Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate recycling bin. 12” Compound Sliding Mitre Saw Double Bevel Never dispose of electrical equipment or batteries in with your domestic waste. If your supplier offers a disposal facility please use it or alternatively use a recognised re-cycling agent.
UK - DECLARATION OF CONFORMITY EU - DECLARATION OF CONFORMITY Declaration of Conformity Declaration of Conformity We We SIP (Industrial Products Ltd Gelders Hall Road Shepshed Loughborough Leicestershire LE12 9NH England As the manufacturer within the UK, England, Scotland & Wales, declare that the 12" Compound Sliding Mitre Saw - SIP Part. No. 01504 Conforms to the requirements of the following regulation(s), as indicated.
MAINTENANCE….cont CONTENTS GENERAL INSPECTION Cleaning and maintenance of this saw is mainly common sense some points for guidance are as follows: Regularly check that all the fixing screws are tight, particularly the outer flange. They may vibrate loose over time. The mains lead of the saw and any extension cord used should be checked frequently for damage. If damaged, have the mains lead replaced by an authorised service facility. Replace the extension cord if necessary.
MAINTENANCE….cont SAFETY SYMBOLS USED THROUGHOUT THIS MANUAL Danger / Caution: Indicates risk of personal injury and/or the possibility of damage. Warning: Risk of electrical injury or damage! Note: Supplementary Information. Loosen the locking nut on one of the bevel adjustment screws. Loosen the bevel lock (29). Pull out the bevel positive stop knob (30) whilst pushing the saw head to 45° either left or right depending on which adjustment screw has been loosened.
SAFETY INSTRUCTIONS….cont MAINTENANCE Danger: Always ensure that the saw is turned off and that the plug is disconnected from the mains supply before carrying out any adjustments, repairs or maintenance. This saw is set up at the factory and should need no adjustment; however time and careless use can affect the angles and some adjustment may be required.
SAFETY INSTRUCTIONS….cont REMOVE ADJUSTING KEYS AND WRENCHES: Form a habit of checking to see that keys and adjusting wrenches are removed from the tool before every use. SECURE THE WORKPIECE: Use clamps or a vice to hold the workpiece . This frees up both hands to operate the tool. DO NOT OVERREACH: Keep proper footing and balance at all times. DO NOT FORCE THE SAW: It will do the job better and more safely at the rate which it was designed.
OPERATING INSTRUCTIONS….cont SAFETY INSTRUCTIONS….cont Once the depth stop is set; the blade will not cut all the way through the workpiece (depending on the depth that it is set to). This will allow the operator to easily cut slots out of the workpiece if used in conjunction with the sliding function of the saw, it is advisable to check the cut depth on a scrap piece of wood. Do not use the saw until the table is clear of all tools, wood scraps, etc., except for the workpiece.
SAFETY INSTRUCTIONS….cont Ensure that the table base is properly secured so it will not move during operation. Make sure that all keys and wrenches are removed before switching on the saw. Keep hands out of path of saw blade, never reach around saw blade. Be sure that the blade does not come into contact with the table and / or table insert when the blade is in operation. Make sure the blade is clear of the workpiece before the switch is turned on.
OPERATING INSTRUCTIONS….cont SAFETY INSTRUCTIONS….cont Note: It is possible to remove the clamp assembly (18) by loosening the clamp assembly lock and moving it to the other side of the table. Make sure the clamp assembly lock is tight before using the clamp. at the operator. Always remember to switch off the laser on / off switch (2) after finishing a job, only turn the laser beam on when the workpiece is on the mitre saw table.
TECHNICAL SPECIFICATIONS OPERATING INSTRUCTIONS Part number 01504 Input voltage 230V ~ 50hz Power 2000 W No load speed 4500 rpm Blade Ø 305 mm Blade bore 30 mm Blade teeth 40 TCT Minimum blade thickness 2mm Maximum blade thickness 4mm Mitre table angles -45˚/ 0˚/45˚ Bevel Angles Up To 45° (Left & Right) Straight cut at 0˚x 0˚ 340mm x 102mm Mitre cut at 45˚x 0˚ 240mm x 102mm Left bevel cut at 0˚ x45˚ 340mm x 55mm Right bevel cut at 0˚ x45˚ 340mm x 40mm Left compound mitre cut
GETTING TO KNOW YOUR SAW….cont ELECTRICAL CONNECTION 26 This saw is fitted with a standard UK type 230v ~ plug. Before using the tool inspect the cable and plug to ensure that neither are damaged. If any damage is visible have the tool inspected / repaired by a suitably qualified person. If it is necessary to replace the plug a heavy duty impact resistant plug would be preferable. 25 24 23 28 27 This mitre saw is double insulated.
GUARANTEE GETTING TO KNOW YOUR SAW This SIP 12” double bevel saw is covered by a 12 month parts and labour warranty covering failure due to manufacturers defects. This does not cover failure due to misuse or operating the saw outside the scope of this manual - any claims deemed to be outside the scope of the warranty may be subject to charges Including, but not limited to parts, labour and carriage costs. Consumable items such as fuses and blades are not covered by the warranty.
