Specification

C-2013 © 2013 SIMPSON STRONG-TIE COMPANY INC. PRINTED 12/12
137
Plated Truss Connectors
HTU Face Mount Truss Hangers
Plated Truss Connectors
HGUQ Multi-Ply Girder Truss Hangers
See table footnotes on page 136.
Alternate Allowable Loads (
1
⁄ 2 " Maximum Hanger Gap)
HGUQ28-2
1. Uplift loads have been increased for wind or earthquake loading with no
further increase allowed. Reduce where other loads govern.
2. Wind (160) is a download rating.
3. Truss chord cross-grain tension may limit allowable loads in accordance with
ANSI/TPI 1-2007. Simpson Strong-Tie
®
Connector Selector™ Software includes
the evaluation of cross-grain tension in its hanger allowable loads. For additional
information, contact Simpson Strong-Tie.
4. Simpson Strong-Tie Strong-Drive screws are permitted to be installed through
metal truss plates as approved by the Truss Designer, provided the requirements
of ANSI/TPI 1-2007 Sections 7.5.3.4 and 8.9.2 are met (pre-drilling required
through the plate using a maximum of
5
⁄ 32 " bit).
5. SDS screws that penetrate all plies of the supporting girder (screws must penetrate a
minimum of 1" into the last truss ply) may also be used to transfer the load through all
the plies of the supporting girder. When SDS screws do not penetrate all plies of the
supporting girder truss, supplemental SDS screws at the hanger locations may be required
to transfer the load to the truss plies not penetrated by the face fasteners, as determined
by the Designer.
6. The supporting girder truss must have adequate thickness to accommodate the screw length,
so that the screw does not protrude out the back of the girder. 3" or 4
1
⁄ 2 " long SDS screws
may be substituted for the longer SDS screws with no load reduction.
7. For installations to LSL, use the DF/SP table loads.
HGUQ hangers provide similar capacities as HGUS double shear hangers, but they use Simpson
Strong-Tie
®
Strong-Drive
®
SDS screws instead of nails for faster and easier installation. In addition, the
SDS screws help transfer the load between the plies of the supporting girder when they penetrate all plies.
MATERIAL: 12 gauge FINISH: Galvanized
INSTALLATION:•Useallspecifiedfasteners.SeeGeneralNotes.
•SimpsonStrong-TieStrong-DriveSDSscrewssupplied.
•Notdesignedforweldedornailerapplications.
•Thethicknessofthesupportinggirdermustbeequaltoorgreaterthanthescrewlength.
For applications where the length of the supplied screws exceeds the thickness of the
supporting girder, 3" or 4
1
⁄ 2 " screws may be substituted for the longer length screws with
no load reduction, or a shim block may used as approved by the Designer.
OPTIONS: These hangers cannot be modified.
CODES: See page 13 for Code Reference Key Chart.
Model
No.
Min.
Heel
Height
Dimensions Fasteners DF/SP Allowable Loads SPF/HF Allowable Loads
Code
Ref.
W H B
Carrying
Member
Carried
Member
Uplift
(160)
Floor
(100)
Snow
(115)
Roof
(125)
Wind
(160)
Uplift
(160)
Floor
(100)
Snow
(115)
Roof
(125)
Wind
(160)
SINGLE 2x SIZES
HTU26
8
3
1
⁄ 2 1
5
⁄ 8 5
7
⁄ 16 3
1
⁄ 2 20-16d 11-10dx1
1
⁄ 2 670 2735 2735 2735 2735 575 1725 1725 1725 1725
I7,
L17,
F22
HTU26 (Min) 3
7
⁄ 8 1
5
⁄ 8 5
7
⁄ 16 3
1
⁄ 2 20-16d 14-10dx1
1
⁄ 2 1175 2940 3100 3100 3100 1010 1955 1955 1955 1955
HTU26 (Max) 5
1
⁄ 2 1
5
⁄ 8 5
7
⁄ 16 3
1
⁄ 2 20-16d 20-10dx1
1
⁄ 2 1215 2940 3340 3600 3760 1045 2370 2370 2370 2370
HTU28 (Min) 3
7
⁄ 8 1
5
⁄ 8 7
1
⁄ 16 3
1
⁄ 2 26-16d 14-10dx1
1
⁄ 2 1125 3770 3770 3770 3770 970 2825 2825 2825 2825
HTU28 (Max) 7
1
⁄ 4 1
5
⁄ 8 7
1
⁄ 16 3
1
⁄ 2 26-16d 26-10dx1
1
⁄ 2 1920 3820 4340 4680 5015 1695 3285 3730 3765 3765
HTU210 (Min) 3
7
⁄ 8 1
5
⁄ 8 9
1
⁄ 16 3
1
⁄ 2 32-16d 14-10dx1
1
⁄ 2 1250 3600 3600 3600 3600 1075 2700 2700 2700 2700
HTU210 (Max) 9
1
⁄ 4 1
5
⁄ 8 9
1
⁄ 16 3
1
⁄ 2 32-16d 32-10dx1
1
⁄ 2 3255 4705 5020 5020 5020 2800 3765 3765 3765 3765
DOUBLE 2x SIZES
HTU26-2 (Min) 3
7
⁄ 8 3
5
⁄ 16 5
7
⁄ 16 3
1
⁄ 2 20-16d 14-10d 1515 2940 3340 3500 3500 1305 2205 2205 2205 2205
I7,
L17,
F22
HTU26-2 (Max) 5
1
⁄ 2 3
5
⁄ 16 5
7
⁄ 16 3
1
⁄ 2 20-16d 20-10d 1910 2940 3340 3500 3500 1645 2205 2205 2205 2205
HTU28-2 (Min) 3
7
⁄ 8 3
5
⁄ 16 7
1
⁄ 16 3
1
⁄ 2 26-16d 14-10d 1490 3820 3980 3980 3980 1280 2985 2985 2985 2985
HTU28-2 (Max) 7
1
⁄ 4 3
5
⁄ 16 7
1
⁄ 16 3
1
⁄ 2 26-16d 26-10d 3035 3820 4340 4680 5555 2610 3285 3730 4025 4165
HTU210-2 (Min) 3
7
⁄ 8 3
5
⁄ 16 9
1
⁄ 16 3
1
⁄ 2 32-16d 14-10d 1755 4255 4255 4255 4255 1510 3190 3190 3190 3190
HTU210-2 (Max) 9
1
⁄ 4 3
5
⁄ 16 9
1
⁄ 16 3
1
⁄ 2 32-16d 32-10d 3855 4705 5345 5760 6470 3315 4045 4595 4855 4855
Model
No.
Ga
Dimensions SDS Fasteners DF/SP Allowable Loads SPF/HF Allowable Loads
Code
Ref.
W H B
Carrying
Member
Carried
Member
Uplift
1
(160)
Floor
(100)
Snow
(115)
Roof
(125)
Wind
(160)
Uplift
1
(160)
Floor
(100)
Snow
(115)
Roof
(125)
Wind
(160)
DOUBLE 2x SIZES
HGUQ26-2-SDS3 12 3
5
⁄ 16 5
7
⁄ 16 4 (12)
1
⁄ 4 "x3" (4)
1
⁄ 4 "x3" 1635 5040 5565 5565 5565 1175 3630 4005 4005 4005
F22HGUQ28-2-SDS3 12 3
5
⁄ 16 7
3
⁄ 16 4 (20)
1
⁄ 4 "x3" (6)
1
⁄ 4 "x3" 2565 7330 7330 7330 7330 1845 5280 5280 5280 5280
HGUQ210-2-SDS3 12 3
5
⁄ 16 9
3
⁄ 16 4 (28)
1
⁄ 4 "x3" (8)
1
⁄ 4 "x3" 3440 7415 7415 7415 7415 2475 5340 5340 5340 5340
TRIPLE 2x SIZES
HGUQ26-3-SDS4.5 12 4
15
⁄ 16 5
1
⁄ 2 4 (12)
1
⁄ 4 "x4
1
⁄ 2 " (4)
1
⁄ 4 "x4
1
⁄ 2 " 1635 5040 5165 5165 5165 1175 3630 3720 3720 3720
F22HGUQ28-3-SDS4.5 12 4
15
⁄ 16 7
1
⁄ 4 4 (20)
1
⁄ 4 "x4
1
⁄ 2 " (6)
1
⁄ 4 "x4
1
⁄ 2 " 2565 8400 9175 9175 9175 1845 6050 6605 6605 6605
HGUQ210-3-SDS4.5 12 4
15
⁄ 16 9
1
⁄ 4 4 (28)
1
⁄ 4 "x4
1
⁄ 2 " (8)
1
⁄ 4 "x4
1
⁄ 2 " 3440 9745 9745 9745 9745 2475 7015 7015 7015 7015
QUADRUPLE 2x SIZES
HGUQ26-4-SDS6 12 6
9
⁄ 16 5
7
⁄ 16 4 (12)
1
⁄ 4 "x6" (4)
1
⁄ 4 "x6" 2375 5040 5165 5165 5165 1710 3630 3720 3720 3720
F22HGUQ28-4-SDS6 12 6
9
⁄ 16 7
3
⁄ 16 4 (20)
1
⁄ 4 "x6" (6)
1
⁄ 4 "x6" 4020 8400 8860 8860 8860 2890 6050 6380 6380 6380
HGUQ210-4-SDS6 12 6
9
⁄ 16 9
3
⁄ 16 4 (28)
1
⁄ 4 "x6" (8)
1
⁄ 4 "x6" 4170 10260 10260 10260 10260 3000 7385 7385 7385 7385
4x SIZES
HGUQ46-SDS3 12 3
5
⁄ 8 4
7
⁄ 8 4 (12)
1
⁄ 4 "x3" (4)
1
⁄ 4 "x3" 1635 5040 5165 5165 5165 1175 3630 3720 3720 3720
F22HGUQ48-SDS3 12 3
5
⁄ 8 6
7
⁄ 8 4 (20)
1
⁄ 4 "x3" (6)
1
⁄ 4 "x3" 2565 7330 7330 7330 7330 1845 5280 5280 5280 5280
HGUQ410-SDS3 12 3
5
⁄ 8 8
7
⁄ 8 4 (28)
1
⁄ 4 "x3" (8)
1
⁄ 4 "x3" 3440 7415 7415 7415 7415 2475 5340 5340 5340 5340