SIMP HOME I ® I L I F E B Y D E S I GN CONNAUGHT / HAMPSHIRE / SOMERSET ENTRYWAY STORAGE BENCH MODEL # AXCCON-09-GR 1/14
SIMP HOME I I ® L I F E B Y D E S I GN Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service at 1-866-518-0120 ext. 262 Monday to Friday between 9 am – 4 pm EST or go to www.simpli-home.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION Identify all the parts and hardware. Do not discard of the packaging until you have checked that you have all of the parts and hardware required. Hardware package may have spare parts. WARNING: This item contains small parts which can be swallowed by children and pets. Keep children and pets away during assembly.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
MODEL # AXCCON-09-GR PRE-ASSEMBLY INFORMATION PARTS DESCRIPTION A BL SEAT QTY 1 LEFT SIDE QTY 1 D RIGHT SIDE QTY 1 E Up Side / Vertical C BR FRONT QTY 1 F BACK QTY 1 G BACKREST QTY 1 DIVIDER QTY 1 H BOTTOM PANEL QTY 1 BOTTOM SUPPORT LEG QTY 1 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION MODEL # AXCCON-09-GR HARDWARE DESCRIPTION 1 2 CAM LOCK PIN CAM LOCK QTY 4 SET ALLEN KEY SCREW M6 x 30 mm QTY 12 4 3 5 6 PHILLIPS SCREW ROUND HEAD M4 X 15 mm QTY 4 ALLEN KEY QTY 1 7 8 PHILLIPS SCREW M4 X 30 mm QTY 4 WOOD DOWEL 8 X 30 mm QTY 10 PHILLIPS SCREW M4 X 15 mm QTY 6 9 ALLEN KEY BOLT M6 x 50 mm QTY 4 LID SUPPORT QTY 1 10 WOOD BOLT CAP QTY 4 Required Flathead screwdriver Phillips screwdriver Rubber mallet Not Included NEED HELP? For help with assembly or
COMPONENTS – KEY DIAGRAM MODEL # AXCCON-09-GR BR BL 7/14
ASSEMBLY MODEL # AXCCON-09-GR Up Side / Vertical STEP 1 1. Attach 2 Cam Lock Pins 2 to Back D into guide holes. 2. Align and insert Cam Lock Pins on Back D into pre-drilled holes on Dividers E . ( Note: please pay close attention to the location of the 2 small guide holes which accommodate the lid support. They need to be on the same side as the holes of cross hinges ). 3. Place 2 Cam Locks 2 into pre-drilled holes on Dividers E . 4. Use a flathead screwdriver to tighten Cam Locks into Pins.
ASSEMBLY MODEL # AXCCON-09-GR Up Side / Vertical Up Side / Vertical STEP 2 1. Attach Bottom Panel G to Divider E & Back D by sliding on the gap between Divider E & the long rail on Back D .
ASSEMBLY MODEL # AXCCON-09-GR Up Side / Vertical STEP 3 1. Attach 2 Cam Lock Pins 2 to Front C into guide holes. 2. Align and insert Cam Lock Pins on Front C into pre-drilled holes on Dividers E . 3. Place 2 Cam Locks 2 into pre-drilled holes on Dividers E . 4. Use a flathead screwdriver to tighten Cam Locks into Pins.
ASSEMBLY MODEL # AXCCON-09-GR STEP 4 BL BR 1. Insert 5 Dowels 3 into each Side BL , BR at specified location. 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. ½ length of Dowels should be exposed. 3. Align pre-drilled holes on side bars of Front C & Back D and Backrest F with Dowel 3 on Sides BL , BR . 4. Attach Front C & Back D to Sides BL , BR using 12 Allen Key Screws 1 through predrilled holes ( 6 Screws / each Side BL , BR ). 5.
ASSEMBLY MODEL # AXCCON-09-GR STEP 5 NOTE: The screwdriver is not included in the hardware pack. 1. Attach Bottom Support Leg H into pre-drilled holes of Bottom Panel G using 4 Phillips Screws 7 . 2. Use Phillips screwdriver to tighten Screws. Do not over-tighten. STEP 6 BR BL 1. Attach Seat A to Back D using 6 Phillips Screws 6 ( using guide holes on bar of Back ). 2. Use phillips screwdriver to tighten Screws. Do not over-tighten.
ASSEMBLY MODEL # AXCCON-09-GR STEP 7 BL BR 1. Attach Lid Supports 9 into pre-drilled holes of Seat A and Divider E using Phillips Screws Round Head 5 . 2. Use phillips screwdriver to tighten Screws. Do not over-tighten. STEP 8 BR BL 1. Insert 4 Wood Bolt Caps 10 into exposed bolt holes on side of bench.
SIMP HOME I I ® L I F E B Y D E S I GN WARRANTY Thank you for purchasing a Simpli Home – Wyndenhall – Brooklyn + Max product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.
