Specifications

6

High-pressure washer 0760
INTRODUCTION
• This tool has been designed for cleaning areas and
objects outside the house, vehicles and boats
• This tool is intended for domestic use only and is not
designed to operate with water from sources other than a
watertap
• This tool is not intended for professional use
• Readthisinstructionmanualcarefullybeforeuse
andsaveitforfuturereference3
• Payspecialattentiontothesafetyinstructionsand
warnings;failuretofollowthesemayresultin
seriousinjury
• Check whether the packaging contains all parts as
illustrated in drawing 2
• When parts are missing or damaged, please contact your
dealer
TECHNICALSPECIFICATIONS1
Working pressure (P) 7 MPa
Maximum working pressure (Pmax) 10 MPa
Inlet pressure 0 - 0,6 MPa
TOOL ELEMENTS 2
A Trigger lock
B Trigger
C Inlet connector
D Water inlet
E Water lter
F Mains switch
G Spraying nozzle
H Detergent bottle
J Detergent nozzle
K Spray lance
L Hand gun
M Cleaning needle
N Storage rail (screwsnotsupplied)
P Storage strap (2)
Q High-pressure hose
R Water outlet
S Ventilation slots
T Connection for storage straps
SAFETY
GENERAL
• Use the tool and its accessories in accordance with this
instruction manual and in the manner intended for the
tool; use of the tool for operations, dierent from those
normally expected to be performed by the tool, could
result in a hazardous situation
• Neverdrawinsolvent-containingliquids,undiluted
acidsorsolvents(e.g.petrol,paintthinners,heating
oil); these liquids produce a highly ammable, explosive
and toxic sprayed vapour and they also corrode the tool
components
• Only use the tool when the ambient temperature is
between 0°C and 40°C
• Startworkingonlywhentoolandoperating
equipmentareinperfectconditionandsafeto
operate
• Be aware of the kickback forces that occur when starting
the high-pressure washer; hold hand gun and spray
lance rmly and take a secure stance
• Never clamp the trigger in position during operation
• Neverdirectthewaterjettowardsotherpeople,
animals,liveelectricalequipmentorthetoolitself4
• Never leave the tool unattended while the motor is
running
• Do not operate the tool in potentially explosive locations
• Alwaysswitchofftool,disconnectplugfrompower
source,andensurethereisnowaterpressurein
toolandhandgunbeforeadjusting,cleaningor
changingaccessories
PERSONALSAFETY
• Thistoolisnotintendedforusebypersons
(includingchildren)withreducedphysical,sensory
ormentalcapabilities,orlackofexperienceand
knowledge,unlesstheyhavebeengiven
supervisionorinstructionconcerninguseofthe
toolbyapersonresponsiblefortheirsafety
• Ensurethatchildrendonotplaywiththetool
• Wear suitable protective clothing to protect against
splashing water
• Donotusethetoolwithotherpersonsinthevicinity
unlesstheywearprotectiveclothing
• Do not spray materials containing asbestos and other
materials which contain substances which are hazardous
to your health
• Only clean tyres/tyre valves from a minimum distance of
30 cm to prevent damaging them (damaged vehicle tyres
may lead to fatal accidents)
• Donotdirectthewaterjetagainstyourselforothers
inordertocleanclothesorfootwear
WATERSUPPLY
• Onlyusethehigh-pressurehoseandcoupling
suppliedwiththetool
• Replace a damaged high-pressure hose immediately
(with identical specications)
• Do not kink or drive a motor vehicle over the high-
pressure hose
• Do not expose the high-pressure hose to sharp edges or
corners
• Ensure that all connecting hoses have properly sealed
joints
• Beawarethatthesprayedwatergeneratedbythe
toolisnotdrinkable
• According to the applicable regulations, the tool must
never be used on the drinking water net without a system
separator 5; use a suitable system separator as per
EN 12729 type BA
ELECTRICALSAFETY
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
• Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum