2X series USER MANUAL Read the User Manual before operating the product, and keep the manual at a convenient place near the product. www.rize3d.
Safety Instructions Be sure to observe the followIng instructions when using the device. Warning: Failure to observe the instructions may lead to death or serious injury. Directly plug the power cord in the receptacle on the wall. Do not use extension cord. If the power cable or plug is worn or damaged, pull out the power plug. The exposure of the interior of the machine can cause electric shock or burns. Do not remove covers or screws other than specified in this manual. Please be cautious.
Before use Thank you for purchasing our product. This user manual contains detailed information about correct use of device and easy maintenance to maintain the optimal state, and to contribute to the rationalization of office work of your company. Carefully read the user manual before using the device and keep close at hand. In order to use device correctly and safely, please carefully note the precautions before use. Prohibition and limitation 1.
Contents Before using the Machine 1. Preface----------------------------------------------------------------------------------------------------------------------- 1 2. Conventions --------------------------------------------------------------------------------------------------------------- 2 Symbols ---------------------------------------------------------------------------------------------------------------------- 2 3.
Chapter 2 UI Menu Functions 1. UI Menu Function description------------------------------------------------------------------------------------- 2-2 1.
Chapter 3 Printing 1. Printing ------------------------------------------------------------------------------------------------------------------- 3-2 1.1 Printing from USB Flash Drive -------------------------------------------------------------------------------------- 3-2 1.2 Printing Via PC ---------------------------------------------------------------------------------------------------------- 3-8 1.
Installing Aluminum Bed ---------------------------------------------------------------------------------------------5-20 4.2 Filter Replacement ----------------------------------------------------------------------------------------------------5-20 4.3 Cartridge Replacement ----------------------------------------------------------------------------------------------5-24 4.
Before using the Machine 1. Preface This User Manual describes detailed explanations and points to note in connection with operating and using the machine. Please read the User Manual carefully before using machine, and keep it for reference purpose. Important - The content of the User Manual is subject to change without any prior notification.
Before using the Machine 2. Conventions Symbols This manual uses the following symbols and meanings. Warning - Indicates importance safety notes. Ignoring these notes could result in serious injury or death. Be sure to read these notes carefully for your safe operations of the machine. Caution - Indicates important safety notes. Ignoring these notes could result in minor injury, or damage to the machine or to property.
Before using the Machine 3. Safety Information Plug the power cord into a properly grounded outlet which is near and quickly accessible from the machine. Do not use or place the machine in wet or humid environment. Caution Hot Surface - The inside of the machine may be hot. To reduce the risk of injury from a hot component, allow some time to cool down.
Before using the Machine Caution Injuries - To prevent personal injuries or damages to the machine, you need to follow the below instructions before moving the machine. Do not open the front and top door during machine operation. Do not open the rear cover or touch any parts of the rear extruder unit during machine operation. When the power is on, do not let any of your body touch the machine except the bed.
Before using the Machine 4. Precautions 4.1 Installation Warning - Install the machine in a well ventilated area. You can small odor during machine operation. It should not be harmful; however, if the area of where the machine is located is not ventilated, make sure to ventilate the area appropriately time to time. Important - Install the machine with its vents spaced at least 10 cm away from walls and other equipments.
Before using the Machine 4.2 Moving the Machine Warning - Before moving the machine, be sure to unplug the power cord from the outlet. When moving the printer, it is recommended that two people lift and move the printer for safety. - Hold the bottom handles of the machine when moving it. Bend your knees enough to protect your spine when lifting the machine. - The unit is heavy. Make sure to carry with two or more people.
Before using the Machine 5. Consumables Handling Warning - Do not burn the Cartridge unit or filament. It may be a cause of big fire or burn by ignition. Caution - Keep them out of the reach of children. - If skin irritation occurs after touching the filament, please see a doctor. Important - Do not keep the cartridge unit in the following places.
Before using the Machine 5.3 Flexible When using flexible materials, clean the inside of the nozzle after the filament load. Even if the inside of the nozzle is cleaned, if the inside of the nozzle has debris, the nozzle may be clogged or the filament may be transported. (Refer to P. 5-3 “1.5 Cleaning the Inside of the Nozzle”.) Be careful because it is difficult to set the output condition compared with PLA and ABS materials. Warp or spider web may occur at output.
Before using the Machine 6. Instructions for Use Caution - The nozzle and the bed that are inside the machine are very hot during machine operation. Please be cautious not to touch the nozzle or the bed during removal of the printed objected or during inspection of the machine inside. It may become the cause of injuries or burns. - Never operate the machine in the way this manual does not specifically instruct.
Before using the Machine 7. Ventilation Caution - Use the machine in a place with good ventilation. If the machine is used in a place without good ventilation, this may be harmful for your health. Ventilate it on a regular basis. - Do not block vents. Inappropriate cooling may lead to high temperatures inside the machine. - In general, a new machine may produce small amount of gaseous components, so ensure good ventilation when the machine is used for the first time.
Before using the Machine 8. Notices ❖ Noise Emission Level The following are measured in accordance of ISO 7779 and reported to meet ISO 9296. Some modes may not be available in your purchased products.
Before using the Machine CAUTION Any changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment. ❖ Wireless LAN Specifications The wireless device may be affected by electromagnetic interference so it should not be used for life saving services.
Before using the Machine 9. Disposal of Used Battery Control board uses a Lithium battery. Please discard used batteries following the environmentally friendly procedure stated on the manufacturer guidelines. To replace batteries, please contact a qualified service engineer.
Before using the Machine 10. Wifi Module Disclaimer ❖ This module includes a Wifi module, compatible only with Sindoh 3DWOX models. Wifi module inside ❖ Precautions This Wifi module can cause radio interference, therefore it should not be used for any purposes related to human lives. Do not expose this product to water, humidity or liquid. Do not expose this product to direct light, hot temperature or fire.
Before using the Machine ❖ Precautions IEEE 802.11b : 2400MHz ~ 2484MHz Frequency IEEE 802.11g : 2400MHz ~ 2484MHz IEEE 802.11n(20MHz) : 2400MHz ~ 2483MHz IEEE 802.11n(40MHz) : 2400MHz ~ 2483MHz Antenna Power Density IEEE 802.11b : 10mW(10dbm)/MHz IEEE 802.11g : 10mW(10dbm)/MHz IEEE 802.11n(20MHz) : 10mW(10dbm)/MHz IEEE 802.11n(40MHz) : 10mW(10dbm)/MHz No. of Channels IEEE 802.11b : 14 IEEE 802.11g : 14 IEEE 802.11n(20MHz) : 14 IEEE 802.11n(40MHz) : 9 Modulation IEEE 802.11b : DSSS/CCK IEEE 802.
Before using the Machine 11. USB Memory Disclaimer ❖ FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Before using the Machine ❖ IC Identification on Class of ITE CAN ICES-3 (B)/NMB-3 (B) DECLARATION OF CONFORMITY Product name : USB Flash Drive Model name : 8GB-WJ004, 4GB-WJ004 FCC Rules : Tested to comply with FCC Part 15, Class A Operating Environment : For HOME OR OFFICE USE FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules.
2X Series USER MANUAL Preparations for Machine Operation 1
1 Preparations for Machine Operation 1. Machine Specifications 1.1 Printing Printing Method Fused Filament Fabrication Max. Print Length(mm) W(max):228, D(max):200, H(max):300 Print Layer Thickness Setting 0.05~0.4mm Basic Nozzle diameter 0.4mm Filament width 1.
1 Preparations for Machine Operation 2. Basic Components Please check all basic components are in the box. Caution - Please keep the box and packaging material; they are needed for product exchange or repair service. Cartridge 3D Printer USB Cable Reference Guide Scrapper Tube for Cleaning Power Cable USB Drive Nozzle Cleaner Spring Nozzle Cleaner Warning - The blades of the scrapper can be very sharp. Please be cautious. Please do not use for other than removing printables.
1 3. Preparations for Machine Operation Understanding the Device Parts 4 5 6 3 2 7 8 9 1 10 No. Part Name Description 1 Front door handle A handle to open the front door. 2 USB port Connect USB flash drive containing printing information and print directly from USB flash drive. 3 LCD Control panel Screen used to control printer. Caution - Usage of printer is recommended after removing the protection film on LCD control panel.
Preparations for Machine Operation 1 3 4 1 1 2 No. Part Name Description 1 Bed height adjustment Knob Used to level the Flexible bed. 2 Removable bed handle Used to assemble and dismantle Flexible bed 3 Bed heater Heats the printables' bottom surface to stabilize it on the bed. 4 Flexible bed (bed sheet) Seating space for Printable 3 1 2 5 4 No. Part Name Description 1 Body Main body of the nozzle part. 2 Fan 1 Cooling fan for extrusion.
1 Preparations for Machine Operation 4. Installation(Product connection, Cartridge Setup and Software installation) 4.1 Device Connection 1 On the rear side of the machine, connect the power cable to the power socket. Next, connect the power cable to the power outlet. 2 Press the power button, located on top of the machine. 3 After main menu is displayed on the LCD screen, install the cartridge (Refer to UI manual “LOAD”).
Preparations for Machine Operation 1 3 When installation of the file is complete, a pop-up window shows up as picture below. Press [Next] button to initiate the installation of 3DWOX Desktop program. 4 Choose the destination location of the file and press [Next] to proceed. 5 The file gets saved and the installation starts.
1 Preparations for Machine Operation 6 After all installation is complete, you can see that the “3DWOX Desktop” created on the desktop of your computer.
