Owner manual

ManualsBrandsSky-Watcher ManualsOptical devicesSYNSCAN GPS

instruction manual

SynScan

GPS

221112V3

1. A SynScan® GPS mouse

(GT-320FW(3.0)) with a MINI-DIN connector at one end of

1.5-meter cable.

2. A 50-cm adapter cable:

Used for connecting between SynScan® GPS mouse and

SynScan™ hand control. One end of the cable is a MINI-

DIN(F) connector, and the other is a RJ-12, 6-pin connec-

tor.

Notes:

• Only SynScan® rmware version 3.32 or later is able to connect to the GPS

(GT-302FW(3.0))module.RegardingtheSynScan®rmwareupdateprocedure,

please read the SynScan® Instruction Manual.

• RegardingSynScan®GPSmousepreviousversion(GT-320FW(2.0)orprior)

pleaserefertotheinstructioninthecontentoftheprovidedCD.

PACKAGE INCLUDES:

Summary of content (5 pages)

PAGE 1
instruction manual SynScan GPS ® PACKAGE INCLUDES: 1. A SynScan® GPS mouse (GT-320FW(3.0)) with a MINI-DIN connector at one end of 1.5-meter cable. 2. A 50-cm adapter cable: Used for connecting between SynScan® GPS mouse and SynScan™ hand control. One end of the cable is a MINIDIN(F) connector, and the other is a RJ-12, 6-pin connector. Notes: • Only SynScan® firmware version 3.32 or later is able to connect to the GPS (GT-302FW(3.0)) module.
PAGE 2
INTRODUCTIONS FOR USE 1. If the firmware version of your SynScan® hand controller is earlier than version 3.32, you should update the firmware to version 3.32 or later. Regarding the SynScan™ firmware update procedure, please read the SynScan® Instruction Manual. 2. If the firmware version of the SynScan® hand controller is version 3.32 or later, your hand controller is ready to be connected to SynScan® GPS mouse. First connect the adapter cable to SynScan® GPS mouse. (Fig. 1) Fig. 1 3.
PAGE 3
INSTRUCTIONS FOR USE 4. Connect DC power (12V): a) If the hand controller is connected to the mount (Fig 4), plug the 12V DC power source into the mount and press the mount’s power switch on (Fig. 5) b) If the hand controller is not connected to the mount, plug the 12V DC power source directly into the hand controller. (Fig. 6) Fig. 3 Fig. 4 Fig. 5 Fig. 6 5.
PAGE 4
INSTRUCTIONS FOR USE 7. After SynScan® GPS mouse has fixed on the GPS signal, the hand controller will display the version number if the hand controller is connected to the mount, or the LCD will display “No link to M.C.” and “Stand-alone mode”, if the hand controller is not connected to the mount.. 8. Press ESC, and the hand controller will function as normal. If the GPS signal is fixed successfully, the hand controller will skip the location, date, and time entry.
PAGE 5
INSTRUCTIONS FOR USE 2012/11/22 . . l ) GPS Information: k) GPS Information: # of SV(fix)= 7 j ) . i ) h) M.O.V.= 018.6˚ GPS Information: Number of SV= 10 a) GPS Information: b) GPS Information: c) GPS Information: Date: 2006/07/25 d) GPS Information: UT= 17:53:40 e) Lat:49˚ 09’23.0”N Lo:123˚ 05’25.0”W GPS Information: LT= 10:53:40 AM GPS Information: Quality: 3D+DGPS f ) GPS Information: Time Zone=-08:00 GPS Information: Altitude: 15 m g) GPS Information: LST: 21:23:45 Fig.