Owner's Manual

ManualsBrandsSiriusXM ManualsCar Audio & VideoXM Onyx EZ

1

2

3

4

5

6

7

8

9

Table Of Contents

L

£.

.15

..

£&.

.:

u

j

Find a Location for

Onyx

EZ and Mount

it

Select

either

the

Dash Mount

method

or

the

Vent

Mount

method

for

your

Onyx

EZ.

You

will

need

a

phillips-head

screwdriver

to

complete

the

installation.

• IMPORTANT!

To

make the

cable

connections easier, wait until after you have connected

all

the

cables

to the dock before you attach the dock to

the

dash or to a vent.

Dash

Mount

Method:

•

IMPORTANT:

The air temperature needs to

be

at

least

60°F

to

install

the Dash Mount.

If

needed

, turn on the

heater

in

your vehicle.

A.

Select

a

flat

surface

for

the

Dash

Mount

with

ample

room

for

Onyx

EZ.

Avoid

mounting

on

leather

surfaces. Choose a location

that

doesn't

interfere

with

the

driver's vision

or

access

to

driving

controls,

one

that

won't

interfere

with

the

deployment

of

airbags

or

other

safety

equipment,

and

makes

Onyx

EZ

easily accessible

for

operation.

(Airbag

locations

are

typically

marked

with

"SRS"

logos.)

B.

Orient

the

adhesive

foot

so

that

Onyx

EZ is

easily

accessible.

Loosen

the

knob

and

adjust

the

adhesive

foot

to

position

1

or

2,

and

then

tighten

it

Knob

Adhesive

Foot

~~)

w;r;

)

J:

C.

Attach

the

Dash

Mount

to

the

PowerConnect

Vehicle

Dock

using

the

4

provided

screws.

D.

Before

you

attach

the

Dash

Mount

to

the

dash

,

skip

ahead

and

finish

the

remainder

of

the

vehicle

installation

so

that

the

cables

are

attached

to

the

dock.

E.

Once

the

cables

have

been

attached

to

the

dock,

clean

the

mounting

surface

in

the

vehicle

with

the

alcohol

preparation

pad

and

let

it

dry

thoroughly.

F.

Once

the

surface

is dry,

remove

the

adhesive

liner.

Press

and

hold

the

Dash

Mount

in

place

for

30

seconds.

Allow

the

adhesive

to

cure

for

2-4

hours.

G.

You can

tilt

the

dock

mounting

plate

in

your

preferred

direction.

Dock

Mounting~

0 0

Vent

Mount

Method:

A.

Select

a

vent

with

ample

room

for

Onyx

EZ,

one

that

won't

interfere

with

the

deployment

of

airbags

or

other

safety equipment, and makes

Onyx

EZ

easily accessible

for

operation.

(Airbag

locations

are

typically

marked

with

"SRS" logos.)

B.

Some

vents

have recessed louvers. If

yours

are recessed,

remove

the

regular

vent

clamps

and

install

the

extended

vent

clamps.

C.

Attach

the

Vent

Mount

to

the

PowerConnect

Vehicle

Dock

using

the

4

provided

screws.

D.

Before

you

attach

the

Vent

Mount

to

the

vent,

skip

ahead

and

finish

the

remainder

of

the

vehicle

installation

so

that

the

cables

are

attached

to

the

dock.

E.

Once

the

cables

have

been

attached

to

the

dock

,

install

the

Vent

Mount

onto

the

vehicle

vent

(Note

that

for

clarity

the

illustrations

below

do

not

show

the

Vehicle

Dock

attached

to

the

Vent

Mount)

i.

Insert

the

vent

mount

into

the

vent

opening.

ii.

Push

until

hooked

on

the

rear

of

the

vent

louver.

Rest

the

foot

against

the

bottom

of

the

vent

iii.

If

necessary,

adjust

the

tilt

of

the

Vent

Mount

by

repositioning

the

foot

to

a

different

tilt

adjustment

hole

.

II

Ill

TILT/

ADJUSTMENT

HOLES

Vent