Wireless External Alarm Model: SA-001S User’s Instructions
TABLE OF cONTENT 2 INTRODUCTION................................................................................................... INSTALLATION.............................................................................................. 2-4 PROGRAMMING – LEARN REMOTE OR SENSORS OR CONTROL PANEL....................... 4-6 ERASE REMOTE OR SENSOR OR CONTROL PANEL FROM THE WIRELESS EXTERNAL ALARM.......................................................... 7 ALARM SOUND DURATION..................................
Introduction Congratulations on purchasing the Skylink Wireless External Alarm SA-001 Series. The SA-001 Series provide you with a piercing siren and powerful features yet ease to use. You will find the installation to be simple and be able to get the unit up and running easily. The following items are included in this package: - One Wireless External Alarm AC adapter * Rechargeable Battery Pack User’s Instructions * - Option Installation - Remove the cover of the Wireless External Alarm as shown.
- Set Compatibility Jumper: Refer to the following table to setup the Wireless External Alarm to work with different Skylink’s Security System or Sensors. To select, you will see a jumper connector marked “J2” as shown below. Use a paper clip to remove the jumper connector and re-locate to the proper posts.
Insert the rechargeable battery pack to the black connector marked “NiMH” Plug in AC adapter Plug in AC adapter CAUTION: The adaptor as a disconnect devices: − the socket-outlet shall be installed near the equipment and shall be easily accessible. Programming – Learn remote or sensors or control panel In order for the remote or sensor or control panel to communicate with the External Wireless Alarm properly, this need be programmed into the Wireless External Alarm previously.
Learn/ Set 3B – Learn motion sensor to the Wireless External Alarm: - Press and hold the Learn button on the Wireless External Alarm for 2 seconds and then release. The Learn/Set LED will flash. - Activate the motion sensor by pressing the “Test/Set” button on the motion sensor. This “Test/Set” button is located inside the battery compartment. - You will hear 2 beeps and the LEDs will flash twice indicating the sensor is now programmed to the Wireless External Alarm.
3C – Learn door/window sensor to the Wireless External Alarm: - Press and hold the Learn button on the Wireless External Alarm for 2 seconds and then release. The Learn/Set LED will flash. - Activate the Door/Window Sensor, by separating the magnets to send the signal. - You will hear 2 beeps and the LEDs will flash twice indicating the sensor is now programmed to the Wireless External Alarm.
Programming – Erase remote or sensor or control panel from the Wireless External Alarm To erase unwanted remote(s) or sensor(s) or control panel(s) from the Wireless External Alarm will erase all learned devices from the Wireless External Alarm. - Press and hold the Learn/Set button on the Wireless External Alarm for 8 seconds. - While holding the Learn/Set button on the Wireless External Alarm until the Learn/Set LEDs turn on. You may release the Learn/Set button when the Learn/Set LED stay on.
Programming – Arming Sequence The Wireless External Alarm can be programmed to react 2 arming sequences when it receives the signal from the sensor. In order to arm the Wireless External Alarm, the remote (optional) must be programmed to the Wireless External Alarm. You may arm the Wireless External Alarm in 2 different sequences: PANIC ARM HOME ARM AWAY DISARM 6A – Arm Home Sequence: This setting is used when you wish to secure the area but will be at home and moving around within the armed area.
- You will hear 1 beep and the LEDs will flash once indicating the Wireless External Alarm is being counted to Away mode. - After 30 seconds, you will hear 2 beeps and the LEDs will flash twice indicating the Wireless External Alarm in Away mode. 6C – Disarm - Pressing the DISARM button on the remote will disarm the Wireless External Alarm instantly. - You will hear 2 beeps and the LEDs will flash twice indicating the Wireless External Alarm is disarmed.
Operating the Skylink Security Control Panel The Wireless External Alarm is designed to work with the Skylink security control panel such as AM-001, ML-001 and SC-001. Put the control panel that you plan to program into programming mode. Refer to the User’s Instructions of that control panel. 7A – Learn control panel AM-001 or ML-001 to the Wireless External Alarm: - Press and hold the Learn button on the Wireless External Alarm for 2 seconds and then release. The Learn/Set LED will flash.
Learn/ Set Connect the Wireless External Alarm with your existing alarm system You may connect your existing alarm system with the Wireless External Alarm so that the Wireless External Alarm will be triggered by your alarm system. There are 2 ways you can connect your Wireless External Alarm with your existing alarm system. The input terminals (INPUT1 or INPUT2) can be a Normally Open (NO) momentary dry contact or the DC voltage of 12V.
a lert Notification Jumper You can enable or disable the Alert Notification. When it is set to enable, the Wireless External Alarm will beep when arm or disarm or during the entry/exit countdown period. When it is set to disable, the Wireless External Alarm will not beep when arm or disarm or during the entry/exit countdown period. However, the LED will remain flashing as it is. The Wireless External Alarm will still siren when it is triggered.
BATTERY When the battery power is being reduced, the Wireless External Alarm will emit 3 beeps when the remote arm or disarm the unit. It is time to replace the batteries or recharge the battery pack (rechargeable battery only) as soon as the low battery signal appears. Ensure all the batteries are replaced altogether at the same time. The Wireless External Alarm is powered by 3 AA-size Alkaline batteries as the backup purpose. Follow the instructions below to replace the batteries; 1.
Maintenance Your Wireless External Alarm requires few simple maintenance to ensure its continued reliability and operation. - The solar panel on the top housing should be cleaned using the soft and damp cloth. This will ensure the solar panel receives all the available light. - Test the Wireless External Alarm periodically to ensure the unit is working.
Trouble Shooting Questions Solutions Why the Wireless External Alarm does not respond to the sensors or remote? You must program the sensors or remote to the Wireless External Alarm before they can work together. Why I can’t arm my system? Make sure none of the sensors are triggered. For example, the door/window sensor should be in close status.
FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IC Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
CUSTOMER SERVICE If you would like to - find out the up-to-date specifications - know more about features and applications - download documents, i.e. user’s instructions - order Skylink products or if you have difficulty getting the products to work, please: 1. visit our FAQ section at www.skylinkhome.com, or 2. email us at support@skylinkhome.com CUSTOMER SERVICE Rm 1303, Block B, Veristrong Industrial Centre, 36 Aupuiwan Street, Fotan, N.T. Hong Kong. Email:sales@skylinkhome.com http://www.skylinkhome.
DEC,2012 19 101Y035
