Warranty
-14-
))+9958/+9
, '4 +>:+49/54 )58* /9
4+)+99'8? ' )58* =/:.
'*+7;':+ 9/@+ )54*;):589 :.': /9 )'6'(2+
5,)'88?/4-:.+);88+4:4+)+99'8?,58?5;8
:552 3;9: (+ ;9+* This will prevent
excessive voltage drop, loss of power or
overheating. Grounded tools must use 3-wire
extension cords that have 3-prong plugs and
receptacles.
The smaller the gauge number, the
heav i er the cord.
&$
" !
!
WARNING
* Blade (P/N 2610921689)
* Wrench (P/N 1619X04755)
** Rip Fence (P/N 2610914629)
(*= standard equipment)
(**= optional accessories)
552D9
36+8+
':/4-
58*/@+/4#
#/8+/@+9/433
3-6
6-8
8-10
10-12
12-16
18 16 16 14 0.75 .075 1.5 2.5
18 16 14 12 0.75 1.0 2.5 4.0
18 16 14 12 0.75 1.0 2.5 4.0
16 16 14 12 1.0 2.5 4.0 —
14 12 —— ————
25 50 100 150 15 30 60 120
58*+4-:./4++: 58*+4-:./4+:+89
+8</)+
8+<+4:/<+3'/4:+4'4)+
6+8,583+*(? ;4';:.58/@+*
6+89544+23'? 8+9;2: /4 3/962')/4- 5,
/4:+84'2 =/8+9'4* )53654+4:9 =./).
)5;2* )';9+ 9+8/5;9 .'@'8* We
recommend that all tool service be performed
by a Skil Factory Service Center or Autho rized
Skil Service Station.
!
Your Skil tool has been properly lubricated
and is ready to use. It is recommended that
tools with gears be regreased with a special
gear lubricant at every brush change.
!
The brushes and commutator in your tool have
been engineered for many hours of dependable
service. To maintain peak efficiency of the motor,
we recommend every two to six months the
brush es be examined. Only genuine Skil
replace ment brushes specially designed for your
tool should be used.
Bearings which become noisy (due to heavy
load or very abrasive material cut ting) should
be replaced at once to avoid overheating or
motor failure.
2+'4/4-
5 '<5/* '))/*+4:9 '2='?9
*/9)544+): :.+:552,853
:.+ 65=+8 9;662? (+,58+ )2+'4/4- 58
6+8,583/4-'4?3'/4:+4'4)+ The tool may
be cleaned most effectively with compressed
dry air. 2='?9 =+'8 9',+:? -5--2+9 =.+4
)2+'4/4-:5529=/:.)5368+99+*'/8
Ventilation openings and switch levers must
be kept clean and free of foreign matter. Do
not at tempt to clean by inserting pointed
objects through openings.
+8:'/4 )2+'4/4- '-+4:9
'4* 952<+4:9 *'3'-+
62'9:/)6'8:9 Some of these are: gasoline,
carbon tetrachlo ride, chlo rinated cleaning
solvents, ammonia and house hold detergents
that contain ammonia.
Blades become dull even from cutting regular
lumber. If you find yourself forcing the saw
forward to cut instead of just guid ing it through
the cut, chances are the blade is dull or coated
with wood pitch.
When cleaning gum and wood pitch from
blade, unplug the saw and remove the blade.
Remember, blades are designed to cut, so
handle carefully. Wipe the blade with kerosene
or similar sol vent to remove the gum and pitch.
Unless you are experienced in sharpening
blades, we recommend you do not try.
!
WARNING
'/4:+4'4)+
!
WARNING
!
CAUTION
>:+49/5458*9
The use of any other acces so ries not specified in this manual may create a hazard.
!
WARNING
SM 1619X08870_SPT67W 7/24/14 2:21 PM Page 14