Owners manual

ManualsBrandsSKYJACKER ManualsAutomotiveSkyjacker F52MS Aluminum Spacer Leveling Kit

2005 - 2011 Ford Super Duty

1" - 2.5” Metal Spacer

Installation Instructions

REQUIRED TOOL LIST:

* Safety Glasses

* Metric / Standard Wrenches & Sockets

* Floor Jack

* Jack Stands

* Measuring Tape

* Torque Wrench

I-F51-52MS 4-11 Pg 1

Before beginning the installation, thoroughly & completely read these instructions & the enclosed

driver’s WARNING NOTICE. Affix the WARNING decal in the passenger compartment in clear view

of all occupants. Please refer to the Parts List to insure that all parts & hardware are received prior

to the disassembly of the vehicle. If any parts are found to be missing, contact SKYJACKER

Customer Service at 318-388-0816 to obtain the needed items. If you have any questions or

reservations about installing this product, call SKYJACKER

Technical Assistance at 318-388-0816.

Make sure you park the vehicle on a level concrete or asphalt surface. Many times a vehicle is not

level (side-to-side) from the factory & is usually not noticed until a lift kit has been installed, which

makes the difference more visible. Using a measuring tape, measure the front & rear (both sides)

from the ground up to the center of the fender opening above the axle. Record this information

below for future reference.

Driver Side Front: Passenger Side Front:

Driver Side Rear: Passenger Side Rear:

IMPORTANT NOTES:

• If larger tires (10% more than the stock diameter) are installed, speedometer recalibration will be

necessary. Contact your local Ford dealer or an authorized dealer for details.

• After installation a qualified alignment facility is required to align the vehicle to OEM specifications.

www.skyjacker.com

Summary of content (4 pages)

PAGE 1
2005 - 2011 Ford Super Duty 1" - 2.5” Metal Spacer Installation Instructions www.skyjacker.com Required Tool List: * Safety Glasses * Metric / Standard Wrenches & Sockets * Floor Jack * Jack Stands * Measuring Tape * Torque Wrench Before beginning the installation, thoroughly & completely read these instructions & the enclosed driver’s WARNING NOTICE. Affix the WARNING decal in the passenger compartment in clear view of all occupants.
PAGE 2
Kit Box Breakdown: Part #: F51MS ITEM# DESCRIPTION F51MS-S HB-F51MS I-F51/52MS 1" METAL SPCR 05-11 F250/350 HDWR BAG: F51MS SPACER KIT INST SHEET: F51MS / F52MS QTY 2 1 1 Hardware Bag Breakdown: HB-F51MS HARDWARE BAG ITEM# DESCRIPTION 14X90MMB 916XTFW LT100 14MM X 90MM - 2.0 TP BOLT 9/16"EXTRA THICK WASHER,GR8 NUTS N' BOLTS 427 1 ML TUBE QTY 2 2 1 Part #: F52MS ITEM# DESCRIPTION F52MS-S HB-F52MS I-F51/52MS 2.
PAGE 3
Installation: 1. With the vehicle on flat level ground, set the emergency brake & chock the rear tires. 2. Raise the front of the vehicle & support securely using jack stands. 3. While supporting front axle with a floor jack, remove the front tires / wheels using a 21mm socket. Photo # 1 4. Disconnect the drag link from the pitman arm using a 24mm socket & disconnect the front sway bar end links from the axle using 18mm & 21mm socket. (See Photo # 1) 5.
PAGE 4
Photo # 4 OEM Coil Spring Front Of Vehicle 14mm Bolt 9/16" Washer OEM Coil Spring Seat New Coil Spring Seat Spacer FINAL NOTES: • After the installation is complete, double check that all nuts & bolts are tight. Refer to the following chart below for the proper torque specifications. (Do not retighten the nuts & bolts where thread lock compound was used.