PUSH 2273 Instruction Manual
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety should always be followed, including the following: Read all instructions before using this sewing machine. DANGER - To reduce the risk of electric shock: 1. An appliance should never be left unattended when plugged in. 2. Always unplug this appliance from the electric outlet immediately after using and before cleaning. 3. Always unplug before re-lamping.
Congratulations As the owner of a new Singer sewing machine, you are about to begin an exciting adventure in creativity. From the moment you first use your machine, you will know you are sewing on one of the easiest to use sewing machines ever made. May we recommend that, before you start to use your sewing machine, you discover the many features and the ease of operation by going through this instruction book, step by step, seated at your machine.
List of contents Machine Basics Principle Parts of the Machine..............................................................................................................................................2/3 Connecting Machine to Power Source ....................................................................................................................................4 Two Step Presser Foot Lifter...........................................................................................................
Principal Parts of the Machine 1. Thread tension dial 2. Thread take-up lever 3. Thread cutter 1 7 8 4. Presser foot 5. Needle plate 9 2 6. Removable extension table/ accessory storage 7. Reverse sewing lever 10 3 8. Bobbin stopper 9. Stitch width dial 11 PUSH 4 10. Stitch length dial 11. Pattern selector dial 5 12. One step buttonhole lever 13.
Principal Parts of the Machine 14. Horizontal spool pin 15. Bobbin winding spindle 16. Hole for second spool pin 14 17. Handwheel 15 18. Power and light switch 16 19. Main plug socket 20. Bobbin thread guide 17 21. Upper thread guide 20 21 22 23 24 22. Face plate 23. Handle 24. Presser foot lifter 25. Foot speed control 26.
Connecting Machine to Power Source Connect the machine to a power source as illustrated. (1) This appliance is equipped with a polarized plug which must be used with the appropriate polarized outlet. (2) Attention: Unplug power cord when machine is not in use. A Foot control The foot control pedal regulates the sewing speed. (3) Attention: Consult a qualified electrician if in doubt of how to connect machine to power source. Unplug power cord when machine is not in use.
Two Step Presser Foot Lifter When sewing several layers or thick fabrics, the presser foot can be raised to a higher position for easy positioning of the work.
Accessories 1 Standard accessories Standard accessories (1) a. All purpose foot b. Zipper foot c. Buttonhole foot d. Button sewing foot e. Seam ripper/ brush f. Edge/ quilting guide g. Pack of needles h. Spool holder i. Bobbin (3x) j. L-screwdriver k. Oil bottle l. Darning plate a b 006806008 006905008 e d 006Q6A0150 006914008 g f i Optional accessories (2) (These 10 accessories are not supplied with this machine; they are however available as special accessories from your local dealer.) m.
Winding the Bobbin - Place thread and corresponding spool holder on to spool pin. (1/2) - Snap thread into thread guide. (3) - Wind thread counterclockwise around bobbin winder tension discs. (4) - Thread bobbin as illustrated and place on spindle. (5) - Push bobbin spindle to right. (6) 1 - Hold thread end. (7) 3 2 - Step on foot control pedal. (8) - Cut thread. (9) - Push bobbin spindle to left (10) and remove.
Inserting the Bobbin When inserting or removing the bobbin, the needle must be fully raised. a - Remove the extension table, then open the hinged cover. (1) - Pull the bobbin case tab (a) and remove the bobbin case. (2) - Hold the bobbin case with one hand. Insert the bobbin so that the thread runs in a clockwise direction (arrow). (3) 1 2 - Pull the thread through the slit and under the finger. (4) Leave a 6 inch tail of thread. - Hold the bobbin case by the hinged latch.
Thread Tension Upper thread tension Basic thread tension setting: "4" To increase the tension, turn the dial to the next number up. To reduce the tension, turn the dial to the next number down. A. Normal thread tension for straight stitch sewing. B. Thread tension too loose for straight stitch sewing. Turn dial to higher number. C. Thread tension too tight for straight stitch sewing. Turn dial to lower number. D. Normal thread tension for zig zag and decorative sewing.
Threading the Upper Thread This is a simple operation but it is important to carry out correctly as by not doing so several sewing problems could result. - Start by raising the needle to its highest point (1), and continue turning the handwheel counterclockwise until the needle just slightly begins to descend. Raise the presser foot to release the tension discs. Note: For safety, it is strongly suggested you turn off the power before threading. - Lift up the spool pin.
Automatic needle threader - Raise the needle to its highest position. - Press lever (A) down as far as it will go. - The threader automatically swings to the threading position (B). A B - Pass thread around thread guide (C). A C - Pass the thread in front of the needle around the hook (D) from bottom to top. D B C - Release lever (A). - Pull the thread through the needle eye.
Raising the Bobbin Thread Hold the upper thread with the left hand. Turn the handwheel (1) towards you (counterclockwise) lowering, then raising needle. Note: If it is difficult to raise the bobbin thread, check to make sure the thread is not trapped by the hinged cover or the Removable Extension Table. 1 Gently pull on the upper thread to bring the bobbin thread up through the needle plate hole. (2) Lay both threads to the back under the presser foot.
How to Choose Your Pattern The diagram on this page display the stitch patterns available on the machine. a b c Stitches in the top of the diagram are indicated on the Pattern Selector Dial in black. To select the patterns indicated with the black color, turn the Pattern Selector Dial. (d) Use the Stitch Length Dial (c) to adjust the stitch length as desired for the project. Use the Stitch Width Dial (b) to adjust the width of the stitch as desired.
Stitch Width Dial & Stitch Length Dial Function of stitch width dial The maximum zigzag stitch width for zigzag stitching is 5mm; however, the width can be reduced on any patterns. The width increases as you move zigzag dial from "0" - "5". (1) The Stitch Width Dial is also the control for the straight stitch infinite needle position. "0" position is full left, "5" is full right and between "2" and "3" is center needle position.
Sewing Straight Stitch To begin sewing, set the machine for straight stitch. (1) Place the fabric under the presser foot with the fabric edge lined up with the desired seam guide line on the needle plate. (2) Lower the presser foot lifter, and then step on the foot controller to start sewing.
Reverse Sewing To secure the beginning and the end of a seam, press down the reverse sewing lever (A). Sew a few reverse stitches. Release the lever and the machine will sew forward again. (1) A Removing the Work Turn the handwheel toward you (counterclockwise) to bring the thread take up lever to its highest position, raise the presser foot and remove work behind the needle and presser foot. (2) 1 2 B Cutting the Thread PUSH Pull the threads under and behind the presser foot.
Choosing Stretch Stitch Patterns The Stretch Stitch Patterns are indicated with a blue color on the Pattern Selector Dial. To select these stitches, turn the Pattern Selector Dial to the desired pattern. Then, turn the Stitch Length Dial to the indicator marked "S1". Though there are several stretch patterns, here are two examples: Straight Stretch Stitch Set the Pattern Selector Dial to " ". Used to add triple reinforcement to stretch and hardwearing seams.
Blind Hem For hems on curtains, trousers, skirts, etc. Blind hem for stretch fabrics. Blind hem for firm fabrics. Set the Stitch Length Dial with the range shown on the diagram at the right. Blind hems, however, are normally sewn with a longer stitch length setting. Set the Stitch Width Dial at a setting appropriate for the weight/type of fabric being sewn, within the range shown in the diagram on the right of the page.
Sew 1-step buttonholes Buttonhole sewing is a simple process that provides reliable results. However, it is strongly suggested to always make a practice buttonhole on a sample of your fabric and stabilizer. Making a Buttonhole 1. Using tailor's chalk, mark the position of the buttonhole on the fabric. 2. Attach the buttonhole foot and set the Pattern Selector Dial to " ". Set stitch length dial to " ". Set the stitch width at "5".
Sewing on Buttons Install the darning plate. (1) Change the all purpose foot to the button sewing foot. (2) Set the stitch length to "0". To sew a few securing stitches, set the machine for straight stitch, with the stitch width set at "0". Raise the needle out of the fabric. Set the machine for zigzag stitch , then set the width to number "3" - "5". Turn the handwheel to check that the needle goes cleanly into the left and right holes of the button.
Installing the Removable Extension Table Hold the removable extension table horizontally, and push it in the direction of the arrow. (1) To remove the extension table, pull it toward the left. PUSH 1 The inside of the removable extension table can be utilized as an accessory box. To open, flip cover down as shown.
Attaching the Presser Foot Shank Raise the presser bar (a) with the presser foot lifter. Attach the presser foot shank (b) as illustrated. (1) a a Attaching the presser foot Lower the presser foot shank (b) using the presser foot lifter, until the cut-out (c) is directly above the pin (d). (2) The presser foot (f) will engage automatically. e c b Removing the presser foot Raise the presser foot using the presser foot lifter. (3) Raise the lever (e) and the foot disengages.
Needle/ Fabric/ Thread Chart NEEDLE, FABRIC, THREAD SELECTION GUIDE NEEDLE SIZE FABRICS Lightweight fabrics-thin cottons, voile, silk, muslin, 9-11 (70-80) interlocks, cotton knits, tricots, jerseys, crepes, woven polyester, shirt & blouse fabrics. 11-14 (80-90) 14 (90) 16 (100) 18 (110) Medium weight fabrics-cotton, satin, kettlecloth, sailcloth, double knits, lightweight woolens. Medium weight fabrics-cotton duck, woolen, heavier knits, terrycloth, denims.
Darning Plate For certain types of work, (e.g. darning or free-hand embroidery), the darning plate must be used. Install the darning plate as illustrated. For normal sewing, remove the darning plate. For free-motion sewing it is recommended to use a darning/embroidery foot, available as an optional accessory from SINGER® retailers.
Inserting & Changing Needles Change the needle regularly, especially if it is showing signs of wear and causing problems. For best sewing results ® always use SINGER Brand Needles. D A Insert the needle as illustrated as follows: A. Loosen the needle clamp screw and tighten again after inserting the new needle. (1) B. The flat side of the shaft should be towards the back. C/D.Insert the needle as far up as it will go.
Changing the Bulb Disconnect the machine from the power supply by removing the plug from the main socket! Replace bulb with same type rated 10 watts (110-120V area) or 15 watts (220-240V area). - Loosen screw (A) as illustrated. (1) B A - Remove the face plate (B). - Unscrew the bulb and install a new one (C). (2) - Replace the face plate and tighten screw. PUSH ® Should there be any problem, consult your SINGER retailer.
Troubleshooting Guide Problem Cause Correction Upper thread breaks 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. Lower thread breaks 1. The bobbin case is not inserted correctly. 2. The bobbin case is threaded wrong. 3. The lower thread tension is too tight. 1. Remove and reinsert the bobbin case and pull on the thread. The thread should pull easily. 2. Check both bobbin and bobbin case. 3. Loosen lower thread tension as described. Skipped stitches 1. 2. 3. 4. The needle is not inserted correctly.
Please note that on disposal, this product must be safely recycled in accordance with relevant National legislation relating to electrical/electronic products. If in doubt please contact your retailer for guidance.
