SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage. Keep manual for future reference.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS This product has been designed and constructed according to general engineering standardsa. Other local regulations may apply and must be followed by the operator. We strongly recommend that all personnel associated with this equipment be trained in the correct operational and safety procedures required for this product. Periodic reviews of this manual with all employees should be standard practice.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS TABLE OF CONTENTS 1. Introduction .......................................................................................................................... 5 2. Safety First............................................................................................................................ 7 2.1. General Safety ......................................................................................................... 8 2.2.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS TABLE OF CONTENTS 6. Maintenance & Storage...................................................................................................... 6.1. Maintenance ........................................................................................................... 6.1.1. Hydraulic Winch Valve.............................................................................. 6.1.2. Ram Speed Adjustment......................................
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 1. INTRODUCTION 1. Introduction Congratulations. As the new owner of a Wheatheart self-propelled auger, you will be working with equipment especially designed to complement and improve your farming operation. Before using this auger, we recommend that you read this manual to familiarize yourself with the various features of the machine, and the necessary precautions for efficient and safe operation.
1.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 2. SAFETY FIRST 2. Safety First The Safety Alert symbol to the left identifies important safety messages on the product and in the manual. When you see this symbol, be alert to the possibility of personal injury or death. Follow the instructions in the safety messages. Why is SAFETY important to you? Three big reasons: • Accidents disable and kill. • Accidents cost. • Accidents can be avoided.
2. SAFETY FIRST 2.1. GENERAL SAFETY WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 2.1. GENERAL SAFETY Important: The general safety section includes instructions that apply to all safety practices. Any instructions specific to a certain safety practice (e.g., assembly safety), can be found in the appropriate section. Always read the complete instructional sections and not just these safety summaries before doing anything with the equipment.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 2. SAFETY FIRST 2.2. ASSEMBLY SAFETY • Follow good shop practices: • keep service area clean and dry • be sure electrical outlets and tools are properly grounded • use adequate light for the job at hand • Think SAFETY! Work SAFELY! 2.2. ASSEMBLY SAFETY • Read the instructions and familiarize yourself with the subassemblies and hardware making up the equipment. • The components are large, heavy, and can be hard to handle.
2. SAFETY FIRST 2.3. OPERATION SAFETY WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS Figure 2.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 2. SAFETY FIRST 2.4. TRANSPORT & PLACEMENT SAFETY 2.4. TRANSPORT & PLACEMENT SAFETY • Before raising/lowering/moving the auger, make sure the area around the auger is clear of obstructions and/or unauthorized personnel. Never allow anyone to stand on or beneath auger while transporting or placing auger. • Wheels must be free to move when raising or lowering auger. • Do not stand between towing vehicle and grain auger when hitching.
2. SAFETY FIRST 2.5. STORAGE SAFETY WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 2.5. STORAGE SAFETY • Store in an area away from human activity. • Do not permit children to play on or around the stored machine. 2.6. MAINTENANCE SAFETY • Before applying pressure to a hydraulic system, make sure all components are tight and that hoses and couplings are in good condition. • Relieve pressure from hydraulic circuit before servicing or disconnecting from tractor.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 2. SAFETY FIRST 2.8. ENGINE SAFETY • Before moving a hydraulic cylinder, ensure that the attached component is safely secured. WARNING Hydraulic fluid can cause serious injury if it penetrates the skin. If it does, see a doctor immediately. • Relieve pressure before disconnecting hydraulic line. • Wear proper hand and eye protection and use wood or cardboard, not hands, when searching for leaks. 2.8.
2. SAFETY FIRST 2.10. SAFETY DECAL LOCATIONS WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 2.10.1. DECAL INSTALLATION 1. Decal area must be clean and dry, with a temperature above 10°C (50°F). 2. Decide on the exact position before you remove the backing paper. 3. Align the decal over the specified area and carefully press the small portion with the exposed sticky backing in place. 4.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3. ASSEMBLY 3.1. GEAR PUMP ASSEMBLY 3. Assembly Warning: Before continuing, please reread the safety information relevant to this section at the beginning of this manual. Failure to follow the safety instructions can result in serious injury, death, or property damage. CAUTION Ensure the auger is in the fully lowered position and on a level surface with the wheels chocked before proceeding with any assembly. 3.1.
3. ASSEMBLY 3.2. PUMP GUARD ASSEMBLY WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS Figure 3.1 Gear Pump Installation Guard 3.2. PUMP GUARD ASSEMBLY 1. Bolt the pump guard bracket to the over-center pump bracket (Figure 3.1). • Install the pump guard bracket at the pump end of the long, adjustable slot, through the middle of the over-center bracket.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3. ASSEMBLY 3.3. OIL RESERVOIR ASSEMBLY • Take care not to crush the oil reservoir when tightening hose clamps. • The reservoir must be mounted so that the oil level remains above the gear pump (use general purpose ISO 32 oil). • To reduce weight at the intake end, mount the tank as close as possible to the axle of the auger. Figure 3.
3. ASSEMBLY 3.4. GEAR DRIVE ASSEMBLY WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3.4. GEAR DRIVE ASSEMBLY CAUTION Before removing the tires from the auger, ensure the auger is in the fully lowered position. Position the auger on a flat level surface and block the axle to fully support the auger while removing the wheels. 1. Remove tires from auger. 2. Insert ring gear into rim (Figure 3.3). Use a hammer to be sure the ring gear seats evenly into the rim. 3.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3. ASSEMBLY 3.5. OVER-CENTER DRIVE ASSEMBLY—ROUND AXLES 3.5. OVER-CENTER DRIVE ASSEMBLY—ROUND AXLES 1. Ensure shims fit on round axle. On some augers, shims are welded to hub; this can be checked by lining up with the tire rim. Shims are normally sized and supplied by the factory for individual augers. 2. Weld fitted shims to each axle cap (Figure 3.4). 3. Bolt axle cap axle near wheels, but do not tighten bolts.
3. ASSEMBLY 3.6. OVER-CENTER DRIVE ASSEMBLY—SQUARE AXLES WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3.6. OVER-CENTER DRIVE ASSEMBLY—SQUARE AXLES 1. Once the wheel is bolted to the hub, the over-center drive assembly can be installed. 2. Position the axle cap of the over-center drive assembly squarely on the axle tube as shown in Figure 3.6. 3. With the pinion gear flush with the ring gear (Figure 3.6), weld the axle cap to the axle tube. Figure 3.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3. ASSEMBLY 3.7. OVER-CENTER DRIVE ASSEMBLY—WHEATHEART BH AUGERS 3.7. OVER-CENTER DRIVE ASSEMBLY—WHEATHEART BH AUGERS 1. Once the wheel is bolted to the hub, the over-center drive assembly can be installed. 2. Position the axle cap of the over-center drive assembly squarely on the axle tube as shown in Figure 3.6. 3. With the pinion gear flush with the ring gear (Figure 3.5), bolt the axle cap to the axle tube. Figure 3.
3. ASSEMBLY 3.8. PINION GEAR ADJUSTMENT WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3.8. PINION GEAR ADJUSTMENT For gear depth alignment, refer to Figure 3.9. NOTICE Failure to ensure proper gear meshing will result in gear damage. The pinion gear should mesh with the ring gear to provide maximum tooth contact (Figure 3.5).
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3. ASSEMBLY 3.9. UNDERCARRIAGE INSTALLATION 3.9. UNDERCARRIAGE INSTALLATION Important: Pre-Assembly: When assembling the frame pipes, ram extension, and cylinder under the auger, the components should form a straight line from the axle to the ram mount ring when the auger is fully lowered.
3. ASSEMBLY 3.9. UNDERCARRIAGE INSTALLATION WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS Figure 3.10 Control Ring Installation Figure 3.11 Self-Propelled Auger Frame Installation 13. One end of the crossbrace is attached to the V-frame clevis, the other is attached to the transport tube using clamp bands (Figure 3.11). 14. When attaching to the V-frame, be sure to mount one crossbrace to the top side of the V-frame clevis, and the other to the bottom.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3. ASSEMBLY 3.10. RAM EXTENSION INSTALLATION 3.10. RAM EXTENSION INSTALLATION The ram extension slides into the A-frame attached to the tabs on the V-frame. The ram extension length must be set at the proper distance from the ram mounting A-frame for proper operation of the transport kit (see Table 3.1 or 3.2, and Figure 3.12). Table 3.
3. ASSEMBLY 3.11. WINCH ASSEMBLY WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS Figure 3.12 Ram Extension Installation 3.11. WINCH ASSEMBLY Important: 1. Lower auger completely and remove the hand winch on the lower auger frame. 2. Place the winch on the frame as shown in Figure 3.13 using the measurements in Table 3.3. The hydraulic winch position should be adjusted until the drum is 1” away from the auger tube when in transport position. On Wheatheart models, use Table 3.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3. ASSEMBLY 3.12. CABLE INSTALLATION If the cable does not index properly, lower the auger fully until there is slack in the cable. Loosen the nuts on the u-bolts. Adjust the winch, retighten nuts, and retest. Figure 3.13 Winch Positioning Table 3.3 Winch Positioning, Wheatheart Models AUGER 8” x 51’ 8” x 36’ 10” x 36’ 10” x 46’ 10” x 41’ DIM 'A' 5-1/2" 3-3/4" 1/2" 5-7/8" 6-5/8" WARNING Falling auger hazard.
3. ASSEMBLY 3.13. HOSE KIT LAYOUT—NO BIN SWEEP WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3. Wrap cable 1-1/2 times around the cable attach rod and secure with two 1/4” cable clamps. Position cable clamps as shown (Figure 3.14). Tighten cable clamps securely. 4. Rotate drum until cable is taut. Ensure drum is rotating in direction shown in Figure 3.13 when raising auger. 5. Tie up winch motor hydraulic hose as needed to prevent damage to the hose. 6.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3. ASSEMBLY 3.13. HOSE KIT LAYOUT—NO BIN SWEEP Figure 3.15 Wheatheart Hydraulic Schematic, SP Transport Kit without Bin Sweep Option Table 3.
3. ASSEMBLY 3.13. HOSE KIT LAYOUT—NO BIN SWEEP WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS Table 3.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3. ASSEMBLY 3.13. HOSE KIT LAYOUT—NO BIN SWEEP Figure 3.17 Competitor Auger Hydraulic Schematic—SP Transport Kit w/out Bin Sweep Option Table 3.
3. ASSEMBLY 3.13. HOSE KIT LAYOUT—NO BIN SWEEP WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS Table 3.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3. ASSEMBLY 3.14. HOSE KIT LAYOUT WITH BIN SWEEP 3.14. HOSE KIT LAYOUT WITH BIN SWEEP Refer to Table 3.6, Figure 3.16 and 3.18. SP TRANSPORT KIT INCLUDES: • hoses (A, B, E, F1, F2, G1, G2, H1, H2, I1, I2, J1, J2), winch valve, winch hoses (H1, H2) BIN SWEEP OPTION INCLUDES: • hoses (D, C, L, K), relief valve Figure 3.
3. ASSEMBLY 3.14. HOSE KIT LAYOUT WITH BIN SWEEP WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS Table 3.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3. ASSEMBLY 3.14. HOSE KIT LAYOUT WITH BIN SWEEP Figure 3.19 Competitor Auger Hydraulic Schematic—SP Transport Kit w/ Bin Sweep Option Table 3.
3. ASSEMBLY 3.14. HOSE KIT LAYOUT WITH BIN SWEEP WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS Table 3.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3. ASSEMBLY 3.15. HOSE KIT ASSEMBLY 3.15. HOSE KIT ASSEMBLY Refer to Figures 3.15 - 3.20. Important: 1. Assemble hoses as illustrated. 2. Keep free of dirt while assembling. 3. Keep pressure and return sides aligned. 4. Tighten after being satisfied that the hoses are in the proper position. 5. Check operation. 6.
3. ASSEMBLY 3.16. CUSHION VALVE INSTALLATION WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3.16. CUSHION VALVE INSTALLATION Connect the hoses as shown in Figure 3.21 and 3.22, ensuring that the hoses are not crossed. Connect the lower cushion block hoses to the lower ports on each hydraulic motor as shown. NOTICE Do not over-tighten fittings! Over-tightening hose fittings can crack the fittings or motor body and will void the warranty. Figure 3.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 3. ASSEMBLY 3.17. HYDRAULIC FILTER INSTALLATION 3.17. HYDRAULIC FILTER INSTALLATION WHEATHEART MODELS ONLY When connecting the hydraulic filter, make sure that it is properly installed. An arrow is engraved in the filter head indicating the direction of oil flow. The filter MUST be installed with the oil flowing in the same direction as the arrow indicates. The filter goes in the return line right before the tank. Figure 3.
3. ASSEMBLY 3.17.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 4. TRANSPORT & PLACEMENT 4.1. TRANSPORT PROCEDURE 4. Transport & Placement Warning: Before continuing, please reread the safety information relevant to this section at the beginning of this manual. Failure to follow the safety instructions can result in serious injury, death, or property damage. 4.1. TRANSPORT PROCEDURE Note: Use only a tractor or towing vehicle of adequate power and capacity to transport the machine.
4. TRANSPORT & PLACEMENT 4.2. PLACEMENT PROCEDURE WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 4.2. PLACEMENT PROCEDURE Follow this procedure when placing the machine into its working position: 1. Be sure there is enough clearance from overhead obstructions, power lines, or other equipment to move the machine into its working position. 2. Position machine in the desired area. For operating instructions, see Section 5.2. WHEN PLACING UNDER HOPPER BOTTOM BINS: 1.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 5. OPERATION 5.1. START-UP 5. Operation Warning: Before continuing, please reread the safety information relevant to this section at the beginning of this manual. Failure to follow the safety instructions can result in serious injury, death, or property damage. Operators must observe safety procedures at all times and follow the pre-operational checklist before each start-up.
5. OPERATION 5.2. OPERATING PROCEDURE WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS AFTER OPERATING OR TRANSPORTING FOR 1/2 HOUR: • Retorque all wheel bolts (if applicable). • Retorque all fasteners and hardware. • Check all safety decals are installed and legible. Apply new ones if needed. • Check all guards are installed and working as intended. AFTER 3 HOURS: • Change oil for best results. AFTER 5 AND 10 HOURS: • Check all hydraulic hoses and fittings for leaks.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 5. OPERATION 5.2. OPERATING PROCEDURE Figure 5.1 Hydraulic Control Valve Decal Figure 5.
5. OPERATION 5.2.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 6. MAINTENANCE & STORAGE 6.1. MAINTENANCE 6. Maintenance & Storage Warning: Before continuing, please reread the safety information relevant to this section at the beginning of this manual. Failure to follow the safety instructions can result in serious injury, death, or property damage. 6.1. MAINTENANCE Before performing any maintenance on this unit, shut off and remove key or lock out power source. 1.
6. MAINTENANCE & STORAGE 6.1. MAINTENANCE WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS WARNING Winch cable must be wound onto the drum of the winch from the top of the drum. This ensures the safe and proper operation of the hydraulic winch. 6.1.2. RAM SPEED ADJUSTMENT Ram speed is regulated at the control valve. The adjustable stroke limiter screws and lock nuts set the speed of ram travel individually in each direction (Figure 6.2).
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 6. MAINTENANCE & STORAGE 6.2. STORAGE 3. To increase hydraulic pressure: repeat step 2. except turn adjustment screw in (clockwise) 1/4 turn. Tighten jam nut. 6.1.4. CUSHION VALVE ADJUSTMENT To control the speed of the mover, the adjustable needle valve (Figure 6.3) can be: • screwed in for increased speed (adjust by 1/8 turn increments) • screwed out for decreased speed (adjust by 1/8 turn increments) Figure 6.
6. MAINTENANCE & STORAGE 6.2.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 7. TROUBLESHOOTING 7. Troubleshooting PROBLEM Valve is leaking. Machine operates slowly.
7.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 8. APPENDIX 8.1. BOLT TORQUE VALUES 8. Appendix 8.1. BOLT TORQUE VALUES The tables shown below give correct torque values for various bolts and capscrews. Tighten all bolts to the torque specified in the chart unless otherwise noted. Check tightness of bolts periodically, using bolt torque chart as your guide. Replace hardware with the same strength bolt. Table 8.
8. APPENDIX 8.2. TIGHTENING O-RING FITTINGS WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS Table 8.2 Metric Bolt Torque BOLT DIAMETER M3 M4 M5 M6 M8 M10 M12 M14 M16 M20 M24 M30 M36 (Nm) 0.5 3 6 10 25 50 90 140 225 435 750 1495 2600 (Lb-ft) 0.4 2.2 4 7 18 37 66 103 166 321 553 1103 1917 (Nm) 1.8 4.5 9 15 35 70 125 200 310 610 1050 2100 3675 (Lb-ft) 1.3 3.3 7 11 26 52 92 148 229 450 774 1550 2710 8.2. TIGHTENING O-RING FITTINGS 1.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 8. APPENDIX 8.3. PARTS 8.3. PARTS 8.3.1.
8. APPENDIX 8.3. PARTS WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS Table 8.4 Item Part No.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 8. APPENDIX 8.3. PARTS Table 8.4 Item Part No.
8. APPENDIX 8.3. PARTS WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS Table 8.5 Item Part No.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 8. APPENDIX 8.3. PARTS 8.3.3. TANK UPGRADE KIT, 43 L Table 8.6 Item Part No.
8. APPENDIX 8.3. PARTS WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 8.3.4. IN-LINE HYDRAULIC OIL FILTER Table 8.7 60 Item Part No.
WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS 8. APPENDIX 8.3. PARTS 8.3.5. HYDRAULIC WINCH & CONTROL VALVE Table 8.8 Item Part No.
8. APPENDIX 8.3. PARTS WHEATHEART - SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS Table 8.8 Item Part No. 23 0601008 Description Washer Flat 3/8” Plt Qty 4 8.3.6. HYDRAULIC WINCH (DUTTON) & CONTROL Table 8.9 Item Part No. A B C D E F G H J K L M 0707001 0707003A 0700001B 9901001PRP 0707002 0700008 1600023 1600024 1600025 1600006 1600026 1600007 0700009 0700011 1600026B N 62 Description 2503 Winch Safety Bracket Motor Coupler w/Roll Pin Motor, Hyd 4.6 cu. In.
WARRANTY REGISTRATION Wheatheart congratulates you on your new equipment purchase. The warranty registration form must be filled out within thirty (30) days from delivery date and sent to: Wheatheart Manufacturing 3455 Idylwyld Dr. N., Saskatoon, Saskatchewan S7L 6B5 CUSTOMER COPY (Retain this card for warranty and record purposes.
LIMITED WARRANTY Wheatheart warrants to the buyer that the new machinery is free from defects in material and workmanship. This warranty is only effective for any new machinery that has not been altered, changed, repaired, or treated since its delivery to the buyer, other than by Wheatheart or its authorized dealers or employees, and does not apply to accessories, attachments, tools, or parts sold or operated with the new machinery if they have not been manufactured by Wheatheart.
Wheatheart is a Division of Ag Growth Industries LP Part of the Ag Growth International Inc. Group 3455 Idylwyld Drive North Saskatoon, Saskatchewan, Canada Phone: (306) 934-0611 Fax: (306) 934-6020 Toll Free: (877) 934-0649 (Canada & USA) website: www.wheatheart.com email: sales@wheatheart.
