User Manual

-2-
Table of Contents
Safety Symbols
The definitions below describe the level of severity for each signal word. Please read the manual
and pay attention to these symbols.
!
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER indicates a hazardous situation which, if not avoided, will result
in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, will result
in death or serious injury.
CAUTION, used with the safety alert symbol, indicates a hazardous
situation which, if not avoided, will result in minor or moderate injury.
Page
General Safety Rules . . . . . . . . . . . . . . . . . . .3, 4
Additional Safety Rules . . . . . . . . . . . . . . . . .5, 6
Motor Specifications &
Electrical Requirements . . . . . . . . . . . . . . . . . . .7
Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . .8
Tools Needed for Assembly . . . . . . . . . . . . . . . .9
Getting To Know Your Table Saw . . . . . . . .10, 11
Unpacking and Checking Contents . . . . . . . . .12
Table of Loose Parts . . . . . . . . . . . . . . . . . .12
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . .13–18
Attaching Smart Guard
System Components . . . . . . . . . . . . . .13, 14
Changing The Blade . . . . . . . . . . . . . . .15–16
Attaching The Rip Fence for Use . . . . . . . .16
Storage, Transporting, & Mounting . . . . . .17, 18
Adjustments . . . . . . . . . . . . . . . . . . . . . . . .19–24
Adjusting 0º & 45º Positive Stops . . . . . . . .19
Adjusting Blade Parallel to the
Slot Miter Gauge . . . . . . . . . . . . . . . . . . . . .20
Aligning Rip Fence . . . . . . . . . . . . . . . . . . .21
Rip Fence Pointer Adjustment . . . . . . . . . .21
Table Pointer Adjustment . . . . . . . . . . . . . .22
Adjusting Riving Knife . . . . . . . . . . . . . .22–24
Adjusting Table Insert . . . . . . . . . . . . . . . . .24
Page
Basic Table Saw Operation . . . . . . . . . . . .24–35
Safety Power Switch . . . . . . . . . . . . . . . . . .24
Smart Guard System . . . . . . . . . . . . . . . . .25
Blade Bevel Control . . . . . . . . . . . . . . . . . .26
Extending Table Extension . . . . . . . . . . . . .26
Using Rip Fence Pointer . . . . . . . . . . . . . . .26
Using Table Pointer . . . . . . . . . . . . . . . . . . .26
Work Helpers . . . . . . . . . . . . . . . . . . . . . . .27
Using the Miter Gauge . . . . . . . . . . . . . . . .28
Crosscutting . . . . . . . . . . . . . . . . . . . . . . . .29
Repetitive Crosscutting . . . . . . . . . . . . . . . .30
Miter Cutting . . . . . . . . . . . . . . . . . . . . . . . .30
Bevel Crosscutting . . . . . . . . . . . . . . . . . . .30
Compound Miter Cutting . . . . . . . . . . . . . . .30
Using the Rip Fence . . . . . . . . . . . . . . . . . .31
Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Non Through Sawing . . . . . . . . . . . . . . . . .33
Rabbeting . . . . . . . . . . . . . . . . . . . . . . . . . .33
Dado Cutting . . . . . . . . . . . . . . . . . . . . .34, 35
Maintaining Your Table Saw . . . . . . . . . . . .36–38
Clearing Dust Chute/ Scoop . . . . . . . . . . . .36
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . .37
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . .39
2610039875 12-15 E_SPT70WT 12/23/15 10:54 PM Page 2