AGCO LAWN & GARDEN EQUIPMENT OPERATOR'S MANUAL Prestige / 1 800 / 2800 Conquest/1700 20HP Mfg. No. 1694625 1694679 1694752 1694746 1694747 2690265 2690268 2690270 2690262 2690266 2690265 21HP Mfg. No. 1694904 1694905 1694906 1694907 2690454 2690455 2690456 22HP Mfg. No.
Tableof Contents Safety Rules & Information ................................. Identification Numbers ........................................ Safety Decals ....................................................... Safety Icons ......................................................... Features & Controls .......................................... Control Functions .................................................. Parking Brake Function ......................................... Automatic Controlled Traction ..
SafetyRules& Information OperatingSafety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety. Power equipment is only as safe as the operator. If it is misused, or not properly maintained, it can be dangerous! Remember, you are responsible for your safety and that of those around you. Use common sense, and think through what you are doing.
SafetyRulesandinformation SlopeOperation You could be seriously injured or even killed if you use this unit on too steep an incline. Using the unit on a slope that is too steep or where you don't have adequate traction can cause you to lose control or roll over. 3.5 20 A good rule of thumb is to not operate on any slope you cannot back up (in 2-wheel drive mode). You should not operate on inclines with a slope greater than a 3.5 foot rise over a 20 foot length.
SafetyRules& Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing deck is capable of amputating hands and feet and throwing objects. The triangle _, in text signifies important cautions or warnings which must be followed. GENERAL OPERATION 1.
SafetyRulesandInformation SLOPE OPERATION WARNING Slopes are a major factor related to loss-of-control and tipover accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not operate on it. Control of a walk-behind or ride-on machine sliding on a slope will not be regained by the application of the brake.
SafetyRules& information SERVICE AND MAINTENANCE Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition. 2. Use only approved gasoline containers. 3. Never remove the gas cap or add fuel with the engine running. Allow the engine to cool before refueling. 4. Never fuel the machine indoors. 5. Never store the machine or fuel container where there is an open flame, spark, or pilot light such as near a water heater or other appliance. 6.
Identification Numbers '----_Ncp_piicity Manufacturing '_._ _WI inc. 53074-0997 USA North American CE Models / flllllllllilllll_llllllllllll SERIAL N0. X_X_300(XX Mfg. ]___?:_'I CE Models ikw: _/x iEXx,: oooPM _>) Simplicity LPort Mfg. Inc. Washington, W xx_X_ (Only) _ /_\ Mower ID Tag Tracto \ USA 53_7_ Model Description Name/Number When contacting your authorized dealer for replacement parts, service, or information you MUST have these numbers.
SafetyDecals Safety Decals This unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing. Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this equipment safely and effectively, we have placed several safety labels on the unit to remind you of this important information while you are operating your unit.
CESafetyicons Safety Icons Danger: Machine Rollover. Warning: Read Operator's Manual. Do not use this machine on slopes greater than 10 °. Read and understand the Operator's Manual before using this machine. Danger: Thrown Objects. Danger: Dismemberment. This machine is capable of throwing objects and debris. Keep bystanders away. This machine can amputate limbs. Keep bystanders and children away when engine is running. Warning: Remove Key Before Servicing. Danger: Dismemberment.
Features& Controls Electric HOC Models Hydraulic Lift Models Manual Lift Models Manual HOC Models Figure 1. Controls Control Functions The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section.
Features& Controls, _PTO Manual Lift Models: The cutting height adjustment knob controls the mower cutting height. Switch The PTO (Power Take-Off) switch engages and disengages attachments that use the PTO. To engage the PTO, pull UP on the switch. Push DOWN to disengage. Note that the operator must be seated firmly in the tractor seat for the PTO to function. _'_ H D Cruise Control (Select Models) The cruise control is used to lock the ground speed control in forward.
Features& Controls _ Attachment Lift Control Manual Lift Models: The attachment lift control lever raises and lowers attachments that utilize the tractor's manual lift linkage. To lower an attachment: pull the lever back slightly, depress the release button, and push the lever forward until it locks in the lowered position. To raise an attachment: push the lever forward slightly, depress the release button, then pull the lever back until it locks in the raised position.
Features& Controls Dashboard Display Display & Functions Items Refer to Figures 3. A. FUEL LEVEL Indicates the amount of fuel in the fuel tank. Left is empty; right is full. B. HOUR METER / CLOCK / SERVICE INDICATOR Displays the clock, hour meter, and maintenance reminder. C. SELECT BUTTON Figure 3. Dashboard Display - Select Models Used to set the clock and reset the maintenance reminder. Functions D. SET BUTTON DASHBOARD Used to set the clock and reset the maintenance reminder. E.
Operatingthe Tractor General Operating Safety Interlock System Tests Be sure to read all information in the Safety and Operation sections before attempting to operate this unit. Become familiar with all of the controls and how to stop the unit. This unit is equipped with safety interlock switches and other safety devices. These safety systems are present for your safety: do not attempt to bypass safety switches, and never tamper with safety devices. Check their operation regularly.
Operating theTractor Starting the Engine Stopping 1. While sitting in the operator's seat, fully depress the brake pedal or set the parking brake. the Tractor & Engine 1. Return the ground speed control(s) to neutral. 2. Disengage the PTO and wait for all moving parts to stop. 2. Make sure that your feet are not depressing the ground speed control pedals and that the cruise control lever is in neutral. Kohler Models 3. Set the throttle to Full. 3. Disengage the PTO clutch. Briggs & Stratton 4.
Operating theTractor Attachment Operation in Reverse Mowing 1. Set the mower cutting height to the desired level and set the gauge wheels to the appropriate position (if equipped). If an operator chooses to operate a PTO driven attachment in reverse, the RMO system can be used. To use the Reverse Mowing Option (RMO) turn the RMO key after the PTO is engaged. The L.E.D. light will illuminate, and the operator can then operate the attachment in reverse.
Operating theTractor Pushing the Tractor by Hand 1. Disengage the PTO and turn the engine off. 2. Pull the transmission release (B, Figure 4) back approximately 2-1/2" (6 cm) to lock into released position. 3. The tractor can now be pushed by hand. ® DO NOT TOW TRACTOR Towing the unit will cause transmission damage. • Do not use another vehicle to push or pull this unit. • Do not actuate the transmission release valve lever while the engine is running. Figure 4. Transmission Release Lever & Fuel Tank A.
Operating theTractor Mower Deck Removal & Installation 44" Simplicity, Massey Ferguson or AGCO Models % Engage parking brake, disengage PTO, stop engine and remove key before attempting to install or remove the mower. Removing Figure 6. Lift Arms (Viewed from underneath right side of tractor) A. Mower Lift Arm C. Flat Washer B. Tractor Lift Arm D. Safety Clip the Mower Deck Note: Units with electric height of cut, unplug tractor wire harness from deck harness before removing deck. 1.
Operating theTractor Mower Deck Removal & Installation 44" Snapper Models WARNING Engage parking brake, disengage PTO, stop engine and remove key before attempting to install or remove the mower. Removing Figure 9. Lift Arms (Viewed from underneath left side of tractor) A. Safety Clip E. Lower Hanger B. Upper Hanger F. Post on Lift Hook C. Lift Hook G. Washer D. Lift Chain H.
Operating theTractor Mower Deck Removal & Installation Simplicity, Models Massey Ferguson and AGCO Figure 11. Pivoting Gauge Wheels - Select Models WARNING Engage parking brake, disengage PTO, stop engine and remove key before attempting to install or remove the mower. Muffler and surrounding areas may be hot. Removing Figure 12. Mower Lift A. Lift Hook B. Lift Chain the Mower Deck Note: Units with electric height of cut, unplug tractor wire harness from deck harness before removing deck. 1.
Operating theTractor Installing the Mower Deck NOTE: Perform mower installation on a hard, level surface such as a concrete floor. 1. Park the tractor, fully lower the attachment lift, turn off the PTO switch, turn off the engine, remove the key, and engage the parking brake. Turn the wheels fully to the left. t 2. Place mower in the lowest cutting position using the mower height adjuster.
Operating theTractor Mower Deck Removal & Installation 50" & 54" Snapper Models WARNING Figure 14. Mower Lift A. Lift Hook B. Lift Chain, Inside C. Hanger Engage parking brake, disengage PTO, stop engine and remove key before attempting to install or remove the mower. D. Outside Chain E. PTO Belt F. Idler Arm Muffler and surrounding areas may be hot. Removing the Mower Deck 1.
Operating theTractor Attaching a Trailer The maximum horizontal drawbar force allowed is 444 Newton. The maximum vertical drawbar force is 222 Newton. This equates to a 396 Ibs (180 kg) trailer on a 10 degree hill. Secure the trailer with an appropriately sized clevis pin (A, Figure 16) and clip (B). J I WARNING ® Never store the unit (with fuel) in an enclosed, poorly ventilated structure. Fuel vapors can travel to an ignition source (such as a furnace, water heater, etc.) and cause an explosion.
Operating theTractor @ • _.._. :-'\_ _ y ._ _-_- Snowthrower & Dozer Applications S nowt hrowe r & Dozer Applications .- f Mower Applications ! x x )t i _ ] Figure 17. Lift Lock Plate - Hydraulic Lift Models A. Lift Cylinder B. Flat Head Pin (Original) C. Flat Head Pin (New) D. Lock Plate E. Hair Pin Clips F. Lift Shaft Assy. G. Washers Figure 18. Lift Link - Manual Lift Models A. Pin B. Rear Hole of Lift Bar (Snowthrower Applications) C. Spacer D. Hair Pin Clip E.
LawnCare & MowingInformation HOW TO WATER YOUR LAWN How and When to Water, Fertilize & Aerate The best method of watering a lawn is to imitate a slow, soaking rain, applying about 1 inch of water. HOW TO FERTILIZE YOUR LAWN Most lawns are watered too often, but with too little water. However too much water can allow development of diseases with your lawn. It is best to water the lawn only when necessary, and then to water it slowly, evenly, and deeplymimitating a slow, soaking rain.
LawnCare& MowingInformation When and How Often to Mow The time of day and condition of the grass greatly affect the results you'll get when mowing. For the best results, follow these guidelines: • Mow when the grass is between 3"-4" (7,5-10 cm) high. • Mow with sharp blades. Short clippings of grass one inch or shorter decompose more quickly than longer blades. Sharp mower blades cut grass cleanly and efficiently, preventing frayed edges which harm the grass.
Regular Maintenance MAINTENANCE SCHEDULE & PROCEDURES The following schedule should be followed for normal care of your tractor and mower.
RegularMaintenance Check/Clean Oil Cooler (Select Models) SERVICE INTERVAL: NECESSARY EVERY 25 HOURS, OR AS The engine oil cooler is located on the side of the engine (A, Figure 19) and should be cleaned with compressed air at regular intervals or if dirty. Safety Interlock System Check SERVICE INTERVAL: EVERY FALL & SPRING Check the function of the safety interlock system using the test procedure found on page 14 of this manual. If the tractor fails any of the tests, see your dealer. Figure 19.
RegularMaintenance Check Tire Pressures SERVICE INTERVAL: EVERY 25 HOURS Tire Pressure should be checked periodically, and maintained at the levels shown in the chart. Note that these pressures may differ slightly from the "Max Inflation" stamped on the side-wall of the tires. The pressures shown provide proper traction, improve cut quality, and extend tire life. Size PSI bar 24 x 12-12 6-8 ,41-,55 23x 10.5-12 6-8 ,41-,55 16 x 6.50-8 15 1,0 Figure 20.
RegularMaintenance Lubrication SERVICE INTERVAL: EVERY 25 HOURS Lubricate the unit at the locations shown in Figures 2225 as well as the lubrication points listed. Generally, all moving metal parts should be oiled where contact is made with other parts. Keep oil and grease off belts and pulleys. Wipe surfaces clean before and after lubrication.
RegularMaintenance Lubricate Rear Axle Shafts Prestige / 2800 / 1800 / 500 / GT SERVICE INTERVAL: YEARLY We recommend removing the rear wheel hubs and lubricating the axle shafts yearly. This prevents the wheel hubs from seizing onto the axle shaft and makes future service easier. 1. Turn off the ignition, turn off the PTO, engage the parking brake, and block the front tires. 2.
RegularMaintenance WARNING For your personal safety, do not handle the sharp mower blades with bare hands. Careless or improper handling of blades may result in serious injury. WARNING For your personal safety, blade mounting capscrews must each be installed with a hex/spline washer and spring washer, then securely tightened. Torque blade mounting capscrew to 45 - 55 ft. Ibs. (61 - 75 N.m.) LOOSEN Figure 27.
RegularMaintenance Transmission Identification Several service procedures within this book are identified by, and vary by, transmission type. To determine what transmission is in your tractor, check the identification tag attached to the axle of the transmission (Figure 31a), or check your tractor's parts book. Transmission ® Figure 30. Blade Installation - 54" Mowers A. 4x4 Wood Block B. Spline Washer C. Spring Washer D.
RegularMaintenance Figure 32. Seat Deck Access Plug A. Expansion Chamber Access Plug Figure 33. Differential Fill Plug Access A. Differential Fill Plug K71 Maintenance The following maintenance procedures must be performed on the K71 transmission after the first 50 hours of operation and then after every 250 hours. TRANSMISSION INFORMATION Transmission Oil Capacity: Apx. 4-1/2 qt (4.25L) Transmission Oil Type: SAE 10W-30 with a minimum API rating of SG/CD.
RegularMaintenance 0 0 Figure 36. Internal Transmission Filter Service A. Filter Access Cap B. Internal Filter Figure 37. Transmission A. 14mm Drain Plugs B. Filter Access Cap 5. Remove and replace the internal transmission filter (B, Figure 36). 6. Reinstall the filter access cap (A, Figure 36) and the two 14mm drain plugs (A, Figure 37). 7. Using a long funnel, add 2 quarts of oil to the differential fill (See Figure 33). The differential fill cap should have been removed earlier). 8.
Troubleshooting, Adjustment, & Service Troubleshooting WARNING While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. To avoid serious injury, perform maintenance on the tractor or mower only when the engine is stopped and the parking brake engaged.
Troubleshooting, Adjustment, & Service Tractor Troubleshooting Tractor Cont. drive belt slips. Brake will not hold. Tractor steers hard or handles poorly. 1. 2. 3. 4. 1. 2. 1. 2. 3. TROUBLESHOOTING PROBLEM Mower will not raise. Clutch/brake is out of adjustment. Pulleys or belt greasy or oily. Belt stretched or worn. Idler pulley pivot bracket "frozen" in declutched position. Brake is incorrectly adjusted. Internal brake worn. See Adjustments Section. Clean as required. Replace with new belt.
Troubleshooting, Adjustment, & Service Battery Charging WARNING Keep open flames and sparks away from the battery; the gasses coming from it are highly explosive. Ventilate the battery well during charging. A dead battery or one too weak to start the engine may be the result of a defect in the charging system or other electrical component. If there is any doubt about the cause of the problem, see your dealer.
Troubleshooting, Adjustment, & Service Steering Wheel Adjustment NOTE: The steering wheel on Snapper models is not adjustable. 1. Use a suitable punch to remove the roll pin at the base of the steering wheel (B, Figure 41). 2. Pull down on the rubber boot to expose the two holes in the steering shaft (A). Thicker Spoke Faces Seat 3. Align the hole in the steering wheel with the appropriate steering shaft hole and install the roll pin.
Troubleshooting, Adjustment, & Service PTO clutch adjustment WARNING To avoid serious injury, perform adjustments only with engine stopped, key removed and tractor on level ground. Check the PTO clutch adjustment after every 250 hours of operation. Also perform the following procedure if the clutch is slipping or will not engage, or if a new clutch has been installed. 1.
Troubleshooting, Adjustment, & Service Gauge Wheels (Select Models) The mower gauge wheels can be placed in several positions depending on the height of cut. When using higher cutting heights, set the wheels in the lower position. When using lower cutting heights, set the wheels in the upper position. To adjust: PIVOTING GAUGE WHEELS 1. Remove the hair pin clip (A, B, Figure 46). 2. For upper position, install the pin (A) through the spindle above the bracket (C).
Troubleshooting, Adjustment, & Service Leveling The Mower If the cut is uneven, the mower may need leveling. Unequal or improper tire pressure may also cause an uneven cut. Make sure tire pressure is correct as specified in Checking Tire Pressure. SIDE-TO-SIDE LEVELING 1. With the mower installed, place the tractor on a smooth, level surface such as a concrete floor. Turn the front wheels straight forward. 2. Check for bent blades and replace if necessary. 3. Place the mower in mid-cut position.
Troubleshooting, Adjustment, & Service Mower Belt Replacement Q BELTS OVER PULLEYS. o avoid damaging belts, DO NOT PRY 44" & 50" PTO Belt Replacement 1. Park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, turn off the engine and lock the parking brake. Remove the key. Remove the mower or place in the lowest cutting position. FRONT 2. Move the idler arm (A, Figure 53) to relieve belt tension. Drop the belt from the PTO (electric clutch) pulley. Figure 53.
Troubleshooting, Adjustment, & Service 1 Figure 55. Mower Deck - 44" & 50" Mowers A. Capscrew B. Right-hand Arbor Cover C. Spring D. Left-hand Arbor Cover Arbor Drive Belt Replacement 44", 50", & 54" Mowers Figure 56. Mower Deck- 54" Mowers A. Taptite Screws B. Right-hand Arbor Cover C. Spring D. Left-hand Arbor Cover E. Alignment Notches - NOTE: Be sure to use only genuine Simplicity replacement parts. FRONT 1. Park the tractor on a smooth, level surface such as a concrete floor.
Specifications NOTE: Specifications are correct at time of printing and are subject to change without notice. * The power ratings for an individual engine model are initially developed by starting with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure) (Revision 2002-05).
Parts& Accessories Replacement Parts Technical Replacement parts are available from your authorized dealer. Always use genuine Simplicity Service Parts. Additional copies of this manual are available, as well as fully illustrated parts lists. These manuals show all of the product's components in exploded views (3D illustrations which show the relationship of parts and how they go together) as well as part numbers and quantities used. Important assembly notes and and torque values are also included.
0 Bimplicilq MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 PRODUCTS, INC. 535 Macon Street McDonough, GA 30253 www.SimplicityMfg.com www.Snapper.com MASSEY FERGUSON AWN & GARDEN EQUIPMENT .,4GCO LAWN & GARDEN EQUIPMENT 500 N Spring Street / PO Box 997 Port Washington, Wl 53074-0997 500 N Spring Street / PO Box 997 Port Washington, Wl 53074-0997 www.MasseyLawn.com www.AGCOLawn.
