Pocket Programmer UPB Pocket Programmer User Guide Model UPP
Pocket Programmer DESCRIPTION The Pocket Programmer (model UPP) provides many of the features of UPStart UPB configuration software in a portable hand held device. The Pocket Programmer comes with a handy carrying case and AC power cord that plugs into any standard receptacle allowing communication to installed UPB devices. The Pocket Programmer is intended for use by an installer who is familiar with UPStart and UPB products.
Pocket Programmer Model UPP INSTALLATION The Pocket Programmer is designed for indoor use. Simply plug the appropriate end of the provided AC cord into the top of the UPP, the other end into any 120-volt outlet anywhere in the house. Once the Pocket Programmer completes its start up procedure the top two (of six) selections of the main menu are on the display and it is ready for use.
Pocket Programmer FUNCTION: Toggles the backlight on the LCD display. LED: The diagnostic LED operates just as the LED on the Computer Interface Module. In Run CIM mode the Pocket Programmer exchanges UPB messages between the powerline and the connected computer or controller. The indicator on the UPP will glow AMBER when powered, flash RED when UPB messages are seen on the power line and flash GREEN when a UPB message is transmitted from the Pocket Programmer.
Pocket Programmer Model UPP Access Network is used on an installed UPB network. It is useful when viewing or editing devices. Devices can be added or deleted. Links may also be added or deleted. The same functions are available in UPStart under the Device, Link and Network menus.
Pocket Programmer New Network Model UPP 1)Access Network 1 2)New Network
Pocket Programmer Model UPP Add Device is used to add installed UPB devices to the UPB network. If a device is not found: 1. Make sure there is only one device in set up mode. 2. Check the wiring to ensure the connections are proper and the wire nuts are on tight. 3. Check the phase coupler to ensure it is properly installed and operational.
Pocket Programmer Model UPP Edit Device is used to change the settings on a previously added device. For instance, the dimming can be disabled under the Options sub-menu.
Pocket Programmer Model UPP 9
Pocket Programmer Model UPP 10
Pocket Programmer Model UPP Edit Device Sub-Menu – Transmit Links 1)ID 1 2)Receive Links 1)ID 2 2)Receive Links 2)Receive Links 3)Transmit Links 3 01)Link=241
Pocket Programmer Model UPP 12
Pocket Programmer Model UPP 1)ID 1 2)Receive Links Edit Device - Advanced 1)ID 2 2)Receive Links 2)Receive Links 3 3)Transmit Links 1)Xmit Type: 1 2)Xmit Atmpts: Transmit Type= 1)Xmit Type: 2 2)Xmit Atmpts: 2)Xmit Atmpts: 3 3)Xmit 2 Rpeatr: Link Transmit Type= Direct
Pocket Programmer 1)Add Device 1 2)Edit Device Model UPP View Device View is Read Only
Pocket Programmer Model UPP Add Link 1)Access Network 1 2)New Network Add Link is used to create and add a Link to one or more UPB devices.
Pocket Programmer Model UPP .
Pocket Programmer Model UPP UPB Explorer – Smart Transmit 1 1)Access Network 2)New Network 1 1)Smart Transmit 2)Smart Receive 1)Access Network 2)New Network 2 1)Smart Transmit 2)Smart Receive 2 2)New Network 3 3)UPB Explorer
Pocket Programmer Model UPP . Smart Receive is used to observe UPB transmissions.
Pocket Programmer Model UPP .
Pocket Programmer Model UPP Simply Automated, Incorporated 5825 Avenida Encinas, Suite 101, Carlsbad, CA 92008 USA Technical Support: www.simply-automated.com or 800-630-9234 452-0031-0001 Rev.
