Owner manual

CHECK CHART FOR PERFORMANCE
PROBLEMS
GENERAL PROBLEMS
Machine does not sew.
* Foot control is not connected.- See page 8.
* Power switch is turned off.- Turn on the switch.
Machine iams/knocks.
* Thread is caught in hook.- Clean hook (see page 38).
* Needle is damaged.- Replace needle (see page 24 - 25).
Fabric does not move.
* Presserfoot is not lowered - lower presserfoot.
* Stitch length is set at 0. - Set it at 1 to 4.
STITCHING PROBLEMS
Maohine skips stitches.
* Needle is not all the way up into needle clamp. - See page 24 - 25.
* Needle is bent or blunt. - Replace needle (see page 24 - 25).
* Machine is not threaded correctly. - See page 12.
* Thread is caught in hook. - Clean hook (see page 38).
Stitohes are irregular.
* Needle size is not correot for thread and fabric. - See page 24 - 25.
* Machine is not threaded correctly. - See page 12.
* Top thread tension is too loose. - See page 23.
* Fabric is being pulled or pushed against machine feeding action.
- Guide it gently.
* Bobbin has not been wound evenly. - Rewind bobbin.
Needle breaks.
* Fabric is being pulled or pushed against machine feeding action.
-Guide it gently.
* Needle size is not correct for thread and fabric. - See page 24 - 25.
* Needle is not all the way up into the needle clamp (See page 24 - 25).
THREAD PROBLEMS
Thread bunches.
* Top and bobbin threads are not drawn back under presser foot
before starting seam. - Draw both threads back under presserfoot
about 4 inches (10 cm) and hold until a few stitches are formed.
Needle thread breaks.
* Machine is not threaded correctly. - See page 12.
* Top thread tension is too tight. - See page 23.
* Needle is bent. - Replace needle (see page 24 - 25).
* Needle size is not oorrect for thread and fabrio - See page 24 - 25.
Bobbin thread breaks.
* Bobbin case is not threaded correotly. See page 11.
* Lint accumulates in bobbin case or hook. - Remove lint
(see page 38).
Fabric puckers.
* Top and bobbin thread tensions are too tight. - Adjust thread tensions
(see page 23).
* Stitch length is too long for sheer or soft fabric. - Shorten stitch length.
CUADRO DE EXAMEN PARA LOS PROBLEMAS
DE EJECUCION
PROBLEMAS GENERALES
Máquina no cose.
* El cordò eléctrico no está conectado (vea páina 8).
* El interruptor de energía no está conectado. - Ponerio en la posición
LOW o HIGH.
Máquina se atasca/rechina
* El hilo está enredado en la lanzadera. - Limpiar la lanzadera.
* La aguja se rompe. - Reponer la aguja (vea página 24 - 25).
La tela no se mueve.
* El prénsatelas no está bajado perfectamente. - Bajar el prénsatelas.
* Longitud del punto es demasiado corto. - Prolongar la longitud del
punto.
* La placa de cubierta de transportador se instala. - Quitar la placa de
cubierta de transportador.
PROBLEMAS DE PUNTO
La máquina salta puntos.
* La aguja no está fijada en la brida portaagujas (vea página 24 - 25).
* La aguja está torcida o obtusa. - Reponerla aguja (vea página 24-25).
* La máquina no enhebra correctamente (vea página 12).
Puntos son irrequiares.
* El número de la aguja no es oorrecto para el hilo ni el material (vea
página 24 - 25).
* La máquina no enhebra correctamente (vea página 12).
* La tensión del hilo superiores demasiado floja (vea página 23).
* El material está tirado o empujado contra la acción de alimentación.
- Guiario suavemente.
* La bobina no se ha devanado de un modo igual.- Redevanar la bobina.
La aquia se remope.
* El material está tirado o empujado contra el acción de alimentación.
* El número de la aguja no es correcto para el hilo ni el material (vea
página 24 - 25).
* La aguja no está fijada en la brida portaagujas (vea página 24 - 25).
PROBLEMAS DE HILO
Los hilos se juntan
* Los hilos superior e inferior no están sacados debajo del prénsatelas
antes de empezar a coser, - Sacar ambos hilo debajo del prénsatelas
unos 10 cm y mantener hasta que se formen unos pocos puntos.
La aquia se remope.
* La máquina no enhebra correctamente (vea página 12).
* La tensión del hilo superior es demasiado apretada (vea página 23).
* La aguja está torcida. - Cambiar la agja (vea página 24 - 25).
* El número de la aguja no es correcto para el hilo ni el material (vea
página 24 - 25).
El hilo inferior se rompe.
* La cápsula de portacanilla no enhebra correctamente (vea página 11 ).
* Las hilas se acumulan en la cápsula o en la lanzadera. - Quitarlas (vea
página 38).
La tela no queda plana.
* Las tensiones del hilo superior e inferior están demasiado apretadas.
- Ajustar las tensiones del hilo (vea página 23).
* La longitud del punto es demasiado largo para material fino o suave -
Acortar la longitud del punto.
40