Instruction Manual
14
★ Tool does not operate
- kickback brake is activated -> pull hand guard S 2
back in position $a
- no power supply -> check power supply (power cable,
circuit breakers, fuses)
- plug not connected -> connect plug
- extension cord damaged -> replace extension cord
★ Tool operates intermittently
- on/o switch defective -> contact dealer/service
station
- internal wiring defective -> contact dealer/service
station
- extension cord damaged -> replace extension cord
★ Dry chain
- no oil in reservoir -> rell oil
- vent in oil reservoir cap clogged -> clean cap
- oil passage clogged -> clean oil passage outlet
★ Brake does not stop chain
- kickback brake/run-down brake defective -> contact
dealer/service station
★ Chain/chain bar overheats
- no oil in reservoir -> rell oil
- vent in oil reservoir cap clogged -> clean cap
- oil passage clogged -> clean oil passage outlet
- chain is overtensioned -> adjust chain tension
- dull chain -> sharpen chain or replace
★ Tool vibrates abnormally
- chain tension too loose -> adjust chain tension
- dull chain -> sharpen chain or replace
- chain worn out -> replace chain
- chain teeth are facing in the wrong direction ->
reassemble with chain in correct direction
ENVIRONmENT
• Donotdisposeofelectrictools,accessoriesand
packagingtogetherwithhouseholdwastematerial
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 8 will remind you of this when the need for
disposing occurs
DEClARATION OF CONFORmITY
• We declare under our sole responsibility that the product
described under “Technical data” is in conformity with the
following standards or standardization documents: EN
60745, EN 61000, EN 55014, in accordance with the
provisions of the directives 2004/108/EC, 2006/42/EC,
2000/14/EC, 2011/65/EU
• Technicalfileat: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
¹ÊÁÂÆÎ¹Æ¼½ÊÇǾ¼½Æ
ȽʹÌÁÇÆËŵÆ¿Áƽ½ÊÁÆ¿
ÍÊÇȽƓˁ˅ʿ˂ʽ¼¹Ɠ
Ĺ¾ÁÂÿʹ¹¾
ÈÈÊÇιĹƹ¿½Ê
30.07.2013
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 87 dB(A) and the sound
power level 107 dB(A) (standard deviation: 3 dB), and the
vibration 4.7 m/s² (hand-arm method; uncertainty K = 1.5
m/s²)
• Measured in accordance with 2000/14/EC (EN/ISO
3744) the guaranteed sound power level LWA is lower
than 110 dB(A) (conformity assessment procedure
according to Annex V)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for dierent applications, or with dierent
or poorly maintained accessories, may signicantly
increase the exposure level
- the times when the tool is switched o or when it is
running but not actually doing the job, may signicantly
reduce the exposure level
! protectyourselfagainsttheeffectsofvibration
bymaintainingthetoolanditsaccessories,
keepingyourhandswarm,andorganizingyour
workpatterns
Tronçonneuseàchaîne 0780
INTRODUCTION
• L’outil électrique est conçu pour scier le bois, comme par
ex. les poutres en bois, les planches, les branches, les
tronçons ainsi que pour abattre des arbres; il peut être
utilisé pour des coupes dans et contre le sens des bres
du bois
• Cet outil n’est conçu pour un usage professionnel
• Vériez que le conditionnement contient toutes les
pièces présentées dans le schéma 2
• Lorsque des pièces manquent ou sont endommagées,
veuillez contacter votre distributeur
• Lisezattentivementcemanueld’instructionavant
d’utiliserl’outiletconservez-lepourpouvoirvousy
référerultérieurement3
• Prêtezattentionauxconsignesdesécuritéetaux
avertissements;nepassuivrecesinstructionspeut
entraînerdesgravesblessures