User Manual

SS-100
User’s Manual
•TV size range: 9” to 32“
•Max weight load 39.6 lbs / 18 kg
•Universal VESA 100x100 and 200x200
Disclaimer
Sky Wire intends to make this manual accurate and complete, however, Sky Wire makes no
claim that the information contained herein covers all details, conditions or variations, nor
does it provide for every possible contingency in connection with the installation or use of
this product. The information contained in this document is subject to change without notice
or obligation of any kind. Sky Wire makes no representation of warranty, expressed or
implied, regarding the information contained herein. Sky Wire assumes no responsibility for
Warnings & Cautions
IT IS HIGHLY RECOMMENDED THAT THIS PRODUCT BE INSTALLED BY A PROFES-
SIONAL.
PLEASE REVIEW THIS INSTRUCTION MANUAL COMPLETELY BEFORE STARTING THE
INSTALLATION PROCESS.
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not
follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if
you do not follow the corresponding instruction.
WARNING: Improper installation can result in serious personal injury! Make sure that the
equipment. If not, reinforce the structure before starting the installation.
WARNING: Be aware also of the potential for personal injury or damage to the unit if it is not
adequately mounted.
WARNING: The installer is responsible for verifying that the wall or ceiling to which the
mount is anchored will safely support the combined load of all attached components or other
equipment.
WARNING: The weight of the display placed on the mount must not exceed the maximum
load capacity of the mounts.
WARNING:
WARNING: Make sure the mount and brackets are correctly oriented.
CAUTION: Check the unit for shipping damage before you begin the installation.
1a. Drywall installation
Find studs in wall. Using wall plate (1) as a template, making sure it’s
leveled, mark the two mounting holes on the center of the wood stud.
Drill two holes of 1/8” (3 mm) diameter and 2” (50 mm) deep.
Level wall plate and bolt to wall with 2 lag bolts (F) and 2 washers (E).
1b. Concrete Installation
Using wall plate (1) as a template, making sure it’s leveled, mark the two
mounting holes on the wall.
Drill two holes of 7/16” (10.5 mm) diameter and 2” (50 mm) deep.
wall.
Level wall plate and bolt to wall with 2 lag bolts (f) and 2 washers (E).
2. Bolt TV plate to TV *
Center TV plate on the back of your TV and align the four mounting holes.
washers (E).
*If your TV has a 200 x 200 hole pattern, skip this step.
3. Install Extensions
If your TV has a 200 x 200 hole pattern, install the extensions.
Start by aligning the outer holes of the TV plate with the inner holes
of the extensions as described in the dawing.
Bolt the extensions with 4 bolts (4), 4 washers (5) and 4 nuts (6).
3. Slide in TV Plate on Wall Plate
Align the TV and the mounted wall plate horizontally.
Slide TV from top to bottom until it stops where the plates have
engaged.
Install safety bolt from top.
Wood stud
2” (50 mm)
Ø 1/8” (3 mm)
For more information, visit:
www.cambreproducts.com
Sky Wire
TM
name, logo and model
numbers are property of Cambre.
© Cambre
®
2011
Concrete Wall
Ø 7/16 po (10,5 mm)
2 po (50 mm)
Parts list
200
02 0
1. Wall plate (x1) A M4 x 8 bolt (x4)
2. Adapter bracket (x1) B M4 x 12 bolt (x4)
3 Bolt (x4) C M5 x 8 bolt (x4)
4. Washer (x4) D M5 x 12 bolt (x4)
5. Nut (x4) E M5 washer (x6)
6. Extension plate (x2)
F Lag Bolt (x2)
G Concrete anchor (x2)
E
G
F
F
E
1
2
1
2
3
4
5
6
A-D
E
F
G
1
2
5
4
3
6
A,B,C,D
E
2