperature (see example below). o Important - factory SWING TEMPERATURE setting is 2 degrees. The thermostatic flame modulation feature will not allow this SWING to be changed. EXAMPLE: Set Temperature Set Temperature (72) • • • • Room Temp.
PAGE 6
The room temperature will still be measured & displayed in the ROOM TEMP Zone. o The TIME/PROG zone will continue to display the Clock and Day of week, but none of the icons associated with Program Mode will be displayed. To disable or re-enable the Thermostat, the transmitter must be in MANUAL OFF Mode, then press and hold the SET TEMP Zone and the DOWN Button simultaneously for 10seconds. The LCD screen will go blank except either THERMO and OFF or THERMO and ON will flash 3-times (0.5-seconds OFF, 0.
PAGE 7
• • The Program Mode (described above) may be disabled for applications where a program operation is not allowed or undesirable. When Program Mode is Disabled: o The user will not be able to activate Program Mode o The user will not be able to enter Program Setup or edit Program Mode settings. o The TIME/PROG zone will continue to display the Clock and Day of week, but none of the icons associated with Program Mode will be displayed.
PAGE 8
MODE Zone) will flash 3-times (0.5-seconds OFF, 0.5-seconds ON) to indicate the change has been made. Fan Adjustment • Transmits a fan setting command to the control module to adjust the fan output level. • Available settings are 0 (off) – 3 with a factory default setting of 2. If the user changes the fan speed during operation, the control will remember and use the adjusted setting on subsequent fan ON cycles (fan speed memory).
PAGE 9
simultaneously for 10-seconds. The LCD screen will go blank except either AUX and OFF (OFF display in MODE Zone) or AUX and ON (ON display in MODE Zone) will flash 3-times (0.5-seconds OFF, 0.5-seconds ON) to indicate the change has been made. Child-Lock Operation • Child-Lock operation prevents any user input to the transmitter. No mode of operation or feature may be adjusted when Child-Lock is activated. All automatic functions (thermostat, program, etc.) will continue normally.
PAGE 10
FCC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.