Quick Start Guide

ManualsBrandsSiriusXM ManualsCar Audio & VideoDock & Play satellite + streaming radio with vehicle kit (subscription sold separately by SiriusXM)

AUDIOANT PWR FM

AUDIOANT PWRFM

A. B.

Speciﬁcations

System

Power Requirements: 9-16 V DC,500 mA (max)

Operating Temperature: -4°F to +140°F (-20°C to +60°C)

Audio Output: 1.0 V

rms

(max)

Tour Radio

Dimensions: 4.7 in (W) x 2.9 in (H) x 0.7 in (D)

119 mm (W) x 74 mm (H) x 18 mm (D)

Weight: 5.0 oz (142 g)

Power

Connect Vehicle Dock

Dimensions: 4.0 in (W) x 2.4 in (H) x 1.2 in (D)

102 mm (W) x 61 mm (H) x 31 mm (D)

Weight: 1.6 oz (46 g)

Audio Connector: 1/8 in (3.5 mm) female

Antenna Connector: SMB male

Power

Connect Power Adapter

Dimensions: 3.7 in (W) x 1.7 in (H) x 1.3 in (D)

94 mm (W) x 43 mm (H) x 34 mm (D)

Weight: 2.4 oz (69 g)

Input / Output: 9-16 V DC / 5 V DC, 1.5 A

Cable Length: Approximately 4.6 ft (1.4 m)

Vehicle Antenna

Type: SiriusXM Magnetic Mount

Connector: SMB female, right angle

Cable Length: Approximately 23 ft (7.0 m)

Aux In Cable

Connectors: 1/8 in (3.5 mm) stereo male to

1/8 in (3.5 mm) stereo male

Cable Length: Approximately 4 ft (1.2 m)

Find a Location for Tour and Mount it

Dash Mount Method:

IMPORTANT: The air temperature needs to be at least 60°F to install the Dash Mount. If needed, turn on the

heater in your vehicle.

A. Select a flat surface for the Dash Mount with ample room for Tour. Avoid mounting on leather surfaces.

Choose a location that doesn’t interfere with the driver’s vision or access to driving controls, one that

won’t interfere with the deployment of airbags or other safety equipment, and makes Tour easily

accessible for operation. (Airbag locations are typically marked with “SRS” logos.)

B. Orient the adhesive foot so that Tour is easily accessible. Loosen the knob and adjust the

adhesive foot to position 1, 2, or 3, and then tighten it.

C. Attach the Dash Mount to the PowerConnect Vehicle

Dock using the 4 provided screws.

D. Before you attach the Dash Mount to the dash, skip

ahead and finish the remainder of the vehicle installation so that

the cables are attached to the dock.

E. Once the cables have been attached to the dock, clean

the mounting surface in the vehicle with the alcohol preparation

pad and let it dry thoroughly.

F. Once the surface is dry, remove the adhesive liner. Press and hold

the Dash Mount in place for 30 seconds. Allow the adhesive to

cure for 2-4 hours.

G. You can tilt the dock

mounting plate in your

preferred direction.

jump

direct

jump

direct

jump

direct

jump

Vent Mount Method:

A. Select a vent with ample room for Tour, one that won’t interfere with the deployment of airbags or

other safety equipment, and makes Tour easily accessible for operation. (Airbag locations are typically

marked with “SRS” logos.)

B. Some vents have recessed louvers. If yours are recessed, remove the regular vent clamps and

install the extended vent clamps.

C. Attach the Vent Mount to the PowerConnect Vehicle Dock

using the 4 provided screws.

D. Before you attach the Vent Mount to the vent, skip ahead

and finish the remainder of the vehicle installation so that the

cables are attached to the dock.

E. Once the cables have been attached to the dock, install

the Vent Mount onto the vehicle vent. (Note that for clarity the

illustrations below do not show the Vehicle Dock attached to

the Vent Mount.)

i. Insert the vent mount into the vent opening.

ii. Push until hooked on the rear of the vent louver. Rest the foot against the bottom of the vent.

iii. If necessary, adjust the tilt of the Vent Mount by repositioning the foot to a different tilt

adjustment hole.

direct

jump

ump

direct

Select either the Dash Mount method or the Vent Mount method for your Tour. You will need a phillips-head screwdriver to complete the installation.

IMPORTANT! To make the cable connections easier, wait until after you have connected all the cables to the dock before you attach the dock to the dash or to a vent.

Route the Antenna Cable

NOTE:

These instructions are for a sedan or coupe where the antenna is mounted above the

front windshield. The Tour User Guide (with Vehicle Kit) has detailed antenna cable routing

instructions for all types of vehicles. Go to www.siriusxm.com/guides for the User Guide.

A. Tuck the antenna cable under the

windshield rubber molding and run

it to the nearest corner.

B. Route the cable out of the molding

and into the rubber weather

stripping around the door opening.

C. Lift the weather stripping. Tuck and

run the cable inside it to the bottom

of the door opening. Replace the

weather stripping.

D. Pull the cable out and route it to Tour.

E. Plug the Magnetic Mount Antenna connector

into the silver ANT connector at the rear the

PowerConnect Vehicle Dock.

TIP: Include enough slack in your routing to accommodate open doors or the hood lid. Coil

any excess cable in a hidden location and keep it away from any vehicle pedals or controls.

Radio

Location

A. Mount the Magnetic Mount Antenna outside your vehicle, on a clean and

dry horizontal surface that will always face the sky.

B. Choose the location for the antenna according to your type of vehicle.

Center it between the left and right sides, and away from other antennas.

TIP: Use the Alcohol Prep Pad to clean the surface.

Sedans and Coupes

(above front windshield or rear window)

Pickups

(above front windshield)

Mount the Magnetic Mount Antenna

Start Here

PUSH

III III

Dash

Vent

Louver

Vent

HOOKED

TILT

ADJUSTMENT

HOLES

FO OT

Knob Adhesive Foot

Option 1 Option 2 Option 3

Dock Mounting Plate

Round End Orientation

Vent Mount Rear View

Slide Left Clamp to

Hole in Center

Pull Clamp Out

Towards Yo u

Insert Round End

of the Extended

Clamp in the

Center Hole

Slide Clamp to Left

to Complete

Installation

Repeat to Replac

Right Clamp

UDIO

ANT

UDIO

ANT

SUVs

(rear of roof)

Convertibles

(leading edge of trunk)

A. Insert the PowerConnect Power Adapter into your vehicle’s cigarette

lighter or power adapter socket. Plug the other end into the red PWR

connector at the rear of the PowerConnect Vehicle Dock.

B. Use the wire guide on the top of the dock to organize the wires

connected to the dock.

C. Place Tour into the dock.

Connect the PowerConnect Power

Adapter

Summary of content (2 pages)

PAGE 1
Start Here 1 2 Find a Location for Tour and Mount it Select either the Dash Mount method or the Vent Mount method for your Tour. You will need a phillips-head screwdriver to complete the installation. A. Mount the Magnetic Mount Antenna outside your vehicle, on a clean and dry horizontal surface that will always face the sky. IMPORTANT! To make the cable connections easier, wait until after you have connected all the cables to the dock before you attach the dock to the dash or to a vent.
PAGE 2
5 ? Finish the Installation Using the Setup Guide $65 Value Activation Fee and credit card required. See Offer Details on the Important Legal Information page. of our All Access Subscription Package 3 MONTHS FREE SERVICE With this radio, you’re eligible for For the remaining portion of the installation you will use the Setup Guide in the Radio.