User Guide
Table of Contents Introduction . . . . . . . . . . . . . . . . . . . 5 FM Presets . . . . . . . . . . . . . . . . . . . . . . . . 66 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Safety and Care Information . . . . . . . . . . 7 What’s in the Box? . . . . . . . . . . . . . . . . . . . 9 Stratus 6 Functions . . . . . . . . . . . . . . . . . 10 PowerConnect Vehicle Dock . .
Introduction 5
Introduction Features Congratulations, on your purchase of the Stratus 6! The Stratus 6 has these exciting features to enhance your overall experience: • Easy to read blue display: View artist name, song title, and channel information on an easy to read display. • A La Carte programming capability: Make individual channel selection. • Channel guide: View your individual channel lineup by category.
Safety and Care Information IMPORTANT! Always read and understand all the instructions to avoid injury to yourself and/or damage to your device. SIRIUS | XM Radio Inc. disclaims all responsibility for damage from data loss due to breakdown, repair, or other causes. • Do not expose to extreme temperatures (above 140ûF or below -4ûF, or above 60ûC or below -20ûC). • Do not expose to moisture. Do not use device near or in water. • Do not let any foreign matter spill into device. • Do not store in dusty areas.
Introduction WARNING! • Opening the case may result in electric shock. • If the liquid crystal fluid comes in contact with your skin, wipe the skin area with a cloth and then wash the skin thoroughly with soap and running water. If the liquid crystal fluid comes into contact with your eyes, flush the eyes with clean water for at least 15 minutes and seek medical care. If the liquid crystal fluid is ingested, flush your mouth thoroughly with water. Drink large quantities of water, and induce vomiting.
What’s in the Box? sel menu jump Stratus 6 Radio PowerConnect Vehicle Dock Aux In Cable Dash Mount PowerConnect Power Adapter Magnetic Mount Antenna and Rubber Tail Screws Vent Mount and Extended Vent Clamps Antenna & Dash Mount Alcohol Preparation Pads 9
Introduction Stratus 6 Functions Power Button Turn radio on and off. FM / Menu Button FM: Press to access and cycle through FM presets. Menu: Press and hold to access advanced features and configuration options; also when in configuration options, press and hold to return to main display screen. sel menu jump Jump Directly access traffic and weather of the 20 most congested cities. 10 Left and Right Arrows Search for channels by category.
PowerConnect Vehicle Dock Color-Coded Connections The PowerConnect Vehicle Dock has color-coded connectors to assist you in connecting the cables to the correct connector. Rear View PWR FM PWR (Red) Connection for PowerConnect Power Adapter. AUDIO FM (Blue) Connection for optional FM Direct Adapter (sold separately). AUDIO (Green) Connection for Aux In Cable or Cassette Adapter (sold separately). ANT ANT (Silver) Connection for the Magnetic Mount Antenna.
Vehicle Installation 13
Vehicle Installation Step 1: Choose a Location for Your Radio When installing the Stratus 6 in your vehicle, choose a location where it will not block your vision, interfere with the controls, or obstruct any air bags. The location should be easily accessible and provide good visibility of the display, and should not be located where it will be in direct sunlight, which will affect the visibility of the display screen.
Option 3 A. sel jump Option 4 Option 5 B. sel sel jump jump B.
Vehicle Installation Step 2: Install the Vent or Dash Mount Depending on your situation, you can either choose to use the Dash Mount or the Vent Mount. Installing the Dash Mount: CAUTION! The adhesive used on the Dash Mount may be difficult to remove. Do not install this mount on leather surfaces and make sure the air temperature is at least 60ûF (15ûC) during installation. 1 Locate a flat surface for the Dash Mount.
4 Clean the surface with the alcohol preparation pad and let it dry thoroughly. 5 Peel off the adhesive liner. Position, press, and hold the Dash Mount and PowerConnect Vehicle Dock in place for 30 seconds. IMPORTANT! Allow the Dash Mount adhesive to cure (dry) for a minimum of 2-4 hours before using the mount. The best adhesion occurs after 24 hours. 6 Knob The dock mounting plate can be tilted in different directions. Adjust as necessary for your particular vehicle.
Vehicle Installation Installing the Vent Mount: 1 Locate a vent with horizontal louvers sturdy enough to hold your PowerConnect Vehicle Dock and radio. 2 If the vent louvers in your vehicle are recessed, you may need to use the longer vent clamps with the Vent Mount. If so, Remove the shorter vent clamps and install the longer ones into the Vent Mount. Be sure to observe the orientation of the vent clamps as shown.
3 Attach the Vent Mount to the PowerConnect Vehicle Dock using the provided screws. 4 Push the Vent Mount onto the vehicle vent as shown (1) until it hooks on the rear of the vent louver (2). 5 Rest the foot against the bottom of the vent (2), and adjust the tilt of the Vent Mount by repositioning the foot to a different adjustment hole (3). 1 2 3 Dash Dash Dash HOOKED PUSH Vent Vent Louver FOOT Vent TILT ADJUSTMENT HOLES To remove the Vent Mount, push the mount into the vent.
Vehicle Installation Step 3: Mount the Magnetic Mount Antenna The Magnetic Mount Antenna contains a strong magnet which will stick to any metal part of your vehicle, but will not damage the vehicle. To install the Magnetic Mount Antenna: 1 Choose the best location for your antenna considering your own personal situation. Pay particular attention to any accessories that you may have like luggage racks and how frequently you may use them.
SUV: We recommend mounting the antenna at the rear of the roof as shown. Convertible: We recommend mounting the antenna at the leading edge of the trunk as shown. Pickup Truck: We recommend mounting the antenna above the front windshield as shown.
Vehicle Installation 2 3 22 Attach the Rubber Tail to the antenna and press the antenna cable into the Rubber Tail. The Rubber Tail will help to position the antenna the correct distance from the edge of the roof or trunk lid. Protective Material Clean the surface of the selected mounting location using the alcohol preparation pad and let it dry thoroughly.
TIP! Mount the antenna on the roof (for most vehicles) or trunk (for convertibles) where it has a clear view of the sky in all directions.
3” TIP! Mount the antenna on the roof where it has at least 3 inches of clear space around it. TIP! Use the supplied Rubber Tail to cover and protect the antenna cable. CAUTION! Don’t mount the antenna closer than 3 inches from the edge of the roof. Use the supplied Rubber Tail as a guide for judging proper length and correct positioning.
CAUTION! Don’t mount the antenna inside the vehicle, for example, on the dashboard. CAUTION! Don’t mount the antenna on any of the vehicle’s front, back or side pillars. CAUTION! Don’t mount the antenna close to a roof rack. Adjust the rack so it’s further away from the antenna or move the antenna closer to the center of the roof.
Vehicle Installation CAUTION! Don’t mount the Magnetic Mount Antenna close to another antenna. Mount it at least 3 inches away. TIP! Always be careful to include enough slack in your cable to accommodate open doors or trunk lids. Use things typically found around the home, like electrical tape, to secure cables in areas so that hinges do not pinch the cable with the door. Hide any excess cable in the trim.
Step 4: Route the Magnetic Mount Antenna Cable Before you begin routing the antenna cable, read these general instructions for how to route and hide the antenna cable. Then route your antenna cable according to the instructions which follow for your specific type of vehicle.
Vehicle Installation Route cable out from under rear windshield moulding and tuck into weatherstripping around trunk opening Avoid sharp bends by running cable through weatherstripping for several inches Pull weatherstripping from trunk opening Tuck cable into weatherstripping.
Bring cable out of weatherstripping and into trunk Route cable along trunk wall and into cabin through gap or conduit, along existing wiring harness Route cable along trunk wall and into cabin 29
Vehicle Installation Use a blunt plastic putty knife or similar blunt tool trim and tuck cable under trim.
Continue routing cable under carpet or console to radio location Pull carpet or mat back Coil excess cable under carpet or mat Bring cable out from trim Bring cable out from trim and route under carpet to dashboard or console TIP! Always be careful to include enough slack in your cable to accommodate open doors or trunk lids. Use things typically found around the home, like electrical tape, to secure cables in areas so that hinges do not pinch the cable with the door. Hide any excess cable in the trim.
Vehicle Installation • Sedan/Coupe With Antenna Placed at the Rear of the Roof: 1. Feed the antenna cable from the antenna underneath the rubber molding around the rear window. Use a blunt plastic putty knife or similar blunt tool to lift the rubber molding around the rear window and tuck the antenna cable underneath the molding. Route the antenna cable around and down the window to the lowest point. If your rear window does not have rubber molding, we recommend consulting a professional installer. 2.
area under the interior trim, towards the front of the vehicle. Use a blunt plastic putty knife or similar blunt tool to lift the plastic trim just enough to tuck the cable under underneath. Avoid side airbag locations on back pillars and above the doors. Airbag locations are marked with “SRS” logos. Be careful not to crimp or cut the cable. 5. Bring the cable out from the trim near the front of the cabin and route it under the carpet toward the dashboard or console.
Vehicle Installation • Sedan/Coupe With Antenna Placed at the Front of the Roof: 1. Feed the antenna cable from the antenna underneath the rubber molding around the windshield. Use a blunt plastic putty knife or similar blunt tool to lift the rubber molding around the windshield and tuck the antenna cable underneath the molding. Route the antenna cable around and down the windshield to the lowest point. 2.
• SUV: 1. Feed the antenna cable underneath the rubber weather stripping of the rear tailgate window/door and route the cable along the rear hatch. Lift the weather stripping from the opening and tuck the cable inside it, then replace the weather stripping. Pull the cable out from weather stripping and route it into the cabin under the interior trim. Avoid hinges or gears that could crimp or cut the cable. 2.
Vehicle Installation or controls. Secure the excess cable with wire ties (purchased separately). 4. Bring the end of the cable out at the PowerConnect Vehicle Dock location. Leave yourself enough cable so you can easily connect it to the antenna connector of the dock. 5. Continue with “Step 5: Connect the Magnetic Mount Antenna and PowerConnect Power Adapter” on page 39. • Convertible: 1. Bring the antenna cable from the antenna into the trunk at the front edge of the trunk lid.
Airbag locations are marked with “SRS” logos. Be careful not to crimp or cut the cable. 4. Bring the cable out from the trim near the front of the cabin and route it under the carpet toward the dashboard or console. Coil any excess cable in a hidden location, such as under the carpet, keeping it away from any vehicle pedals or controls. Secure the excess cable with wire ties (purchased separately). 5. Bring the end of the cable out at the PowerConnect Vehicle Dock location.
Vehicle Installation • Pickup Truck: 1. Use a blunt plastic putty knife or similar blunt tool to lift the rubber molding around the windshield and tuck the antenna cable underneath it. 2. Continue tucking the cable underneath the windshield molding around the windshield to the lowest corner. 3. At the lowest corner of the windshield, route the cable out of the windshield molding and into the rubber weather stripping around the door opening.
Step 5: Connect the Magnetic Mount Antenna and PowerConnect Power Adapter 1 Plug the Magnetic Mount Antenna into the silver ANT connector on the PowerConnect Vehicle Dock. 2 Insert the PowerConnect Power Adapter into your vehicle’s cigarette lighter or power adapter socket. 3 Plug the PowerConnect Power Adapter into the red PWR connector on the dock.
Vehicle Installation Step 6: Connect the Audio To play audio through your vehicle’s stereo or FM radio, decide on one of the following audio connection options: • Option 1: Best: Use the included Aux In Cable if your vehicle’s stereo system has an auxiliary input connection. Refer to your vehicle’s owners manual to find the location of the auxiliary input jack, or consult the vehicle dealer.
