TM SIMP HOME ® LIFE BY DESIG N TM BURLINGTON / PORTLAND / BERKSHIRE 72 INCH WIDE TV MEDIA STAND MODEL # AXCBUR72-GR 1/30
TM SIMP HOME ® LIFE BY DESIG N TM Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service at 1-866-518-0120 ext. 262 Monday to Friday between 9 am –4 pm EST or go to www.simpli-home.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION . PART DESCRIPTION A MODEL # AXCBUR72-GR . . BL BR Front Fron Front t / Avan / Avan t t/A vant TOP QTY 1 LEFT SIDE QTY 1 . RIGHT SIDE QTY 1 . . C E D Fron t/A Fron van t BOTTOM SHELF QTY 1 . F . GL Fron t/A van t TOP DIVIDER QTY 1 vant CENTRE SHELF QTY 1 TOP SHELF QTY 1 .
PRE-ASSEMBLY INFORMATION . PART DESCRIPTION HL Front MODEL # AXCBUR72-GR . . HR I Front t / Avan LEFT DIVIDER QTY 1 / Avan t RIGHT DIVIDER QTY 1 . SHELF QTY 2 . . J LL K LARGE DOOR (L&R Same) QTY 2 . . LR LEFT BACK PANEL QTY 1 SMALL DOOR (L&R Same) QTY 2 . L1 L2 Warning Label RIGHT BACK PANEL QTY 1 TOP BACK PANEL QTY 1 BOTTOM BACK PANEL QTY 1 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION . PART DESCRIPTION M . . N BOTTOM SUPPORT LEG QTY 2 . O FLIP DOWN DOOR QTY 1 Q PR LEFT DRAWER SIDE QTY 1 DRAWER FRONT QTY 1 . . PL MODEL # AXCBUR72-GR RIGHT DRAWER SIDE QTY 1 DRAWER BACK QTY 1 . R DRAWER BOTTOM QTY 1 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION . HARDWARE DESCRIPTION 1 2 . . 3 . 5 PHILLIPS SCREW ROUND HEAD M4 X 15mm QTY 29 . 7 . . PHILLIPS SCREW M3 X 15mm QTY 16 12 PHILLIPS SCREW M3.5 X 15mm QTY 12 HINGE QTY 2 LATCH QTY 1 SET . 14 PHILLIPS SCREW M3 X 12mm QTY 28 MAGNET AND PLATE QTY 4 SETS . 11 . 13 8 HANDLE M4 X 12 mm QTY 2 SETS 10 . ALLEN KEY QTY 1 . SHELF SUPPORT QTY 12 9 4 WOOD DOWEL Ø8 X 30mm QTY 28 6 . . CAM LOCK PIN CAM LOCK QTY 22 SETS ALLEN KEY SCREW M6 X 30mm QTY 34 .
COMPONENTS-KEY DIAGRAM MODEL # AXCBUR72-GR A Front / Avan t LL L1 LR Front / Front F L2 / Ava nt t E I HL J K GL Front Avan t Front Front / Avan t BR HR t / Avan t K N GR / Avan I D Avan t / Avan BL Front / Front Front J / Avan t C M M PR Q R PL O 9/30
ASSEMBLY MODEL # AXCBUR72-GR STEP-1 P X 2 2 O 2 1. Attach four Cam Lock Pins 2 into pre-drilled holes on back of Drawer Front O . 2. Use Phillips screwdriver to secure Cam Lock Pins. Do not over-tighten. STEP-2 O PR PR O PL PL 2 2 O PR 2 PL 1.AlignCamLockPinswithguideholesandattachDrawerSides 2.InserttwoCamLocks2intoguideholesoneachDrawerSide 3.UsePhilpsscrewdrivertosecureCamLocks.Donotover-tighten. PL ,PR toDrawerFrontO. PL , PR .
ASSEMBLY MODEL # AXCBUR72-GR STEP-3 O PR O PR R PL R PL 1.SlideDrawerBottomRfirmlyintoslotsonDrawerSidesPL,PRandDrawerFrontO. STEP-4 O PR O PR R Q PL Q PL 1 4 1. Align Drawer Back Q with Drawer Bottom R and press firmly into slot . 2. Attach Drawer Back using two Allen Key Screws 1 through drilled holes on each Drawer Side PL , PR . 3. Use Allen Key 4 to tighten Screws. Do not over-tighten STEP-5 7 O 1. Use Phillips screwdriver to attach Handle 7 to Drawer Front O .
ASSEMBLY MODEL # AXCBUR72-GR STEP-6 Front E / Avan t 11 3 10 3 1. Insert six Dowels 3 into guide holes on Centre Shelf E . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. 1/2 length of Dowels should be exposed. 3. Attach Hinge 10 to Centre Shelf E using Phillips Screws 11 to attach Centre Shelf E through guide holes. 4. Use Phillips Screwdriver to tighten screws. Do not over-tighten. STEP-7 GR GL ant t / Av Fron Fron t / Av ant 3 3 1.
ASSEMBLY MODEL # AXCBUR72-GR STEP-8 GR Front / Avant Front / Avant E Front / Avant GL GR Front / Avant 1. Align Wood Dowels with guide holes and attach Centre Shelf E to Dividers GL , GR . Front / Avant GL E STEP-9 F 3 Fron t / Av ant 3 1. Insert two Dowels 3 into guide holes on Top Divider F . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. 1/2 length of Dowels should be exposed.
ASSEMBLY MODEL # AXCBUR72-GR STEP-10 P X 2 2 3 2 D 3 3 1. Insert four Dowels 3 into guide holes on Top Shelf D . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. 1/2 length of Dowels should be exposed. 3. Attach six Cam Lock Pins 2 into pre-drilled holes on Top Shelf D . 4. Use Phillips screwdriver to secure Cam Lock Pins. Do not over-tighten. F Front / Avant Front / Avant STEP-11 D 1. Align Wood Dowels with guide holes on Top Shelf D attach Top Divider F to Top Shelf D .
ASSEMBLY MODEL # AXCBUR72-GR STEP-12 Front / Avant Front / Avant Front / Avant Front / Avant D GR GL 1. Align Cam Lock Pin with guide holes on Middle Dividers GL , GR and attach Middle Dividers GL , GR to Top Shelf D . Front / Avant D Front / Avant 2 GR GL 2. Insert six Cam Locks 2 into guide holes on Middle Dividers GL , GR (3 Cam Locks on each Middle Divider). 3. Use Philpsscrewdriver to secure Cam Locks.
ASSEMBLY MODEL # AXCBUR72-GR STEP-13 P X 2 2 2 3 HL t Fron HR Fron ant / Av t/A vant 3 1. Insert two Dowels 3 into guide holes on each Divider HL , HR . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. 1/2 length of Dowels should be exposed. 3. Attach three Cam Lock Pins 2 into pre-drilled holes on each Divider HL , HR . 4. Use Phillips screwdriver to secure Cam Lock Pins. Do not over-tighten. STEP-14 3 Fron t / Av C 3 ant 3 1.
ASSEMBLY MODEL # AXCBUR72-GR STEP-15 Front / Avant Front / Avant HR Front / Avant D GR GL Front / Avant HL Front / Avant HR D Front / Avant HL Front / Avant 2 Front / Avant 1. Align Wood Dowels and Cam Lock Pins with guide holes on Top Shelf D and attach Dividers HL , HR to Top Shelf D . GR GL 2. Insert six Cam Locks 2 into guide holes on Top Shelf D . 3. Use Philpsscrewdriver to secure Cam Locks.
ASSEMBLY MODEL # AXCBUR72-GR STEP-16 HR Front / Avant Front / Avant Front / Avant Front / Avant HL Front / Avant GL GR C 1. Align Wood Dowels with guide holes on Bottom Shelf C and attach parts HL , HR , GL , GR to Bottom Shelf C . HR GR 1 Front / Avant Front / Avant GL HL 1 1 C 1 1 4 2. Use three Allen Key Screws 1 to attach each part HL , HR , GL , GR through guide holes from Bottom Shelf C to pre-drilled holes of parts HL , HR , GL , GR . 3.
ASSEMBLY MODEL # AXCBUR72-GR STEP-17 P X 2 2 BL Fron t/A 3 van t 3 2 BR t Fron / Av ant 3 1. Insert two Dowels 3 into guide holes on each Side BL , BR . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. 1/2 length of Dowels should be exposed. 3. Attach three Cam Lock Pins 2 into pre-drilled holes on each Side BL , BR . 4. Use Phillips screwdriver to secure Cam Lock Pins. Do not over-tighten.
ASSEMBLY MODEL # AXCBUR72-GR STEP-18 Front / Avant BR C Front / Avant Front / Avant Front / Avant BL BR Front / Avant 1. Align Wood Dowels and Cam Lock Pins with guide holes on Bottom Shelf C and attach Sides BL , BR to Bottom Shelf C . C Front / Avant Front / Avant Front / Avant BL 2 2. Insert six Cam Locks 2 into guide holes on Bottom Shelf C . 3. Use Philpsscrewdriver to secure Cam Locks.
ASSEMBLY MODEL # AXCBUR72-GR HR Front / Avant A BR HL Front / Avant F Front / Avant Front / Avant Front / Avant STEP-19 BL 1. Align Wood Dowels with guide holes on Top A and attach parts BL , BR , HL , HR , F to Top A . 1 BR F HR A 4 HL Front / Avant Front / Avant Front / Avant 1 4 BL 2. Use three Allen Key Screws 1 to attach each part BL , BR , HL , HR , F through guide holes each part BL , BR , HL , HR , F to pre-drilled holes of Top A . 3. Use Allen Key 4 to tighten Screws.
ASSEMBLY MODEL # AXCBUR72-GR STEP-20 BR BL Front / Avant Front / Avant A C M M 14 1. Align two Bottom Support Legs M with pre-drilled holes on back of Bottom Shelf C . Use Phillips Screwdriver to tighten four Phillips Screws 14 .
ASSEMBLY MODEL # AXCBUR72-GR STEP-21 Warning Label Front / Avant L1 Front / LR Avant LL L2 Note: Thebackofthetvframedoesnothavepre-driledholestoattachthebackpanels. Front / L1 Front / Avant LL Avant LR L2 5 1. Attach the Back Panels LL , LR , L1 , L2 to back frame using Phillips Screws Round Head 5 through guide holes from Back Panels. 2. Use Phillips Screwdriver to tighten screws. Do not over-tighten.
ASSEMBLY MODEL # AXCBUR72-GR STEP-22 First Step Last Step ( after adjust the door ) 13 13 BR HL E J HR K BL J N K 11 10 1.AttachhingesonDoorsJ,KtoSidesBL,BRandDividersHL,HR usingPhilpsScrews13intopre-drilholes: - UsingPhilpsscrewdrivertoattachScrews13atmiddleholeofhingesfor bothtop&bottomhinges. -Adjustthedoortoensuretheyarealignedstraight&squarewithbottomshelf&side. -UsingPhilpsscrewdrivertotightentherestofscrews13intopre-drilholes (top&bottomholesonhinges). 2.
ASSEMBLY MODEL # AXCBUR72-GR STEP-23 13 12 13 7 7 K J C J 9 K N GR 8 9 8 1.AttachMagnetPlates8tobottomcornerofDoorsJ,K usingPhilpsScrews9intopre-driledholesonDoorsJ,K. 2.AttachMagnets8usingPhilpsScrews9intopre-driledholesBottomShelfC. 3.AttachLatch12toFlipDownDoorNusingPhilpsScrews13intopre-driledholes. 4.AttachLatch12toRightMiddleDivider GR usingPhilpsScrews13intopre-driledholes. 5.UsePhilpsscrewdrivertosnuglytightenscrew. 6. UsePhilpsscrewdrivertoattachHandle7toFlipDownDoorN.
ASSEMBLY MODEL # AXCBUR72-GR STEP-24 shelf level 1 shelf support anti - tipping shelf level 2 shelf level 3 6 6 I I I I 1.UsefourShelfSupports6foreachCabinetShelfIindesiredlocation. 2.TwoShelfSupports6maybeusedonbacktopofeachCabinetShelfIasa tippingrestraint .
ASSEMBLY MODEL # AXCBUR72-GR STEP-25 P X 1. Insert assembled drawer into glides on assembled TV.
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP-26 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. x P 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. x 3. 4. 5. 6. 7. P Drill a 3/16 inch hole in the wall.
TM SIMP HOME ® LIFE BY DESIG N TM WARRANTY Thank you for purchasing a Simpli Home – Wyndenhall – Brooklyn + Max product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.) please contact us at our toll free service line at 1-866-518-0120 ext.
