• User Manual • Digital Enhanced Cordless Communication SKYPE™ DECT TELEPHONE
Contents Introduction .................................................................................1 Physical Details.............................................................................2 What the symbols mean .................................................................4 Setting up your telephone ..............................................................4 Installation ...................................................................................5 Important safety information.......
Minimum System Requirements Broadband Internet Service PC with the following minimum specifications: Pentium 400Mhz or above Windows® 2000® or XP® Available USB Port, USB2.0 or USB1.1 Skype® version 1.2 or higher (visit www.skype.com) 128Mb RAM, 256Mb RAM recommended 10Mb Hard Disk space CD ROM for Software Driver Package Content The contents of your product should contain the following items. please contact your dealer immediately. 1. 2. 3. 4. 5. 6. 7. 8. 9.
The Handset and Base Unit Skype Key In idle mode, you can press UP key to access Skype Call List directly. Scrolling Button Press during programming to move through the menu; Press during a call to change the volume in the earpiece. Right Key Press to enter phonebook menu. Press during programming to go back to the previous option; Press to clear digits from the display.
What the symbols mean Batteries Charge Level Whenever this shows ‘nearly empty’ ( ), put the handset on the base unit to charge the batteries. While the batteries are being charged, the level shown will keep changing. Mute Your handset's microphone is muted. Signal Level Shows the signal between the handset and base unit, and disappear when you are out of range of the base unit. Speakerphone Your handset’s loudspeaker is on. Lock Your handset’s keypad is locked.
Installation 1. Choose a suitable site for the base unit Make sure it is not near to another telephone, nor to other electrical equipment. 2. Plug the mains power lead and the telephone line cord into the bottom of the base unit. 3. Plug the mains adapter into a 230 V AC, 50 Hz mains socket with the switch on the socket set to OFF. Note: The illustration of adaptor may vary from country to country. 4. Switch on mains power at the socket 5.
9. Mount the CD-ROM and install the program with CD installation provided. The installation should run automatically. If it doesn’t, begin the installation by opening the CD file namely Setup or Skype Dect. Follow the on-screen instructions to complete the installation. After a successful installation, you will find an icon namely Skype Dect on the desktop. Note: The Skype software must be activated on your PC before you place SkypeOut and Skype™ calls every time.
Making and Answering Calls Note: In standby mode, press any button on keypad except “Talk” button to make the backlight come on before enabling any function. (It means 1st press to turn on the backlight, 2nd press to activate the function button. This is correct for all buttons except for “Talk” button.) To Make an Ordinary Call 1. Enter the telephone number and press Call key to place call; 2. If you make a mistake, press Right key to delete incorrect digits, before you press Call key.
To Toggle between Skype call and PSTN call 1. When you already engaged on an ongoing call, if another Skype call is received, press Right key to enter option menu; 2. Then press Scrolling button to select Hook up and press Left key; 3. Press Right key to enter option menu again; 4. Press Scrolling button to select Switch; 5. Press Left key to toggle the phone connection.
3. Press Left key to confirm, and Right key to clear the old name, then key in the new name; 4. Press Left key to save the edit, also goes to the stored number; press Right key to clear the old number and key in the new number; 5. Then press Left key to save the change To Check Memory You can use this feature to see how many of your Phone Book’s locations have been not used. 1. In standby mode, press Right key, enter Phonebook mode, the display shows the stored numbers; 2.
3. Choose the picture you prefer, and then press Left key to confirm, now the picture is set to the wallpaper of the handset. To Set External/Internal Ringer Volume 1. Select < Ringer Set> under Handset Set mode; 2. Press Left key to confirm, then Scrolling button to the location ExternalVo/InternalVol; 3. Press Left key and Scrolling button to choose the volume level you want to set; 4. Then press Left key to confirm the choice. To Set External/Internal Ringer Melody (1 - 9 melody) 1.
Press Left key and “ “ button consecutively to lock/unlock the keypad. To Enter Base Settings Mode 1. 2. Select Settings under menu mode; Press left key select Base Settings and the display shows Ringer Settings, Dial Settings, Call Barring, LCR(Optional), PIN and Default Settings. To Set Base Volume 1. 2. 3. 4. Select < Ringer Settings> under Base Settings mode; Select under Ringer Settings; Press Left key and Scrolling button to set the volume you like; Press Left key to confirm.
2. 3. 4. Then press Left key, the display shows the call barring number you set; Press and hold Right key to clear the number; Press Left key to confirm. Least cost route (LCR) function (Optional) With the LCR function, the phone will automatically replace a long number with a comparative short number, to simplify the process of dialing a long number.
6. After a while, when the handset finds the base unit, it goes back to the standby mode. To de-register a handset You may need to do this if you have more than one handset registered to your base unit and you need to replace a faulty handset. 1. Select under REGISTRATION mode. 2. Press Left key, then key in the PIN (default 0000). 3. Press Left key, then key in the number of the handset you want to de-register. 4. Press Left key to confirm.
To Call a Skype™ User Make sure the Skype™ user is available in your Skype net Contact list and is online. Otherwise, add the online Skype™ user name you wish to call to the Contacts list of Skype net fist. It will automatically appear in your phone’s Skype list. To call a Skype™ user: 1. Press Scrolling Up button to enter Skype mode directly, the display shows the stored names; 2. Press Scrolling Up / Down button to select the name you wish to contact; 3.
2. 3. 4. 5. Select < User Status > under Skype mode; Press Left key, then the display shows the selection status; Press Scrolling button to select the status you wish to set; Press Left key to save. To Set Skype Microphone and Speakerphone located at the bottom-right hand side; 1. Right click on the Skype DECT icon 2. Select Volume Control; 3. Set the Speaker or MIC as required. Illustration below. To Make a Skype Conference Call: 1.
On the other handset's display, your number appears, and the INT symbol flashes. Then the other handset user presses the Call key to connect the call. For details of how to change the ringing melody and volume for intercom calls, see "INT MELODY" and "INT VOLUME" under "HANDSET SETTING" part. To End an Intercom Call Press the Call key on your handset. The other person will hear Busy tone, and also need to press the End key to hand up.
The phone does not ring Check that the base unit’s mains power adapter is plugged in and power is switched on. The base unit needs mains power for normal operation of the phone-not just charging the batteries. Make sure you are using the telephone line cable that was supplied with your telephone. Other telephone line cables might not work. Check that you have set the ringer volume to off. See the user manual for more information.
Electrical power Base unit Headset Earpiece PABX compatibility HandsetOne 1.2 x 2 V 750 mAH Ni-MH, Rechargeable battery cell Input 230 V AC, 50 Hz; Output AC 7.5V, 350 mA. 2.5mm jack Pause length: 3 seconds.
