EN User Manual Dishwasher SSF6106W SSF6106X
Contents Safety information Safety instructions Control panel Programs Before first use 2 3 4 5 6 Daily use Hints and tips Care and cleaning Troubleshooting Technical information 6 9 10 11 12 Subject to change without notice. Safety information Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage.
• • • • • • • • • • • • Do not change the specification of this appliance. The operating water pressure (minimum and maximum) must be between 0.5 (0.05) / 8 (0.8) bar (kPa) Obey the maximum number of 13 place settings. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or a similarly qualified persons in order to avoid a hazard. Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position.
Water connection • • • • • • Do not cause damage to the water hoses. Before connection to new pipes, pipes not used for a long time, where repair work has been carried out or new devices fitted (water meters, etc.), let the water flow until it is clean and clear. Ensure that there are no visible water leaks during and after the first use of the appliance. If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket.
Indicators Indicator Description Washing phase. It comes on when the washing phase operates. End indicator. Rinse aid indicator. It is always off while the program operates. Half Load indicator. Programs Program Degree of soil Type of load Program phases Consumption values 1) Duration (min) Energy (kWh) Water (l) Normal soil Crockery and cutlery • • • • Prewash Wash 50 °C Rinses Dry 129 0.77 11.6 Medium soil Mixed load • • • • Prewash Wash 65 °C Rinses Dry 100 - 120 1.2 - 1.
Before first use 1. 2. 3. Fill the rinse aid dispenser. Open the water tap. Start a program to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets. Adding rinse aid 1 43 21 2 The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot rinse phase. Daily use 1. 2. Open the water tap. Set the correct program for the type of load and the degree of soil.
Adding multi-tablets 1 2 • Set the rinse aid dispenser to the lowest position. Program selection mode The appliance must be in Program selection mode to start a program. If the control panel does not show this condition, use the Reset function. Reset With Reset you can cancel the running program . The appliance goes back to the Program selection mode.
Open the water tap, close the door, select a program, press . Option Half load 1. Set the program. 2. Press 3. Press the related indicator comes on. to start the program. This option is available with , and . With this option you can wash a small load of tableware and cookware. The option decreases the program duration and the consumption of water and energy. Load both baskets and use less quantity of detergent.
At the end of the program 5 min The indicator comes on. If you do not deactivate the appliance within 5 minutes all indicators goes off. This helps to decrease energy consumption. Turn the knob to . Close the tap. For the better drying results keep the appliance door ajar for some minutes before you remove the dishes. Let the dishes cool down before you remove them form the appliance. Hot dishes are easily damaged.
3. Adjust the released quantity of rinse aid. Loading the baskets • Only use the appliance to wash items that are dishwasher-safe. Do not put in the appliance items made of wood, horn, aluminium, pewter and copper. Do not put in the appliance items that can absorb water (sponges, household cloths). Remove remaining food from the items. Make soft the remaining burned food on the items. Put hollow items (cups, glasses and pans) with the opening down. Make sure that cutlery and dishes do not bond together.
• • • Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides. Reassemble the filters (A) and (B). Put back the filter (A) in the flat filter (C). Turn it clockwise until it locks. An incorrect position of the filters can cause bad washing results and damage to the appliance Cleaning the spray arms Internal cleaning Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object.
Once you have checked the appliance, press problem occurs again, contact the Service. . If the For alarm codes not described in the table, contact the Service. The washing and drying results are not satisfactory Problem Possible solution There are whitish streaks or bluish layers on glasses and dishes. • There are stains and dry water drops on glasses and dishes. • • • • The dishes are wet. • • • The release quantity of rinse aid is too much. Adjust the rinse aid selector to a lower position.
Rating Plate Information for test institutes For all the necessary information for test performance, send an email to: info.test@dishwasher-production.com Mod. ... ... ... Prod. No. ... ... ... Ser. No. ... Write down the product number (PNC) that is on the rating plate. ENVIRONMENTAL CONCERNS dispose of appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office. Recycle materials with the symbol .
www.simpson.co.nz / www.simpson.com.
