Mambo Surface Prep Operating Manual Read before use and keep safe (800) 624-2408 (530) 626-9386 Fax (530) 626-5144 6686 Merchandise Way Diamond Springs, Ca 95619 www.sineqco.
Table of Contents 1.0 Technical Data Page 3 2.0 Safety Page 3 3.0 Safety Instructions Page 3 4.0 Maintenance Page 5 5.0 Use Page 7 6.0 Vacuum Unit Page 7 7.0 Trouble Shooting Page 8 8.
1.0 Technical data/technical description Power supply Power consumption No-load speed Sound pressure level Sound energy level Hand/Arm-Vibration Weight 110V 50 Hz 2300W 100 – 400 Strokes/min 56 dB(A) 69 dB(A) < 4,5 m/s² 155 lbs Comes with: Mambo Surface Prep, safety goggles and tool kit. 2.0 Safety The Sinclair Mambo Surface Prep is state of the art designed and meets all standard safety requirements. 3.0 Safety Instructions Disconnect the power supply before any maintenance is carried out.
For your won safety start work always at low speed, and then increase the speed. This is especially important, if the sub-floor condition or the discs used are not well known. CAUTION!!! Always wear ear and eye protectors! CAUTION!!! Using this machine without ear and eye protectors may jeopardize or harm your health. It may harm especially your ears and increase the risk of an accident.
3.4 Genuine Spare Parts Spare parts and accessories are manufactured uniquely for the Mambo Surface Prep. It must be emphasized that parts obtained from unauthorized sources must not be used. Sinclair Equipment Company cannot be held responsible for the performance of or any damage arising from the use of machines in which genuine spare parts have not been used. This is particularly important with milling discs. 4.0 Maintenance The Mambo Surface Prep is virtually maintenance free.
Use: - Mount discs or brushes as described above. - Put the handle in working position with the big lever (1) at the back. - We recommend to position the hand grip to the height of the users hip. - Lift the handle slightly, to make sure the machine stands horizontally. - Keep the safety switch (2) pressed. - Switch on the machine with one of the levers (3) located beneath the grip. - Release switch (2). Note: lever can only be actuated, if the handle is not in vertical position.
The table below is meant as a guiding principle for the user. Always test the optimum speed in each case. Always start at low speed and then increase the speed. Speed 160–200 200-300 300-400 Use Grinding screed and leveling compounds Grinding parquet, removing leveling compounds and adhesive residues Removing leveling compounds Recommended Disc Sand paper Carbide grinding disc and Milling disc Milling disc Always remove discs after work.
Mounting or changing the paper bags of the Vacuum Micropac Unit Paper bags are used for the vacuum unit Micropac. Replacement paper bags, 20 piece, Item # M13498. - - Release the 2 snap fasteners (B) and remove lid (C). Ensure inner cloth filter is clean. Ensure rubber molding (D) is firmly fitted around top rim of container. Gently open new dust bag and place in vacuum container. Slide flange (A) of the dust bag over inlet spigot (E) until secure. Replace and secure lid with 2 snap fasteners.
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 43 45 46 49 50 51 52 53 54 55 56 57 58 59 61 64 65 66 1 1 1 1 2 2 2 2 1 1 1 1 1 3 2 2 1 4 2 4 4 1 2 2 2 2 2 2 2 1 1 1 1 2 3 1 1 1 9 6 7 4 13 4 2 2 2 2 1 1 1 2 2 Back panel Support chain wheel Handle support Additional weight Cylindrical screw M10 x 70 Wheel hub Square nut Counter Sink Screw M8 x 14 Cylindrical screw M4 x 12 Lever (handle adjustment) Handle mounting Chain wheel Recessed grip Oval head screw M4
67 68 69 70 71 72 73 74 75 76 77 78 79 80 150 152 153 154 155 156 157 158 160 161 162 165 167 168 169 170 172 173 175 176 178 179 181 185 187 188 190 191 193 194 195 196 197 198 8 1 4 2 2 2 1 1 1 6 1 3 12 3 1 1 1 1 1 1 1 1 6 1 2 2 1 1 2 2 2 1 4 1 1 1 2 2 2 2 2 1 1 4 4 1 1 1 Screw 5/16" Plate Cylindrical screw M4 x 20 Connection Handle Clamping lever Intermediate flange Upper flange Lower flange Cache Coupling flange Distance washer Counter sunk screw M8 x 12 Counter sunk screw M8 x 18 Knob Two-hand switch
MAMBO HANDLE
SINCLAIR EQUIPMENT COMPANY’S tools are warranted to be free of defects in workmanship and materials for a period of one year from the date of original purchase. Should any trouble develop during this one year period, return the complete tool, freight prepaid, to SINCLAIR’S authorized Service Center. If inspection shows the trouble is caused by defective workmanship or materials, SINCLAIR EQUIPMENT COMPANY will repair, or, at its option, replace without charge.
12
