COMMERCIAL INFORMATION FOR THE CONSUMER GB INSTALLATION, USE AND MAINTENANCE INSTRUCTION SEM1 - SEM2 - SEM5 - SEM7 - SEM8 - SEM10 TECHNICAL INFORMATION TYPE: FSED
- The symbol on the product or on its packaging indicates that this product may not be treated as household waste. lnstead it shall be handed aver to the applicable collection point far the recycling of electrical an d electron i c equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences far the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
GB Warnings! The air outlet of the appliance must not be connected to a flue which is used for exhausting other fumes from appliances, such as a central heating, boilers etc.. For the external exhausting of the fumes, comply with the regulations in force. Ventilate the room suitably according to the laws in force when the appliance is working together with gas, oil or coal burning appliances, at the same time. The motor of the peripheral exhausting group is powered by the cooker-hood placed in the kitchen.
SEM 1 (dis.1) - SEM 8 (dis.1a) Warning! The peripheral exhausting group (remote fitted extraction motor) is built in class II (symbol on the rating plate), therefore it must not be earthed. The appliance is designed to exhaust fumes and odours very silently and in the best way. It must be installed in the house and connected to the cooker-hood, which is in the kitchen (fig.
SEM 2 (fig.9) Warning! The remote fitted exhausting group (external motor) is built in class I plate, therefore it needs the earth connection. The appliance was designed to exhaust odours and vapours in the best way. The appliance is to be installed on the outside wall of the house and connetted to the cooker-hood which is in the kitchen (fig. 10) Installation: the mounting of the appliance is to be made by qualified technicians. Using the appropriate drilling jig (fig.
SEM 5 (fig.21) Warning! The remote fitted exhausting group (external motor) is built in class II (see symbol on the rating plate), therefore it must not be earthed. This model has been specifically studied to suction vapours and odours without noise.It should be installed outside and connected to the hood in the kitchen (fig. 22). Roof installation: make a 22 x 22 cm square opening on the roof, and then insert the lower part of the remote fitted exhausting motor (fig. 23).
SEM 7 (dis. 27) Warning! The remote fitted exhausting group (external motor) is built in class I plate, therefore it needs the earth connection. The appliance was designed to exhaust odors and vapors in the best way. The appliance is to be installed on the outside wall of the house and connected to the cooker-hood which is in the kitchen (fig. 28) Installation: the mounting of the appliance is to be made by qualified technicians. Using the appropriate drilling jig (fig.
SEM10 (fig. 31) SEM10 product has been designed to be installed under the kitchen cabinet, corresponding to the downdraft lower air outlet . This product can work only if it is used in combination with a downdraft equipped with external motor, manufactured by the same producer. The appliance has been designed to suck vapours and odours in an optimal and almost noiseless way . We recommend to use the product only in FILTERING MODE and to use a constant diameter piping of 150mm or similar sections.
WIRINC DIACRAM SEMI - SEMS Hotor type' GS50 MJHINAL PllfiER ' 300 Il AHPE:Rt (f) ' HAX J.
WIRING DIAGRAM SEM2 ' 5 " JJ D = ITIIJ • o 4-,Da. amoo 0 .
WIRINC DIACRAM SEM7 8 o @ Q Q (3 c ==tJ ©oD 11
WIRINC DIACRAM SEM8 '8 [j iii CII /D iii ::::. ::::.
WIRING DIAGRAM SEM10 CAPACITOR 13
SEM1 1 1a 2 3 4 5 14
6 7 8 15
SEM2 9 11 10 12 13 14 16
SEM5 21 22 23 24 25 26 17
l Mll l Mll 28 30 29 18
SEMlO i j 31 32 33 19
90004200486 GM 06/::_6
