TM SIMP HOME ® LIFE BY DESIG N TM GATSBY / MARSHAL / BROCKTON SPACE SAVER CABINET MODEL # AXCBCGAT-07 1/25
TM SIMP HOME ® LIFE BY DESIG N TM Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service at 1-866-518-0120 ext. 262 Monday to Friday between 9 am –4 pm EST or go to www.simpli-home.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION . PART DESCRIPTION A MODEL # AXCBCGAT-07 . . BL BR Fron t/A vant t/A Fron vant vant t/A Fron TOP QTY 1 TOP LEFT SIDE QTY 1 . . CL TOP RIGHT SIDE QTY 1 . CR D Fron nt va t/A t/A Fron Fron vant t/A t/A Fron BOTTOM LEFT SIDE QTY 1 . van t BOTTOM RIGHT SIDE QTY 1 . E MIDDLE SHELF QTY 1 .
PRE-ASSEMBLY INFORMATION . PART DESCRIPTION H . . I BOTTOM BAR QTY 1 . MODEL # AXCBCGAT-07 IL BOTTOM BACK PANEL QTY 1 LEFT BACK PANEL QTY 1 . IR J RIGHT BACK PANEL QTY 1 SHELF QTY 2 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION . HARDWARE DESCRIPTION 1 2 . CAM LOCK PIN CAM LOCK QTY 20 SETS . MODEL # AXCBCGAT-07 . 3 WOOD DOWEL Ø8 X 30mm QTY 13 . 5 . QTY 2 . . 8 . 11 PHILLIPS SCREW M3 X 15mm QTY 24 PHILLIPS SCREW M4 X 50mm QTY 2 SHELF SUPPORT QTY 8 . 10 PHILLIPS SCREW M4 X 15mm QTY 8 MAGNET AND PLATE QTY 2 SETS 7 HANDLE M4 X 25 mm QTY 2 SETS BRACKET 9 4 HINGE QTY 4 6 . . 12 PHILLIPS SCREW ROUND HEAD M4 X 15mm QTY 23 M a.4X25mmQ - TY2 1(siextra) M b.4X15mmQ - TY1 M c.
COMPONENTS-KEY DIAGRAM MODEL # AXCBCGAT-07 A Fron Fron t / Av ant Fron t/A vant t / Ava Fron IL IR t / Ava nt BL nt Fron t / Av ant J J BR F G G D I Fron t / Ava Fron t / Ava nt nt Fron t/A E CL vant CR H 8/25
ASSEMBLY MODEL # AXCBCGAT-07 STEP-1 t Fron ant / Av F 10 2 4 2 10 1.AttachMagnet4usingPhilpsScrews10intopre-driledholesonpartF. 2. Use Phillips screwdriver to secure Screws. Do not over-tighten. 3. Insert one Dowel 2 into guide holes on part F . 4. Use rubber mallet to tap Dowel 2 into bottom of holes securely. 1/2 length of Dowels should be exposed.
ASSEMBLY MODEL # AXCBCGAT-07 P STEP-2 X 1 1 1 BL vant t/A 1 Fron 1 BR vant t/A Fron 2 1 A 2 Fron t/A vant 2 1. Attach Cam Lock Pins 1 into pre-drilled holes on each part A , BL , BR . 2. Use Phillips screwdriver to secure Cam Lock Pins. Do not over-tighten. 3. Insert four Dowels 2 into guide holes on part A . 4. Use rubber mallet to tap Dowels 2 into bottom of holes securely. 1/2 length of Dowels should be exposed.
ASSEMBLY MODEL # AXCBCGAT-07 Front / Avant STEP-3 F D 8 8 1. Align Wood Dowel with guide hole on part D and attach part F to part D . 2.InserttwoPhilpsScrews8into guide holesonpartD. 3. Use Phillips screwdriver to secure Screws.
ASSEMBLY MODEL # AXCBCGAT-07 Front / Avant A Front / Avant STEP-4 F D 1. Align Cam Lock Pins with guide holes on part F and attach part A to part F . 1 Front / Avant A Front / Avant 1 F D 2. Insert two Cam Locks 1 into guide holes on part F . 3. Use Phillips screwdriver to secure Cam Locks.
ASSEMBLY MODEL # AXCBCGAT-07 STEP-5 Front / Avant Front / Avant F Front / Avant BL A D 1. Align Wood Dowels and Cam Lock Pins with guide holes and attach parts A , D to part BL . 1 1 F Front / Avant Front / Avant BL Front / Avant 1 A D 2. Insert Cam Locks 1 into guide holes on parts A , D . 3. Use Phillips screwdriver to secure Cam Locks.
ASSEMBLY MODEL # AXCBCGAT-07 Front / Avant STEP-6 A Front / Avant Front / Avant BR F D Front / Avant BL Front / Avant Front / Avant A BR 1 F BL D 1. Repeat Step-5 for the Right Side BR .
ASSEMBLY MODEL # AXCBCGAT-07 P STEP-7 X 1 1 1 CL 2 1 ant Av nt / Fro 1 2 1 CR 2 2 vant t/A Fron 1 2 H 2 2 1. Attach five Cam Lock Pins 1 into pre-drilled holes on each part CL , CR . 2. Use Phillips screwdriver to secure Cam Lock Pins. Do not over-tighten. 3. Insert Dowels 2 into guide holes on parts H , CL , CR . 4. Use rubber mallet to tap Dowels 2 into bottom of holes securely. 1/2 length of Dowels should be exposed.
ASSEMBLY MODEL # AXCBCGAT-07 Front / Avant Front / Avant STEP-8 E CL H 1. Align Wood Dowels and Cam Lock Pins with guide holes and attach parts E , H to part CL . 1 1 E CL H 2. Insert Cam Locks 1 into guide holes on parts E , H . 3. Use Phillips screwdriver to secure Cam Locks.
ASSEMBLY MODEL # AXCBCGAT-07 STEP-9 Front / Avant E Front / Avant CR H CL 1 E CR H CL 1. Repeat Step-8 for the Bottom Right Side CR .
ASSEMBLY MODEL # AXCBCGAT-07 STEP-10 1 1 ant t / Av Fron 5 t/ Fron t nt / Ava Fron t Avan 9 ant Front / Av Front / Av ant ant Front / Av ant Front / Av Front / Av ant vant Front / A ant Front / Av ant Front / Av ant Front / Av ant Front / Av ant Front / Av 1. Align Wood Dowels and Cam Lock Pins with guide holes on top fame and attach top frame to bottom frame. 2. Insert four Cam Locks 1 into guide holes on top fame . 3.
ASSEMBLY MODEL # AXCBCGAT-07 STEP-11 Note: Thebackofthecabinetframedoesnothavepre-driledholestoattachthebackpanels. ant Front / Av Warning Label ant Front / Av IL IL IR IR I I ant Front / Av Front / Av Fron t / Avant ant ant Front / Av 11 1. Attach the Back Panels I , IL , IR to back frame using Phillips Screws Round Head 11 through guide holes from Back Panels. 2. Use Phillips Screwdriver to tighten screws. Do not over-tighten.
ASSEMBLY MODEL # AXCBCGAT-07 STEP-12 7 t Fron / Av ant J J 1. Use four Shelf Supports 7 for each Shelf J in desired location .
ASSEMBLY MODEL # AXCBCGAT-07 STEP-13 3 4 10 10 G G 6 6 1.AttachHinge3toDoorsGusingPhilpsScrews10intopre-driledholesonDoorG. 2.AttachMagnetPlates4totopcornerofDoorsGusingPhilpsScrews10into pre-driledholesonDoorsG. 3. UsePhilpsscrewdrivertoattachHandle6toDoorsG.
ASSEMBLY MODEL # AXCBCGAT-07 STEP-14 BL G BR G 10 1.AttachHingeonDoorsHtoSidesBL,BR usingPhilpsScrews10intopre-driledholesonSidesBL,BR. 2. Use Phillips screwdriver to secure screws. Do not over-tighten.
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP-15 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. x P 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. x 3. 4. 5. 6. 7. P Drill a 3/16 inch hole in the wall.
TM SIMP HOME ® LIFE BY DESIG N TM WARRANTY Thank you for purchasing a Simpli Home – Wyndenhall – Brooklyn + Max product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.) please contact us at our toll free service line at 1-866-518-0120 ext.
