Owner’s Manual Installation and Operation Model(s): SF-WM36-WH SF-WM36-BK NOTICE DO NOT DISCARD THIS MANUAL • Important operating and maintenance instructions included. • Read, understand and follow these instructions for safe installation and operation. • Leave this manual with party responsible for use and operation. D DI O N SC OT AR D READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE, OR MAINTAIN THIS PRODUCT. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION.
1 Important Instructions important safety instructions WARNING! Risk of Fire! Risk of Burns! Risk of Electrical Shock! DO NOT: • • • Install or operate damaged heater Modify heater Operate the heater without fully assembling all components The following actions are strictly prohibited. • Installation other than as instructed by Hearth & Home Technologies Inc. • Installation and/or use of any component part not approved by Hearth & Home Technologies Inc. Hearth & Home Technologies Inc.
Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. B. Congratulations Congratulations on selecting a SimpliFire Electric Fireplace, an elegant and clean alternative to wood & gas burning fireplaces. The SimpliFire electric fireplace you have selected is designed to provide the utmost in safety, reliability, and efficiency.
Safety Alert Key: • WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury. • CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Table of Contents 1 Important Instructions A. Important Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 B. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 C. Limited Lifetime Warranty. . . . . . . . . . . . . . .
C. Limited Lifetime Warranty Hearth & Home Technologies LIMITED LIFETIME WARRANTY Hearth & Home Technologies, on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
B. Limited Lifetime Warranty (continued) This warranty is void if: • • • The appliance is operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals. The appliance is subjected to prolonged periods of dampness or condensation. There is any damage to the appliance or other components due to water or weather damage.
2 General Information A. Appliance Certification MODELS: SF-WM36 LABORATORY: CSA International TYPE: Electric Air-Heaters Fixed and Location-Dedicated Electric Room Heaters STANDARD: UL 2021 (2nd Edition) CSA C22.2 No 46-M1988 NOTICE: This installation must conform with local codes. NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE. This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.
3 Getting Started A. Parts and Hardware Parts and Hardware List Part Quantity Fireplace 1 Instruction Manual 1 Remote Control 1 CR2032 Battery 1 Wall Mounting Bracket 1 Masonry Anchor 4 Screw ST5 x 40 4 Bolt M4 x 8 2 Bolt M5 x 10 2 White Stones 1 Clear Resin Faux Stones 1 3/16 Toggle Bolt Anchors 4 Masonry Anchor Screw 5 x 40 Bolt 4x8 Bolt 5 x 10 B.
D. Location F. Electrical Supply Circuit Requirements • For best results, install out of direct sunlight. • Power supply service must be installed within proximity of electric fireplace prior to finishing to avoid reconstruction. Plan the location of the appliance so that it will have adequate electric power. A 15 AMP, 120V/60hz. circuit is required. Additional appliances on the same circuit as this heater may exceed the current rating of that circuit.
4 Installation WARNING! Risk of Damage or Personal Injury! Failure to install the fireplace as instructed below may result in damage to the equipment and or may expose the user to the risk of fire, serious injury, illness or death. A. Wall Mounting Bracket The wall mounting bracket must be used to mount the appliance. This appliance must be mounted to a structural wall capable of bearing an 40 pound load. Determine the desired location of the appliance on the wall.
Framed Wall For each of the marked anchor point locations, determine if there is a structural framing member. If a wood or metal framing member exists, the 5 x 40 screw can be installed directly into that structural member. See Figure 4.3. In every mounting hole that does not align with a structural framing member, a wall board toggle-bolt anchor must be used. Figure 4.6 Installing Anchors in Hollow Wall C. Appliance Installation Figure 4.
D. Faux Stone Installation F. Electrical Connection Arrange the white and clear faux stones along the inset window ledge at the front of the firebox. Place clear resin pebbles over LEDs and fill remaining gaps with white stones. WARNING! Risk of Fire, Electrical Shock and Injury. Electrical wiring must comply with local building codes and other applicable regulations. E. Glass Front Installation 1. Install glass front as shown in Figure 4.5.
5 operating instructions CAUTION! The unit’s power cord must be connected to a properly grounded and protected 120V outlet. Always use ground fault protection where required by the electrical code. WARNING! Risk of Electric Shock! Do not operate the unit if it is damaged or has malfunctioned. If you suspect the unit is damaged, call a qualified service technician to inspect and replace any part of the electrical system if necessary. A.
B. Operating by Remote Control C. Resetting Temperature Cutoff Switch • The fireplace Main Power Switch must be in the “ON”position for the remote control to function. • Make sure batteries are properly installed in Remote Control. - Battery requirements CR2032 battery (included). The heater is protected with a safety device to prevent overheating. Should the heater overheat, an automatic cutoff will turn the heater OFF. It will not turn ON automatically without being reset.
6 maintenance A. Maintenance B. Cleaning WARNING! Risk of Shock! Always unplug the cord before moving or servicing. Do not immerse heater in water. Cleaning Glass • Always turn OFF the heater and disconnect the cord from the electrical outlet before cleaning your heater. • Light accumulated dust may be removed from the appliance exterior with a soft cloth or vacuum cleaner. • Wipe the exterior surfaces of the heater occasionally with a microfiber cloth using a solution of mild detergent and water.
C. Service Parts List Service Parts SF-WM36-WH, SF-WM36-BK Beginning Manufacturing Date: Feb 2013 Ending Manufacturing Date: Active 36” Electric Fireplace #1 Black Glass #2 White Glass POWER FLAME BACKLIGHT LOW HIGH #4 Power cord #5 Hanging Bracket #3 Remote IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.
D. Replacement Instructions WARNING! Risk of Shock! Always unplug the cord before moving or servicing. Power Input Cord Replacement 1. Switch the main switch control on the lower right corner of the appliance to the OFF position. 2. Unplug the power input cord from the wall receptacle. 3. Locate power input cord connection located on the lower right corner of the appliance. 4. Remove one screw and metal strain relief bracket. See Figure 6.1. 5. Unplug cord from appliance. 6.
E. Contact Information SimpliFire, a brand of Hearth & Home Technologies 7571 215th Street West, Lakeville, MN 55044 www.hearthnhome.com Please contact your SimpliFire dealer with any questions or concerns. For the location of your nearest SimpliFire dealer, please visit www.hearthnhome.com.
