EN User Manual Dishwasher SSF6106W SSF6106X
Contents Safety information Safety instructions Control panel Programs Before first use Daily use 2 3 4 5 6 6 Hints and tips Care and cleaning Troubleshooting Technical information Warranty 9 10 10 12 12 Subject to change without notice. Safety information Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage.
by clients in hotels, motels, bed & breakfast and other residential type environments. Do not change the specification of this appliance. The operating water pressure (minimum and maximum) must be between 0.5 (0.05) / 8 (0.8) bar (kPa) Obey the maximum number of 13 place settings. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or a similarly qualified persons in order to avoid a hazard.
• • Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. Water connection • • • • Do not cause damage to the water hoses. Before connection to new pipes, pipes not used for a long time, where repair work has been carried out or new devices fitted (water meters, etc.), let the water flow until it is clean and clear.
Indicators Indicator Description Washing phase. It comes on when the washing phase operates. End indicator. Rinse aid indicator. It is always off while the program operates. Half Load indicator. Programs Program Degree of soil Type of load Program phases Consumption values 1) Duration (min) Energy (kWh) Water (l) Normal soil Crockery and cutlery • • • • Prewash Wash 50 °C Rinses Dry 129 0.77 11.6 Medium soil Mixed load • • • • Prewash Wash 65 °C Rinses Dry 100 - 120 1.3 - 1.
For any other questions regarding your dishwasher please refer to the service book provided with your appliance. Before first use 1. 2. 3. Fill the rinse aid dispenser. Open the water tap. Start a program to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets. Adding rinse aid 1 43 21 2 The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot rinse phase. Daily use 1. 2.
Reset With Reset you can cancel the running program . The appliance goes back to the Program selection mode. Starting a program Open the water tap, close the door, select a program, press .
1. Set the program. 2. Press 3. Press the related indicator comes on. to start the program. This option is available with , and . With this option you can wash a small load of tableware and cookware. The option decreases the program duration and the consumption of water and energy. Load both baskets and use less quantity of detergent. Opening the door while the appliance operates If you open the door while a program is running, the appliance stops.
Hints and tips General • The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • • • • • • • Remove larger residues of food from the dishes into the waste bin. Do not pre-rinse dishes by hand. When needed, use the prewash program (if available) or select a program with a prewash phase. Always use the whole space of the baskets.
Care and cleaning Warning! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. Cleaning the filters B A C • • • • Make sure that there are no residues of food or soil in or around the edge of the sump. Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides. Reassemble the filters (A) and (B).
Problem and alarm code Possible solution You cannot activate the appliance. • • Make sure that the mains plug is connected to the mains socket. Make sure that there is no a damage fuse in the fuse box. The program does not start. • • • Make sure that the appliance door is closed. Press Start. The appliance has started the procedure to recharge the resin inside the water softener. The duration of the procedure is approximately 5 minutes. The appliance does not fill with water.
Technical information Dimensions Width / height / depth (mm) 600 / 850 / 625 Electrical connection 1) Voltage (V) 220 - 240 Frequency (Hz) 50 Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 5.0 Off-mode (W) 0.50 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy (e.g.
3. 4. 5. 6. 7. any non-excludable statutory warranties in New Zealand. During the Warranty Period Electrolux or its ASC will, at no extra charge if your Appliance is readily accessible for service, without special equipment and subject to these terms and conditions, repair or replace any parts which it considers to be defective. Electrolux or its ASC may use remanufactured parts to repair your Appliance. You agree that any replaced Appliances or parts become the property of Electrolux.
FOR SERVICE or to find the address of your nearest authorised service centre in New Zealand Free call 0800 10 66 10 SERVICE NEW ZEALAND ELECTROLUX (NZ) Limited www.electrolux.co.nz (New Zealand only) FOR SPARE PARTS or to find the address of your nearest state spare parts centre in New Zealand Free call 0800 10 66 20 (New Zealand only) Environmental concerns dispose of appliances marked with the symbol with the household waste.
www.simpson.co.
