Owner's Manual

1
Find a Location for Tour and Mount it
Dash Mount Method:
IMPORTANT: The air temperature needs to be at least 60°F to install the Dash Mount. If needed, turn on the
heater in your vehicle.
A. Select a flat surface for the Dash Mount with ample room for Tour. Avoid mounting on leather surfaces.
Choose a location that doesn’t interfere with the driver’s vision or access to driving controls, one that
won’t interfere with the deployment of airbags or other safety equipment, and makes Tour easily
accessible for operation. (Airbag locations are typically marked with “SRS” logos.)
B. Orient the adhesive foot so that Tour is easily accessible. Loosen the knob and adjust the
adhesive foot to position 1, 2, or 3, and then tighten it.
C. Attach the Dash Mount to the PowerConnect Vehicle
Dock using the 4 provided screws.
D. Before you attach the Dash Mount to the dash, skip
ahead and finish the remainder of the vehicle installation so that
the cables are attached to the dock.
E. Once the cables have been attached to the dock, clean
the mounting surface in the vehicle with the alcohol preparation
pad and let it dry thoroughly.
F. Once the surface is dry, remove the adhesive liner. Press and hold
the Dash Mount in place for 30 seconds. Allow the adhesive to
cure for 2-4 hours.
G. You can tilt the dock
mounting plate in your
preferred direction.
1
ju
m
p
F
M
m
e
n
u
2
3
4
5
6
7
8
9
0
di
r
ec
t
1
2
3
2
3
4
5
6
7
8
9
0
d
i
r
e
ct
j
u
m
p
F
M
m
e
n
u
1
2
3
4
5
6
7
8
9
0
d
i
r
e
c
t
j
u
m
p
F
M
m
en
u
1
1
2
3
4
5
6
7
8
9
0
di
r
e
ct
j
u
m
p
F
M
men
u
1
Vent Mount Method:
A. Select a vent with ample room for Tour, one that won’t interfere with the deployment of airbags or
other safety equipment, and makes Tour easily accessible for operation. (Airbag locations are typically
marked with “SRS” logos.)
B. Some vents have recessed louvers. If yours are recessed, remove the regular vent clamps and
install the extended vent clamps.
C. Attach the Vent Mount to the PowerConnect Vehicle Dock
using the 4 provided screws.
D. Before you attach the Vent Mount to the vent, skip ahead
and finish the remainder of the vehicle installation so that the
cables are attached to the dock.
E. Once the cables have been attached to the dock, install
the Vent Mount onto the vehicle vent. (Note that for clarity the
illustrations below do not show the Vehicle Dock attached to
the Vent Mount.)
i. Insert the vent mount into the vent opening.
ii. Push until hooked on the rear of the vent louver. Rest the foot against the bottom of the vent.
iii. If necessary, adjust the tilt of the Vent Mount by repositioning the foot to a different tilt
adjustment hole.
2
3
4
5
6
7
8
9
0
d
i
r
e
ct
j
ump
F
M
m
en
u
1
j
u
mp
F
M
m
e
n
u
2
3
4
5
6
7
8
9
0
di
re
c
t
1
Select either the Dash Mount method or the Vent Mount method for your Tour. You will need a phillips-head screwdriver to complete the installation.
IMPORTANT! To make the cable connections easier, wait until after you have connected all the cables to the dock before you attach the dock to the dash or to a vent.
Start Here
PUSH
I II III
Dash
Dash
Dash
Vent
Louver
Vent
Vent
HOOKED
TILT
ADJUSTMENT
HOLES
FOOT
Knob Adhesive Foot
Option 1 Option 2 Option 3
Dock Mounting Plate
Round End Orientation
Vent Mount Rear View
Slide Left Clamp to
Hole in Center
Pull Clamp Out
Towards You
Insert Round End
of the Extended
Clamp in the
Center Hole
Slide Clamp to Left
to Complete
Installation
Repeat to Replace
Right Clamp
UDIO
AN
T
FM
UDIO
AN
T
FM