User's Manual Part 1
Table Of Contents
- Instruction Book Introduction
- Customer Service
- Technical Assistance Center
- Sections 1-6
- Section 1 General
- Section 2 Functional Description
- 2.1 General
- 2.2 System Functional Overview
- 2.3 Main Functions
- 2.3.1 Signal Processing Unit (SPU) Sub-assembly
- Figure 2 - 2 Signal Processing Unit (SPU)
- Figure 2 - 3 Sirius Signal Processing Unit (SPU) Functional Block Diagram
- Figure 2 - 4 VSAT (L-Band) Receiver Panel
- Figure 2 - 5 Modulator Module
- Figure 2 - 6 Up-Converter Module Panel
- Figure 2 - 7 Controller Board Panel
- Figure 2 - 8 Main Controller Board Functional Block Diagram
- Figure 2 - 9 Uninterruptible Power Supply (UPS)
- 2.3.1 Signal Processing Unit (SPU) Sub-assembly
- 2.4 High Power Amplifier (HPA)
- 2.5 S-Band Output Filter
- 2.6 Output Coupler
- 2.7 Power Distribution
- 2.8 Junction Box Assembly
- Section 3 Installation
- 3.1 Introduction
- 3.2 Safety On Site
- 3.3 INSTALLATION OVERVIEW
- 3.4 SITE POWER
- 3.5 REPEATER UNPACKING AND INSPECTION
- 3.6 SUGGESTED TOOL LIST
- 3.7 ANTENNA INSTALLATION
- 3.8 REPEATER CABINET INSTALLATION
- 3.9 CABLE CONNECTIONS (see Figure 3 - 2)
- 3.10 POST-INSTALLATION INSPECTION/TEST
- 3.11 Post Installation Inspection/Test Form
- Section 4 Turn-Up and Testing
- 4.1 General
- 4.2 Test Equipment Required
- 4.3 Repeater Provisioning
- 4.4 Field Tests
- 4.5 Connect Repeater System to NMC
- 4.6 Field Test Report
- Section 5 Operation
- 5.1 GENERAL
- 5.2 Control and Communication
- 5.3 Modes of Operation
- 5.4 GRAPHICAL USER INTERFACE (GUI)
- 5.5 GUI Menu Descriptions
- 5.5.1 Status Sub-Menu Breakdown
- 5.5.2 Configuration (Config) Sub-Menu Breakdown
- Figure 5 - 7 GUI Main Menu Config Drop-Down Menu
- Figure 5 - 8 Config Modulator Sub-Menu
- Figure 5 - 9 Repeater ID Screen
- Figure 5 - 10 Modulator Mode Screen
- Figure 5 - 11 Overlay Screen
- Figure 5 - 12 Delays Screen
- Figure 5 - 13 Modulator IP Screen
- Figure 5 - 14 VSAT Screen
- Figure 5 - 15 Repeater Output Level Screen
- Figure 5 - 16 Coupler Screen
- Figure 5 - 17 GPS Screen
- Figure 5 - 18 Temperature Screen
- Figure 5 - 19 Repeater Operating Mode Screen
- Figure 5 - 20 PPP Dial In Parameters Screen
- Figure 5 - 21 PPP Dial Out Parameters Screen
- Figure 5 - 22 PPP Misc Parameters Screen
- Figure 5 - 23 Site Screen
- 5.5.3 Alarms Sub-Menu Breakdown
- 5.5.4 NMS Users Sub-Menu Breakdown
- 5.5.5 System Parameters Menu
- Figure 5 - 28 Access to System Parameters Sub-Menu
- Figure 5 - 29 System Parameters Identification Screen
- Figure 5 - 30 System Parameters Access Control Screen
- Figure 5 - 31 System Parameters Network Parameters Screen
- Figure 5 - 32 System parameters SNMP Parameters Screen
- Figure 5 - 33 System Parameters System Time Screen
- Figure 5 - 34 System Heartbeat Time Screen
- Figure 5 - 35 System Parameters System Reset Screen
- Figure 5 - 36 System Parameters Upgrade Screen
- Figure 5 - 37 Upgrade Dialog Box (Sheet 1 of 2)
- 5.6 COMMAND LINE INTERFACE (CLI)
- 5.7 REPEATER OPERATING PROCEDURES
- 5.8 CONTROLS, INDICATORS, and CONNECTORS
- 5.8.1 Signal Processing Unit (SPU) Controls and Indicators
- 5.8.2 High Power Amplifier (HPA) Controls and Indicators
- 5.8.3 Power Distribution Unit (PDU) Front Panel Controls
- 5.8.4 VSAT Receiver Rear Panel Connectors
- 5.8.5 Up-Converter Rear Panel Connectors
- 5.8.6 Modulator Rear Panel Connectors
- 5.8.7 Main Controller Rear Panel Connectors
OPERATION 3EM21522AAAA
DTR-0200-SA-SIRIUS Issue 1, March 2008
5-30
Figure 5 - 35 System Parameters System Reset Screen
The Upgrade screen allows the operator to upgrade system components by using the
Browse button to select the proper upgrade file (e.g.; Main Controller, Supervisor Con-
troller, VSAT Controller, Modulator [PPCO, PPCI, DSP, FPGA], Up-Converter, HPA).
After fi
le selection, click on “Start Download”. See Figure 5 - 36.
Figure 5 - 36 System Parameters Upgrade Screen