MSDS
S
ET
Epoxy
-
Tie
®
Anchoring Adhesive
-
MATERIAL SAFETY DATA SHEET
PAGE
2
OF
6
Form T
-
SAS
-
SET
MSD09
V.
FIRE
-
FIGHTING MEASURE
S
Suitable
Extinguishing M
edia
:
Water fog,
carbon dioxide or dry chemical,
aq
ueous foam
.
Fire And Explosion Hazard:
Hazardous
decomposition products
may occur when material
s
polymerize at
t
emp
eratures above
500
o
F.
Do not allow run
-
off from fire fighting to enter drains or
water courses.
Fire Fighting Equipment
and
Wear full protective clothing and
self
-
contained breathing apparatus
for fire fighting.
Procedures:
Isolate fuel supply
from fire. Clear fire area of all non
-
emergency personnel. Use water
spray to cool fire
-
exposed surfaces and containers.
VI
.
ACCIDENTAL RELEASE MEASURES
Personal Precautions:
Use cautious judgment when cleaning up spill. Shut off leaks, if poss
ible without
personal risk. Wear suitable protective clothing, gloves and eye/face protection.
Evacuate personnel to safe areas.
Environmental Precautions:
Construct a dike to prevent spreading.
Keep out of sewers, storm drains, surface waters,
an
d soils.
Clean
-
up Methods:
Small spills
: Soak up with
absorbent material such as clay, sand or other
suitable non
-
reactive
material. Place in l
eak
-
proof
containers. Seal tightly
for
proper disposal.
Large spills
:
Approach suspected leak areas
with caution. Create a d
ike
or trench to
contain material.
Soak up with
absorbent material such as clay, sand or other
suitable
non
-
reactive
material. Place in l
eak
-
proof
containers. Seal tightly
for
proper disposal.
Additional
Information:
Not
ify
authorities if any exposures to the general public or environment occur or are
likely to occur. Dispose
in accordance with federa
l, state, and local regulations.
VII.
STORAGE AND HANDLING
Storage:
Keep away from: acids, oxidizers, he
at, or flames. Keep in cool, dry, well
-
ventilated area
in closed containers. Protect conta
iners from physical damage.
Handling:
To prevent
skin and eye
contact under the foreseeable conditions of use, wear
appropriate protective clothing and
safety eyewear. When handling, do not eat, drink, or
smoke. Wash thoroughly after handling. Avoid breathing fumes. Handle
in a well
-
ventilated work area.
VIII.
EXPOSURE
CONTROLS / PERSONAL PROTECTION
Protective Measure:
Wear appropriate personal p
rotective equipment.
Eye Protection:
Avoid
contact with eyes. Wear chemical splash goggles or safety glasses with side
shield.
Hand Protection:
Wear chemical
-
resistant gloves such as: Nitrile, neoprene, butyl.
Skin and Body Protection:
Wear chemical
-r
esistant gloves and other clothing as required to minimize contact.
Respirator Protection:
Not required for properly ventilated areas.
Exposure Limits:
COMPONENT
ACGIH
(TLV)
OSHA
(PEL)
BisPhenolA/Epichlorohydrin (Epoxy Resin)
N/E N/E
N-
buty
l glycidyl ether
25 ppm
25 ppm
Silica, crystalline quartz (airborne particulates of
respirable size)
0.1 mg/m
3
0.4 mg/m
3
Titanium dioxide (total dust)
10 mg/m
3
15 mg/m
3
IX
.
PHYSICAL
AND CHEMICAL
PROPERTIES
Form:
P
aste
Color
:
White
Odor:
Sweet
Vapor Pressure:
Not Volatile
Boiling Point
:
>500
F
(
> 260
C)
Freezing Point:
N/E
Flash Point
: >
250
o
F
(Op
en Cup
)