User's Manual

Blade guards are great for beginners and are highly recommended
when first learning how to fly a drone. Blade guards add weight and
reduce the drone’s agility. For maximum flight and stunt
performance, blade guards should be removed. When flying in Flight
Sensitivity Mode 3, blade guards should be removed.
FOR BETTER STUNT PERFORMANCE
Before each use, an adult should check this product and the LiPo battery to ensure no damage or
hazards exist. Drone has rotating blades that move at high speed, posing danger of damage and
injury. Pilots are responsible for any actions that result in damage or injury from the improper
operation of drone. Adequate flying space is required. Avoid flying near interior fans and/or vents as
they may make flying difficult to control. Keep a safe distance away from streets, public thorough-
fares and power lines. Never attempt to retrieve drone from any location higher than your reach
(such as rooftops or trees) or from any location that poses a safety hazard. Never fly drone at night.
Keep drone in sight at all times during operation. Discontinue operation immediately if drone flies out
of your field of view. Do not fly near spectators or animals. Keep spinning rotors away from fingers,
hair, eyes and other body parts. Always launch from a flat surface. Never leave drone unattended
while it is turned on. Read all enclosed information before operating.
ADULT SUPERVISION REQUIRED
MORE STUNTS!
For flying tips and instructions on how to perform more
one-touch stunts, please visit www.skyviper.com
If the drone drifts in any direction while hovering (and you are not pressing the direction stick), you may need to make trim adjustments.
Press the recommended trim button as described below to make adjustments.
Tip 1: When the remote LED flashes 3 times quickly, the trim will revert back to middle of trim range.
Tip 2: If you are uncomfortable trimming the drone in flight, you can land onto a flat surface and make your trim adjustments.
.
NOTE:
Trim adjustments will remain saved until remotes batteries
are removed.
TROUBLESHOOTING
TRIM ADJUSTMENTS
• Drone’s blade may have been installed incorrectly. Reinstall and
remember that the GREEN blades point forward.
• Adjust the trim controls until drifting ceases.
• Ensure that drone is flying a minimum distance of 6 feet from the
ground with a minimum 6 feet clearance in all directions.
Drone is
unresponsive
All blades spin, but drone
will not fly properly or
crashes immediately
Drone crashes when
attempting stunt
functions
PROBLEM SOLUTION
If the drone drifts forward
– Press B button
If the drone drifts backwards
– Press F button
If the drone drifts left
– Press R button
If the drone drifts right
– Press L button
If the drone spins counter-clockwise,
when viewed from the top
– Press button
If the drone spins clockwise,
when viewed from the top
– Press button
Drone drifts in any
direction during flight
without direction from
the remote
• Ensure the remote has fresh batteries and the LiPo battery is
fully charged.
• Drone may be miscalibrated by launching from an un-level surface. Turn
the remote off. Turn off the drone then turn them back on and try again
from a flat, level launching surface.
• Inspect drone for any possible damage.
ONE TOUCH STUNTS
BARREL ROLL
While flying forward (or reverse),
tap the stunt button.
NOTE:
Once a stunt has been initiated, DO NOT adjust Throttle or press
any other controls until the stunt has been completed.
FLIP
1 Bring the drone to a mid-air
hover without flying in any
direction. Remove finger
from the direction stick.
2 While hovering, tap and
hold the stunt button.
3 Then quickly tap the
direction stick in the
direction you want the
drone to flip.
CAUTION!
The drone should be flying at least 6 feet in the air with a minimum clearance of 6 feet in all directions
before attempting stunt functions.
RECORDING VIDEO
RECORDING TO
MICRO SD CARD
4GB MICRO SD MEMORY CARD INCLUDED
1. Insert the Micro SD Card into the back
of the Drone.
2. To take a picture during flight press the
PHOTO BUTTON on the remote.
3. To take a video, press the
VIDEO BUTTON on the remote to start
recording. The LED indicator will flash
rapidly when recording. Press the
VIDEO BUTTON again to stop recording.
DOWNLOADING FROM
MICRO SD
Turn off the drone by disconnecting the
battery.
Press in and release the Micro SD Card
located on the back of the drone.
Insert the Micro SD Card into the Micro SD
Card Adapter. Insert the Micro SD Card
Adapter into the USB port on your computer.
The computer will recognize the Micro SD
Card as an external hard drive named
SKYVIPER. Use the computers operating
system or preferred photo transferring
program to transfer the photos and videos.
After the photos and videos have been
transferred, delete photos and videos from
SKYVIPER drive.
You may upgrade to
longer recording
times by replacing the
4gb micro sd card
with higher capacity
micro sd card -
up to 32gb
(Sold separately).
GET MORE
RECORDING TIME
ATTENTION MAC USERS:
If you experience problems downloading and
playing Sky Viper Videos using Quicktime,
please download the free VLC player at
www.videolan.com
CAUTION: never remove the
Micro SD Card Adapter from the
computer during file transfer.
1
2
3