Manualshelf

Quick Start Guide

ManualsBrandsSkylo Technologies ManualsComputers & AccessoriesWireless IoT Hub
12345678910
SKYLO TECHNOLOGIES | 2 68 Lambert Ave., Palo Alto, CA 94306 | WWW.SKYLO.TECH
Software
Obtain and install the Skylo mobile application on your mobile phone.
Setting Up the Hub
Locating and Installing the Hub
Follow these steps to setup Hub to connect to the Skylo network. See the images in Appendix A for
installation and removal.
1.
M
a
k
e
n
o
t
e
o
f
t
h
e
H
ub
’
s
i
d
e
n
t
i
f
y
i
n
g
i
n
f
o
r
m
a
t
i
o
n
l
ab
e
l
(
w
i
t
h
M
AC
I
D
,
e
t
c
.
)
s
h
o
u
l
d
y
o
u
r
e
qu
i
r
e
i
t
a
t
a
later stage when onboarding the Hub.
2.
Identify an outdoor location, with a clear view of the sky.
3.
Choose a location for the hub. It should be as flat and level as possible.
4.
If installing on a vehicle, align the arrow on the MMP in the direction of vehicle forward
movement.
5.
Secure the MMP to the desired location. It can be secured via a wide range of fasteners. See
Skylo Reference User Guide for v4 Hub Installations for detailed information.
6.
Mate the Hub to the MMP. Choose one of four possible orientations for the Hub that places the
M12 connector and/or the attention button in the most convenient location. Place the Hub over
t
h
e
c
e
n
t
e
r
o
f
t
h
e
MM
P
,
ab
o
u
t
⅛
o
f
a
t
u
r
n
co
un
t
e
r
c
l
oc
k
w
i
s
e
(
CC
W
)
r
e
l
a
t
i
v
e
t
o
t
h
e
MM
P
.
A
f
t
e
r
t
h
e
H
ub
s
l
i
d
e
s
d
o
wn
i
n
t
o
t
h
e
c
e
n
t
r
a
l
h
o
l
e
o
f
t
h
e
MM
P
,
r
o
t
a
t
e
i
t
⅛
o
f
a
t
u
r
n
c
l
oc
k
w
i
s
e
(
C
W
)
t
o
l
oc
k
i
t
into place.
7.
I
f
o
p
e
r
a
t
i
n
g
f
r
om
e
x
t
e
r
na
l
p
o
w
e
r
,
a
tt
a
c
h
t
h
e
M
12
co
nn
e
c
t
o
r
e
nd
o
f
t
h
e
ha
r
n
e
ss
t
o
t
h
e
H
ub
’
s
M
12
co
nn
e
c
t
o
r
.
S
e
c
u
r
e
and
r
o
u
t
e
t
h
e
ha
r
n
e
ss
t
o
t
h
e
s
o
u
r
c
e
o
f
D
C
p
o
w
e
r
(
e
.
g
.
,
t
o
a
v
e
h
i
c
l
e
’
s
12V
d
c
adapter). Ensure that the harness does not physically strain the M12 connector at the Hub. Two
cable ties have been included in your kit specifically for this purpose by attaching the cable to
cable “tie downs” located along the MMP edge.
8.
Apply power (via the M12 harness) or press the attention button on the hub (if battery powered)
to turn on the Hub.
On
c
e
i
n
s
t
a
ll
e
d
o
n an
MM
P
,
t
h
e
H
ub
i
s
s
e
c
u
r
e
l
y
a
tt
a
c
h
e
d
t
o
t
h
e
MM
P
and
c
an b
e
d
e
p
l
o
ye
d
o
n
mo
v
i
n
g
vehicles and other mobile platforms.
T
o
s
e
pa
r
a
t
e
a
H
ub
f
r
om
i
t
s
MM
P
,
f
o
ll
o
w
t
h
e
s
e
s
t
e
p
s
:
1.
I
n
s
e
r
t
t
w
o
H
ub
r
e
l
e
a
s
e
k
ey
s
b
e
t
w
ee
n
t
h
e
H
ub and
MM
P
,
i
n
t
h
e
s
l
o
t
s
d
e
s
i
g
na
t
e
d
f
o
r
t
h
e
m
.
2.
Tw
i
s
t
t
h
e
hub
s
l
i
g
h
tl
y
co
un
t
e
r
c
l
oc
k
w
i
s
e
(
CC
W
)
,
a
r
o
und
1
/
16
t
h
o
f
a
t
u
r
n
.
3.
Remove the two Hub release keys.
4.
Finish turning the Hub CCW until you encounter a stop. Then lift the Hub off the MMP.