SIMP HOME I ® I L I F E B Y D E S I GN BURLINGTON / PORTLAND / BERKSHIRE TALL TV MEDIA STAND MODEL # AXCBUR17-RNAB 1/21
SIMP HOME I I ® L I F E B Y D E S I GN Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service at 1-866-518-0120 ext. 262 Monday to Friday between 9 am – 4 pm EST or go to www.simpli-home.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION MODEL # AXCBUR17-RNAB PARTS DESCRIPTION A BL BR Fron t/A van t Fron t / Av ant vant t/A Fron TOP QTY 1 C LEFT SIDE QTY 1 DL RIGHT SIDE QTY 1 DR Fron t/A van t Fron t / Av ant vant t/A Fron BOTTOM SHELF QTY 1 E LEFT DIVIDER QTY 1 F CENTRE SHELF QTY 1 H G CABINET SHELF QTY 4 CABINET SHELF QTY 1 I BACK PANEL QTY 1 RIGHT DIVIDER QTY 1 JL BACK PANEL QTY 1 LEFT BACK PANEL QTY 1 NEED HELP? For help with assembly or if you are missing a part, Please call cust
PRE-ASSEMBLY INFORMATION MODEL # AXCBUR17-RNAB PARTS DESCRIPTION JR Warning Label KL RIGHT BACK PANEL QTY 1 L KR LEFT DOOR QTY 1 ML MR LEFT DRAWER SIDE QTY 2 DRAWER FRONT QTY 2 N O DRAWER BACK QTY 2 RIGHT DOOR QTY 1 RIGHT DRAWER SIDE QTY 2 P DRAWER BOTTOM QTY 2 BOTTOM SUPPORT LEG QTY 1 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION MODEL # AXCBUR17-RNAB HARDWARE DESCRIPTION 1 3 2 ALLEN KEY SCREW M6 X 30 mm QTY 20 4 CAM LOCK PIN CAM LOCK QTY 26 SETS 6 5 ALLEN KEY QTY 1 7 PHILLIPS SCREW ROUND HEAD M4 X 15 mm QTY 27 SHELF SUPPORT QTY 30 9 8 PHILLIPS SCREW M3 X 12 mm QTY 12 10 WOOD DOWEL Ø8 X 30 mm QTY 8 PHILLIPS SCREW M3 X 15 mm QTY 8 11 MAGNET AND PLATE QTY 2 SETS 12 a. M4 X 25 - QTY 2 ( 1 is extra ) HANDLE M4 x 12 mm QTY 2 SETS PHILLIPS SCREW M4 X 30 mm QTY 4 b. M4 X 15 - QTY 1 c.
COMPONENTS – KEY DIAGRAM MODEL # AXCBUR17-RNAB Fron t / Av ant A JL H JR BR DR DL F G E BL G KL Fron t / Av ant G KR G I Fron t / Av ant Fron t / Av ant Fron t / Av ant Fron t / Av ant C P MR N ML O L 8/21
ASSEMBLY MODEL # AXCBUR17-RNAB STEP 1 L MR ML MR ML L 2 1. Attach four Cam Lock Pins 2 to back of Drawer Front L . 2. Align Cam Lock Pins with guide holes and attach Drawer Sides ML , MR . 3. Insert two Cam Locks 2 into guide holes on each Drawer Side ML , MR . 4. Use flathead screwdriver to secure Cam Locks. STEP 2 MR O L ML 1. Slide Drawer Bottom O firmly into slots on Drawer Sides ML , MR and Drawer Front L .
ASSEMBLY MODEL # AXCBUR17-RNAB STEP 3 N MR 1 O L ML 4 1. Align Drawer Back N with Drawer Bottom O and press firmly into slot . 2. Attach Drawer Back N using two Allen Key Screws 1 through guide holes on each side ML , MR . 3. Use Allen key 4 to tighten. Do not over-tighten. 10 STEP 4 NOTE: The screwdriver is not included in the hardware pack. L 1. Use Phillips Screwdriver to attach Handle 10 to Drawer Front L . Repeat Step 1-4 for the second drawer.
ASSEMBLY MODEL # AXCBUR17-RNAB STEP 5 Front / Avant DR E Front / Avant DL 2 1. Attach three Cam Lock Pins 2 into pre-drilled holes on each Divider DL , DR . 2. Align Cam Lock Pins with guide holes and attach Centre Shelf E . 3. Insert six Cam Locks 2 into guide holes on Centre Shelf E . 4. Use a flathead screwdriver to tighten Cam Locks. Do not over-tighten. STEP 6 Front / Avant E Front / Avant DL Front / Avant DR 1 C 4 1.
ASSEMBLY MODEL # AXCBUR17-RNAB BR Front / Avant BL Front / Avant DL Front / Avant E Front / Avant DR Front / Avant STEP 7 C 3 2 1. Insert four Dowels 3 into guide holes on Bottom Shelf C . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. 1/2 length of Dowels should be exposed. 3. Attach three Cam Lock Pins 2 into pre-drilled holes on each Side BL , BR . 4. Align Dowels 3 with guide holes of Sides BL , BR . 5. Align Cam Lock Pins with guide holes and attach Bottom Shelf C .
ASSEMBLY MODEL # AXCBUR17-RNAB STEP 8 3 2 1 Front / Avant BL Front / Avant Front / Avant C Front / Avant DL BR DR Front / Avant A Front / Avant 4 1. Insert two Dowels 3 into guide holes at top corners of each Side BL , BR . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. 1/2 length of Dowels should be exposed. 3. Attach six Cam Lock Pins 2 into pre-drilled holes at the bottom of Top A . 4. Align Cam Lock Pins with guide holes and attach Sides BL , BR . 5.
ASSEMBLY MODEL # AXCBUR17-RNAB A Front / Avant BL Front / Avant Front / Avant BR Front / Avant STEP 9 P C P 11 1. A ach Bo om Support Leg P align with pre-drilled holes at back of Bo om Shelf C . Use Phillips screwdriver to ghten four Phillips Screws 11 .
ASSEMBLY MODEL # AXCBUR17-RNAB STEP 10 Note: The back of the TV frame does not have pre-drilled holes to attach the back panels. Warning Label Fron t/A vant A H Fron t/A vant JL JR I 5 1. Use Phillips Screws Round Head 5 to attach Back Panels H I JL JR through guide holes from Back Panels to the back of TV Stand. 2. Use Phillips screwdriver to tighten screws. Do not over-tighten.
ASSEMBLY STEP 11 MODEL # AXCBUR17-RNAB Last Step ( after adjust the door ) First Step 7 7 7 A KR E 9 BR 8 C BL 9 8 KL 1. Attach hinges on Doors KL , KR to Sides BL , BR using Phillips Screws 7 into pre-drill holes: - Using Phillips screwdriver to attach Screws 7 at middle hole of hinges for both top & bottom hinges. - Adjust the door to ensure they are aligned straight & square with bottom shelf & side.
ASSEMBLY MODEL # AXCBUR17-RNAB STEP 12 shelf level 1 shelf support anti - tipping shelf level 2 6 shelf level 3 F G G 6 G G 1. Use four Shelf Supports 6 for each Shelf F , G in desired location . 2. Two Shelf Supports 6 may be used on back top of each Shelf F , G as a tipping restraint.
ASSEMBLY MODEL # AXCBUR17-RNAB STEP 13 1.
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP 14 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. x 3. 4. 5. 6. 7. Drill a 3/16 inch hole in the wall.
SIMP HOME I I ® L I F E B Y D E S I GN WARRANTY Thank you for purchasing a Simpli Home – Wyndenhall – Brooklyn + Max product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.
