TM SIMP HOME ® LIFE BY DESIG N TM REDMOND / MANSFIELD / STANWICK TALL TV MEDIA STAND MODEL # AXCADM-06GR 1/19
TM SIMP HOME ® LIFE BY DESIG N TM Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service at 1-866-518-0120 ext. 262 Monday to Friday between 9 am –4 pm EST or go to www.simpli-home.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION PART DESCRIPTION AL MODEL # AXCADM-06GR B AR Fron Front / t / Avan Front LEFT SIDE QTY 1 C ant t / Av Avan t RIGHT SIDE QTY 1 DL TOP QTY 1 DR ant t / Av Fron Front BOTTOM SHELF QTY 1 E Front t / Avan LEFT DIVIDER QTY 1 F / Avan t RIGHT DIVIDER QTY 1 G1 Warning Label DOOR (L&R Same) QTY 2 CABINET SHELF QTY 2 TOP BACK PANEL QTY 1 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION PART DESCRIPTION G2 H BOTTOM BACK PANEL QTY 1 JL MODEL # AXCADM-06GR I TOP SHELF QTY 1 JR LEFT DRAWER SIDE QTY 2 DRAWER FRONT QTY 2 K RIGHT DRAWER SIDE QTY 2 DRAWER BACK QTY 2 M L DRAWER BOTTOM QTY 2 MIDDLE SHELF QTY 1 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION MODEL # AXCADM-06GR HARDWARE DESCRIPTION 2 1 ALLEN KEY SCREW M6 X 30mm QTY 26 3 ALLEN KEY QTY 1 5 4 6 PHILLIPS SCREW ROUND HEAD M4 X 15mm QTY 25 PHILLIPS SCREW M3 X 15mm QTY 8 PHILLIPS SCREW M3 X 12mm QTY 12 8 7 SHELF SUPPORT QTY 12 9 HANDLE M4 X 22mm QTY 2 SETS MAGNET AND PLATE QTY 2 SETS CAM LOCK PIN CAM LOCK QTY 26 SETS 11 10 HANDLE M4 X 10mm QTY 2 SETS a.M4X25mm-QTY2 (1siextra) b.M4X15mm-QTY1 c.
COMPONENTS-KEY DIAGRAM Fron t / Ava nt MODEL # AXCADM-06GR B G1 AL H DR M F AR F E Fron E DL G2 Fron t Fron t/A vant / Ava nt t / Av ant C K JR L I JL 8/19
ASSEMBLY MODEL # AXCADM-06GR STEP-1 JR JL I 9 1. Attach four Cam Lock Pins 9 to back of Drawer Front I . 2. Align Cam Lock Pins with pre-drilled holes and attach Drawer Sides JL , JR . 3. Insert two Cam Locks 9 into pre-drilled holes on each Drawer Side JL , JR . 4. Use flathead screwdriver to secure Cam Locks. STEP-2 JR L JL I 1. Slide Drawer Bottom L firmly into slots on Drawer Sides JL , JR and Drawer Front I .
ASSEMBLY MODEL # AXCADM-06GR STEP-3 K 1 JR L 2 JL 1. Align Drawer Back K with Drawer Bottom L and press firmly into slot. 2. Attach Drawer Back K using two Allen Key Screws 1 through pre-drilled holes on each Side JL , JR . 3. Use Allen Key 2 to tighten Screws. Do not over-tighten. STEP-4 10 NOTE: The screwdriver is not included in the hardware pack. I 1. Use phillips screwdriver to attach Handle 10 to Drawer Front I . Repeat Step 1 - 4 for the second drawer.
ASSEMBLY MODEL # AXCADM-06GR STEP-5 Front / Avant 9 DL Front / Avant M DR 1. Attach three Cam Lock Pins 9 to back of each Divider DL , DR . 2. Align Cam Lock Pins with pre-drilled holes and attach Middle Shelf M . 3. Insert six Cam Locks 9 into pre-drilled holes on Middle Shelf M . 4. Use flathead screwdriver to secure Cam Locks.
ASSEMBLY MODEL # AXCADM-06GR STEP-6 1 Front / Avant 2 9 DL Front / Avant Front / Avant Front / Avant H DR C 1. Attach six Cam Lock Pins 9 to underneath of Top Shelf H . 2. Align Cam Lock Pins with pre-drilled holes and attach Dividers DL , DR . 3. Insert three Cam Locks 9 into pre-drilled holes on each Divider DL , DR . 4. Use flathead screwdriver to secure Cam Locks. 5. Attach Bottom Shelf C to Dividers DL , DR using six Allen Key Screws 1 . (three screws on each Divider). 6.
ASSEMBLY MODEL # AXCADM-06GR STEP-7 9 AL Front / Avant H AR Front / Avant Front / Avant C 1 2 1. Attach three Cam Lock Pins 9 to back of each Side AL , AR . 2. Align Cam Lock Pins with pre-drilled holes and attach Top Shelf H . 3. Insert six Cam Locks 9 into pre-drilled holes on Top Shelf H . 4. Use flathead screwdriver to secure Cam Locks. 5. Attach Sides AL , AR to Bottom Shelf C using six Allen Key Screws 1 (three screws on each Side). 6. Use Allen Key 2 to tighten Screws. Do not over-tighten.
ASSEMBLY MODEL # AXCADM-06GR STEP-8 B Front / Avant Front / Avant Front / Avant AL AR 1 2 1. Attach Top B to Sides AL , AR using six Allen Key Screws 1 . (three screws on each Side). 2. Use Allen Key 2 to tighten Screws. Do not over-tighten. STEP-9 NOTE: The screwdriver is not included in the hardware pack. B vant Warning Label t/A Fron G1 6 G2 Front nt / Ava 1. Attach Back Panels G1 , G2 to back frame of TV Stand using twenty five Phillips Screws Round Head 6 through pre-drilled holes. 2.
ASSEMBLY MODEL # AXCADM-06GR STEP-10 NOTE: The screwdriver is not included in the hardware pack. 8 4 AL E DL t van t/A Fron t van t/A Fron t van t/A Fron AR DR t Fron ant / Av C t/ Fron n Ava t E t van t/A Fron 7 5 7 5 1. Attach hinges on Doors E to Sides AL , AR using Phillips Screws 4 into guide holes. 2. Attach Magnet Plates 7 to bottom corner of Doors E using Phillips Screws 5 into guide holes on Doors E . 3.
ASSEMBLY MODEL # AXCADM-06GR STEP-11 3 3 van t/A Fron t AL E F AR F E 3 F 1. Use four Shelf Supports 3 for each Cabinet Shelf F in desired location. 2. Two Shelf Supports 3 may be used on back top of each Cabinet Shelf F as a tipping restraint. 3. Insert assembled drawers into glides on assembled TV stand.
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP-12 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. x P 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. x 3. 4. 5. 6. 7. Drill a 3/16 inch hole in the wall.
TM SIMP HOME ® LIFE BY DESIG N TM WARRANTY Thank you for purchasing a Simpli Home – Wyndenhall – Brooklyn + Max product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.) please contact us at our toll free service line at 1-866-518-0120 ext.
