User Manual

ManualsBrandsSKYCATCH ManualsRemote ControllerSKYCATCH Secure Remote Controller for DJI M300

Installing the Batteries

1. TheperformanceoftheFlightBatteryissignificantlyreducedwhenflyinginlowtemperature

environments(temperaturesbelow5℃).Ensurethatthebatteryisfullychargedandthecellvoltage is

at4.4Vbeforeeachflight.

2. Endtheflightassoonasthe appdisplaysthe“LowBatteryLevelWarning”inlowtemperature

environments.Youwillstillbeabletocontroltheaircraft’smovementwhenthiswarningistriggered.

3. Inextremelycoldweather,thebatterytemperaturemaynotbehighenoughevenafterwarmingup.In

Pairing Batteries

Beforerstuse,itisrecommendedtomark2batteriesasapairandcontinueusingthemasapair(charge

anddischargethemtogether)tomaximizeservicelifeandensureightperformance.Iftwobatteries

withasignicantdierenceinbatterylifeareinstalledandpoweredon,apromptwillpopupintheapp

torecommendthatyoureplacethebatteriestoapairwithsimilarperformance.

Turning On / O

Thebatterycanonlybeturnedonandoffafteritisinstalledonthe

aircraft.

TurningOn:PressthePowerbuttononce,thenpressagainandholdfor3

secondstoturnon.ThePowerLEDwillturngreenandtheBatteryLevel

Indicatorswilldisplaythecurrentbatterylevel.

TurningO:PressthePowerbuttononce,thenpressagainandholdfor

3secondstoturno.ThePowerLEDandtheBatteryLevelIndicatorswill

beo.

Replacing the Batteries When Turned On

Ifthebatteryneedstobereplacedimmediatelyafterlanding,youcanreplaceitwithoutturningoff

theaircraft.Replacewithonefullychargedbattery,andwaitfor3seconds,andthenreplaceanother

battery.

Heating the Battery

ManualHeating:IftheFlightBatteryisnotinstalledintotheaircraft,pressandholdthebatterylevel

buttononthebatteryforfoursecondstoinitiatetheself-heating,keepingthebatteriesatatemperature

between 61° F (16° C) and 68° F (20° C), which is the ideal range of operating temperature, for

approximately30minutes.Pressandholdthebatterylevelbuttonfortwosecondstostopheating.

AutoHeating:Insertthebatteriesintotheaircraftandpoweriton.Ifalowbatterytemperatureis

detected,thebatterywillautomaticallyheat up tomaintainatemperaturebetween61°F(16°C)and

68°F(20°C).

LowTemperatureNotice:

Confidential

Do not publish

Summary of content (9 pages)

PAGE 1
Installing the Batteries Pairing Batteries C D on o f no ide t p nt ub ial lis h Before first use, it is recommended to mark 2 batteries as a pair and continue using them as a pair (charge and discharge them together) to maximize service life and ensure flight performance. If two batteries with a significant difference in battery life are installed and powered on, a prompt will pop up in the app to recommend that you replace the batteries to a pair with similar performance.
PAGE 2
these cases, insulate the battery as required. 4. To ensure optimal performance of the battery, keep the battery temperature above 16℃. 5. In low temperature environments, it will take a longer time for the batteries to warm up. It is recommended to keep the battery warm before use to reduce the warm-up time. Checking Battery Levels When the battery is turned off, press the Battery Level button once and the Battery Level Indicators will display the current battery level.
PAGE 3
RTK Introduction The aircraft has a built-in RTK, which can withstand magnetic interference from metal structures, ensuring stable flight. Enable / Disable RTK C D on o f no ide t p nt ub ial lis h Ensure that the “Aircraft RTK” is enabled and RTK service type is correctly set before each use. Using the Custom Network RTK You can mount a Dongle to the remote controller or use the app to connect to a Wi-Fi, and enable Internet network to use the Custom Network RTK.
PAGE 4
ADS-B Sensor Airplanes and helicopters with an ADS-B transceiver will actively broadcast flight information including location, flight path, speed, and altitude. ADS_B sensor receives this by ADS-B transceivers via an on-board receiver or internet connection.
PAGE 5
Expansion Ports C D on o f no ide t p nt ub ial lis h The Explore2 offers several SDK expansion ports on the top and bottom of the aircraft. These expansion ports enable developers to explore more possibilities and functions with the aircraft. Top view Bottom view Explore2 supports three payload SDK ports and one onboard SDK port. The external power supply capacity of the payload SDK port is 17.0 V / 13.6 V 4 A. The external power supply capacity of onboard SDK port is 24 V 4 A.
PAGE 6
C D on o f no ide t p nt ub ial lis h Remote Controller This section describes the features of the remote controller that includes aircraft and remote controller operations.
PAGE 7
Remote Controller Profile The Skycatch Secure Controller (hereinafter referred to as “Secure Controller”) features radio technology, capable of controlling aircraft that supports this technology, and providing a live HD view from the aircraft's camera. It can transmit image data at distances of up to 9.32 mi (15 km) and comes with a number of aircraft and gimbal controls as well as some customizable buttons. * C D on o f no ide t p nt ub ial lis h The built-in 5.
PAGE 8
External Battery 1. Connect the Charging Station to a power outlet (100-120 Vac, 50-60 Hz / 220-240 Vac, 50-60 Hz). 2. Press the Power Button once to turn on the Charging Station. 3. Insert the batteries into the Battery Ports to start charging. The Charging Station will charge the battery with the highest remaining battery power first. C D on o f no ide t p nt ub ial lis h Power Outlet Mounting the RC Battery 1 Press and hold the battery release button.
PAGE 9
Remove the dongle compartment cover. Insert the dongle into the USB port with the SIM card inserted into the dongle. C D on o f no ide t p nt ub ial lis h Reattach the cover firmly. Adjusting the Antennas Lift the antennas and adjust them. The strength of the Secure Controller signal is affected by the position of the antennas.