2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V IMPORTANT: Read Before Using 2017/10/16 IMPORTANT : Lire avant usage 17:30 页 1 IMPORTANTE: Leer antes de usar Operating/Safety Instructions Consignes d’utilisation/de sécurité Instrucciones de funcionamiento y seguridad SPT70V Call Toll Free for Consumer Information & Service Locations Pour obtenir des informations et les adresses de nos centres de service après-vente, appelez ce numéro gratuit Llame gratis para obtener información para el
017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 2 General Power Tool Safety Warnings Read all safety warnings, instructions, illustrations and specifications ! WARNING provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 3 repaired before use. Many accidents are caused by poorly maintained power tools. correct power tool will do the job better and safer at the rate for which it was designed. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Keep cutting tools sharp and clean.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 4 last the life of the saw. If the switch should fail in the “OFF” position, the saw may not start. If it should fail while the saw is running, the saw may not shut off. If either occurs, unplug the saw immediately and do not use until repaired. center the saw blade in the kerf and so that the saw teeth are not engaged into the material.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 5 The lower guard may be retracted manually only for special cuts such as “plunge cuts” and “compound cuts”. Raise the lower guard by the retracting handle and as soon as the blade enters the material, the lower guard must be released. For all other sawing, the lower guard should operate automatically. backwards over your hand. Do not use the saw with an excessive depth of cut setting.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 6 Symbols IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 7 Symbols (continued) IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. This symbol designates that this tool is listed by Underwriters Laboratories. This symbol designates that this component is recognized by Underwriters Laboratories.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 8 Functional Description and Specifications Disconnect the plug from the power source before making any ! WARNING assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. SPT70V Circular Saw FIG.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 9 Functional Description and Specifications Disconnect the plug from the power source before making any ! WARNING assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. SPT70V Circular Saw FIG.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 10 Assembly ATTACHING THE BLADE Disconnect the plug from ! WARNING the power source before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V Inner washer has two sides (Fig. 4). Washer on one side has arbor size marked 1" (25.4 mm). Other side of the washer has arbor size marked as 25.0 mm. Check the hole size of the blade and use the proper size of the washer. Mounting a blade with 1" (25.4mm) arbor to the 25.0 mm side of the washer can cause dangerous vibrations. 2017/10/16 17:30 页 11 FIG. 4 MOUNTING ADJUSTABLE AUXILIARY HANDLE Disconnect plug from power source.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 12 90° CUTTING ANGLE CHECK Disconnect plug from power source. Set foot to maximum depth of cut setting. Loosen the front and back adjustments screws. Loosen the front and the back bevel adjustment lever. Place the carpenter's square between the blade and the foot. Adjust the angle of the foot until the angle between the foot and the blade is true 90°. Tighten the front and back bevel levers.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V WRENCH USAGE Wrench provided has several functions other than loosening/tightening the blade bolt (Fig. 10). 2017/10/16 17:30 页 13 FIG. 10 1. Loosening/tightening blade bolt (1/2” wrench). 2 2. Loosening/tightening oil plug (1/2” wrench). 3. Loosening/tightening brush caps (slotted driver). 1 4. Loosening/tightening bevel/depth levers when levers are over tightened or additional tightening is needed (9/16” wrench).
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V SWITCH When starting the tool, ! WARNING hold it with both hands. The torque from the motor can cause the tool to twist. To turn tool “ON”, squeeze the trigger switch. To turn the tool “OFF”, release the trigger switch, which is spring loaded and will return to the off position automatically. Your saw should be running at full speed BEFORE starting the cut, and turned off only AFTER completing the cut.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V CUTTING LARGE SHEETS Large sheets and long boards sag or bend, depending on support. If you attempt to cut without leveling and properly supporting the piece, the blade will tend to bind, causing KICKBACK and extra load on the motor (Fig. 13). 2017/10/16 17:30 页 15 FIG. 13 Support the panel or board close to the cut, as shown in (Fig. 14).
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 16 Maintenance To avoid accidents always disconnect the tool from the power supply ! WARNING before cleaning or performing any maintenance. Service Preventive maintenance ! WARNING performed by unauthorized per so n nel may result in misplacing of internal wires and components which could cause serious hazard.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V CARE OF BLADES Blades become dull even from cutting regular lumber. If you find yourself forcing the saw forward to cut instead of just guiding it through the cut, chances are the blade is dull or coated with wood pitch. 2017/10/16 17:30 页 17 When cleaning gum and wood pitch from blade, unplug the saw and remove the blade. Remember, blades are designed to cut, so handle carefully.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 18 Trouble Shooting Read instruction manual first! Remove plug from the power source before ! WARNING making adjustments or assembling the blade. PROBLEM REMEDY PROBLEM REMEDY PROBLEM REMEDY PROBLEM REMEDY PROBLEM REMEDY PROBLEM REMEDY TROUBLE: SAW WILL NOT START 1. Power cord is not plugged in. 2. Power source fuse or circuit breaker tripped. 3. Cord damaged. 4. Burned out switch. 5. Trigger does not turn tool on.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 56 LIMITED WARRANTY OF SKILSAW® PROFESSIONAL PORTABLE AND PROFESSIONAL BENCHTOP POWER TOOLS DESIGNATED WITH A MODEL NUMBER BEGINNING WITH SPT Chervon North America ("Seller") warrants to the original purchaser only, that all SKILSAW professional portable and benchtop power tools designated with a model number beginning with SPT, will be free from defects in material or workmanship for a period of one year from date of purchase.
