TM SIMP HOME ® LIFE BY DESIG N TM DRAPER / BAXTER / TIERNEY MIDCENTURYWIDEBOOKCASEANDSTORAGEUNIT MODEL # AXCDRP41-WH 1/24
TM SIMP HOME ® LIFE BY DESIG N TM Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service at 1-866-518-0120 ext. 262 Monday to Friday between 9 am –4 pm EST or go to www.simpli-home.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
MODEL # AXCDRP41-WH PRE-ASSEMBLY INFORMATION PART DESCRIPTION AL B AR t Fron Front / vant Front / A LEFT SIDE QTY 1 C nt / Ava Avant TOP QTY 1 RIGHT SIDE QTY 1 E D vant t/A t Fron UpSdieVer/ctial Fron BOTTOM SHELF QTY 1 F CABINET SHELF QTY 2 CABINET SHELF QTY 1 DIVIDER QTY 3 G1 Warning Label TOP BACK PANEL QTY 1 ant / Av G2 MIDDLE BACK PANEL QTY 2 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
MODEL # AXCDRP41-WH PRE-ASSEMBLY INFORMATION PART DESCRIPTION G3 H1 BOTTOM BACK PANEL QTY 1 I H2 JL DRAWER FRONT QTY 2 JR LEFT DRAWER SIDE QTY 2 L K LEG (L&R Same) QTY 2 LEG (L&R Same) QTY 2 RIGHT DRAWER SIDE QTY 2 M Front / A DRAWER BACK QTY 2 DRAWER BOTTOM QTY 2 vant SMALL DIVIDER QTY 1 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
MODEL # AXCDRP41-WH PRE-ASSEMBLY INFORMATION HARDWARE DESCRIPTION 2 1 ALLEN KEY SCREW M6 X 30mm QTY 32 3 ALLENKEYBOLT:M8X60mm-QTY8 LOCKWASHER:Ø12/Ø8X1.5mm-QTY8 WASHER:Ø19/Ø8X1mm-QTY8 5 4 CAM LOCK PIN CAM LOCK QTY 38 SETS ALLEN KEY QTY 1 QTY8SETS 6 PHILLIPS SCREW ROUND HEAD M4 X 15mm QTY 26 PLASTIC CAP QTY 15 7 a.M4X25mm-QTY2 (1siextra) b.M4X15mm-QTY1 c.
MODEL # AXCDRP41-WH COMPONENTS-KEY DIAGRAM B Fron t/A UVcdaSp/elitr vant G1 D UVcdaSp/elitr F G2 AR D AL F UVcdaSp/elitr G2 D G3 Fron E t/A Fron vant t / Ava nt C M H1 H2 H2 H1 JR K L JL I 8/24
MODEL # AXCDRP41-WH ASSEMBLY STEP-1 I JR JL JR I JL 4 1. Attach four Cam Lock Pins 4 into pre-drilled holes at the back of Drawer Front I . 2. Align Cam Lock Pins with Drawer Sides's guide holes before attach the Cam Lock Pins into Drawer Sides JL , JR . 3. Insert two Cam Locks 4 into guide holes on each Drawer Side JL , JR . 4. Use flathead screwdriver to secure Cam Locks. Do not over-tighten. STEP-2 JR L I JL 1. Slide Drawer Bottom L firmly into slots on Drawer Sides JL , JR and Drawer Front I .
MODEL # AXCDRP41-WH ASSEMBLY STEP-3 JR K L I 1 JL 3 1. Align Drawer Back K with Drawer Bottom L and press firmly into slot. 2. Attach Drawer Back K using two Allen Key Screws 1 through guide holes on each Drawer Side JL , JR . 3. Use Allen Key 3 to tighten Screws. Do not over-tighten. Repeat Step 1 - 3 for the second drawer.
MODEL # AXCDRP41-WH ASSEMBLY STEP-4 1 3 UpSdieV/erctial D F UpSdieV/erctial D 4 1. Attach Divider D to Cabinet Shelf F using three Allen Key Screws 1 through guide holes from the Shelf F to pre-drilled holes of Divider D . 2. Use Allen Key 3 to tighten Screws. Do not over-tighten. 3. Attach three Cam Lock Pins 4 into pre-drilled holes at underneath of Cabinet Shelf F . 4. Align Cam Lock Pins with guide holes and attach Divider D . 5. Insert three Cam Locks 4 into guide holes on Divider D . 6.
MODEL # AXCDRP41-WH ASSEMBLY STEP-5 UpdSiVee/cairtl UpdSiVee/cairtl D F 1 3 1. Attach Cabinet Shelf F to Divider D using three Allen Key Screws 1 through guide holes from the Shelf F to pre-drilled holes of Divider D . 2. Use Allen Key 3 to tighten Screws. Do not over-tighten.
MODEL # AXCDRP41-WH ASSEMBLY STEP-6 4 UVcdaSp/elitr UVcdaSp/elitr D UVcdaSp/elitr D F 1. Attach three Cam Lock Pins 4 into pre-drilled holes at underneath of Cabinet Shelf F . 2. Align Cam Lock Pins with guide holes and attach Divider D . 3. Insert three Cam Locks 4 into guide holes on Divider D . 4. Use flathead screwdriver to secure Cam Locks. Do not over-tighten.
MODEL # AXCDRP41-WH ASSEMBLY STEP-7 1 3 UVcdaSp/elitr UVcdaSp/elitr UVcdaSp/elitr Front / Avant D E 1. Attach Cabinet Shelf E to Divider D using three Allen Key Screws 1 through guide holes from the Shelf E to pre-drilled holes of Divider D . 2. Use Allen Key 3 to tighten Screws. Do not over-tighten.
MODEL # AXCDRP41-WH ASSEMBLY STEP-8 UVcdaSp/elitr UVcdaSp/elitr D Front / Avant Front / Avant UVcdaSp/elitr E M 4 1. Attach three Cam Lock Pins 4 into pre-drilled holes at the underneath of Cabinet Shelf E . 2. Align Cam Lock Pins with guide holes from M and attach Small Divider M to Cabinet Shelf E . 3. Insert three Cam Locks 4 into guide holes on Small Divider M . 4. Use flathead screwdriver to secure Cam Locks. Do not over-tighten.
MODEL # AXCDRP41-WH ASSEMBLY STEP-9 4 AL Front / Avant lacitVer/deiSUp F lacitVer/deiSUp F Front / Avant Front / Avant lacitVer/deiSUp Front / Avant E AR 3 1 1. Attach twelve Cam Lock Pins 4 into pre-drilled holes on inside of Sides AL , AR (six Cam Lock Pins on each Side). 2. Align Cam Lock Pins with guide holes and attach Cabinet Shelf F . 3. Insert six Cam Locks 4 into guide holes on each Cabinet Shelf F . 4. Use flathead screwdriver to secure Cam Locks. Do not over-tighten. 5.
MODEL # AXCDRP41-WH ASSEMBLY STEP-10 M AL Front / Avant lacitVer/deiSUp lacitVer/deiSUp Front / Avant C Front / Avant Front / Avant lacitVer/deiSUp AR 1 3 3 1 1. Attach Bottom Shelf C to Sides AL , AR and Small Divider M using nine Allen Key Screws 1 through guide holes from the Shelf C to pre-drilled holes of Sides AL , AR and Small Divider M (three Screws on each Side and Small Divider) . 2. Use Allen Key 3 to tighten Screws. Do not over-tighten.
MODEL # AXCDRP41-WH ASSEMBLY STEP-11 2 3 lacitVer/deiSUp lacitVer/deiSUp lacitVer/deiSUp Front / Avant Front / Avant H1 C H2 H2 H1 1. Attach Legs H1 , H2 to Bottom Shelf C using eight sets Allen Key Bolts, Lock washers and Washers 2 through guide holes (two sets on each Leg). 2. Use Allen Key 3 to tighten Bolts. Do not over-tighten.
MODEL # AXCDRP41-WH ASSEMBLY STEP-12 4 AL B Front / Avant Front / Avant D Front / Avant 4 AR 1. Attach nine Cam Lock Pins 4 into pre-drilled holes at underneath of Top B . 2. Align Cam Lock Pins with guide holes from AL , AR , D and attach Divider D and Sides AL , AR to Top B . 3. Insert three Cam Locks 4 into guide holes on Divider D and six Cam Locks 4 into guide holes on Sides AL , AR . 4. Use flathead screwdriver to secure Cam Locks. Do not over-tighten.
MODEL # AXCDRP41-WH ASSEMBLY STEP-13 NOTE: The screwdriver is not included in the hardware pack. 5 B t Fron / Av ant G1 G2 Warning Label t Fron nt / Ava G2 G3 1. Use twenty one Phillips Screws Round Head 5 to attach Back Panels G1 , G2 , G3 through guide holes from Back Panels to the back of bookcase . 2. Use Phillips screwdriver to tighten screws. Do not over-tighten.
MODEL # AXCDRP41-WH ASSEMBLY STEP-14 6 D AL D AR D 1. Insert fifteen Plastic Caps 6 into holes Cam Locks on Sides AL , AR and Dividers D . 2. Insert assembly drawer into glides on assembly bookcase.
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP-15 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. x P 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. x 3. 4. 5. 6. 7. P Drill a 3/16 inch hole in the wall.
TM SIMP HOME ® LIFE BY DESIG N TM WARRANTY Thank you for purchasing a Simpli Home – Wyndenhall – Brooklyn + Max product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.) please contact us at our toll free service line at 1-866-518-0120 ext.
