SIMP HOME I ® I L I F E B Y D E S I GN ACADIAN / NORMANDY / BRUNSWICK TALL TV MEDIA STAND MODEL # AXCACTTS-RNAB 1/20
SIMP HOME I I ® L I F E B Y D E S I GN Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service at 1-866-518-0120 ext. 262 Monday to Friday between 9 am – 4 pm EST or go to www.simpli-home.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION MODEL # AXCACTTS-RNAB PARTS DESCRIPTION A BL BR Fron t/A van t Fro nt/ Ava nt t van t/A Fron TOP QTY 1 C LEFT SIDE QTY 1 DL RIGHT SIDE QTY 1 DR Fro nt/ Ava nt Fro nt/ Ava nt t van t/A Fron LEFT DIVIDER QTY 1 BOTTOM SHELF QTY 1 E F LOWER CENTRE SHELF QTY 1 RIGHT DIVIDER QTY 1 G UPPER CENTRE SHELF QTY 1 CABINET SHELF QTY 4 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION MODEL # AXCACTTS-RNAB PARTS DESCRIPTION H I JL BACK PANEL QTY 1 JR Warning Label BACK PANEL QTY 1 K L RIGHT BACK PANEL QTY 1 ML LEFT BACK PANEL QTY 1 DOOR (L&R Same) QTY 2 MR N RIGHT DRAWER SIDE QTY 2 LEFT DRAWER SIDE QTY 2 DRAWER FRONT QTY 2 DRAWER BACK QTY 2 P O DRAWER BOTTOM QTY 2 BOTTOM SUPPORT LEG QTY 1 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION MODEL # AXCACTTS-RNAB HARDWARE DESCRIPTION 1 2 ALLEN KEY SCREW M6 X 30 mm QTY 26 4 3 CAM LOCK PIN CAM LOCK QTY 20 SETS 5 PHILLIPS SCREW ROUND HEAD M4 X 15 mm QTY 24 7 6 PHILLIPS SHORT SCREW M3 X 12 mm QTY 12 SHELF SUPPORT QTY 30 8 PHILLIPS MEDIUM SCREW M3 X 15 mm QTY 8 10 ALLEN KEY QTY 1 9 MAGNET and PLATE QTY 2 SETS 11 a. HANDLE M4 X 25 mm - QTY 2 M4 X 15 mm - QTY 2 QTY 4 SETS M4 X 25 - QTY 2 ( 1 is extra ) PHILLIPS SCREW M4 X 30 mm QTY 4 b.
COMPONENTS – KEY DIAGRAM MODEL # AXCACTTS-RNAB Fron t/A van t A JL H JR DR DL F E G Fron t/A vant G BR I BL K G G Fro nt / Ava nt Fron t/A vant Fro nt / Ava nt Fro nt / Ava nt C K P MR N ML O L 8/20
ASSEMBLY MODEL # AXCACTTS-RNAB STEP 1 L MR ML MR ML L 2 1. Attach 4 Cam Lock Pins 2 to back of Drawer Front L . 2. Align Cam Lock Pins with guide holes and attach Drawer Sides ML , MR . 3. Insert 2 Cam Locks 2 into guide holes on each Drawer Side ML , MR . 4. Use flathead screwdriver to secure Cam Locks. STEP 2 MR O ML L 1. Slide Drawer Bottom O firmly into slots on Drawer Sides ML , MR and Drawer Front L .
ASSEMBLY MODEL # AXCACTTS-RNAB STEP 3 N MR O 1 ML L 3 1. Align Drawer Back N with Drawer Bottom O and press firmly into slot . 2. Attach back using 2 Allen Key Screws 1 through guide holes on each side. 3. Use Allen key 3 to tighten. Do not over tighten. STEP 4 L NOTE: The screwdriver is not included in the hardware pack. 9 1. Use Phillips Screwdriver to attach Handle 9 to Drawer Front L . Repeat Step 1-4 for the second drawer.
ASSEMBLY MODEL # AXCACTTS-RNAB STEP 5 Front / Avant DR E Front / Avant DL 2 1. Attach 3 Cam Lock Pins 2 into pre-drilled holes on each Divider DL , DR . 2. Align Cam Lock Pins with guide holes and attach Lower Centre Shelf E . 3. Insert 6 Cam Locks 2 into guide holes on Lower Centre Shelf E . 4. Use flathead screwdriver to secure Cam Locks. STEP 6 Front / Avant DR Front / Avant DL 1 Front / Avant E C 3 1.
ASSEMBLY MODEL # AXCACTTS-RNAB Front / Avant STEP 7 BR Front / Avant Front / Avant DR E C BL Front / Avant Front / Avant DL 2 1. Attach 3 Cam Lock Pins 2 into pre-drilled on each Side BL , BR . 2. Align Cam Lock Pins with guide holes and attach Bottom Shelf C . 3. Insert 6 Cam Locks 2 into guide holes on Bottom Shelf C . 4. Use a flathead screwdriver to tighten Cam Locks into Pins.
ASSEMBLY MODEL # AXCACTTS-RNAB STEP 8 1 1 3 3 BL Front / Avant Front / Avant DR BR Front / Avant Front / Avant Front / Avant A DL C 1. Use 12 Allen Key Screws 1 attach Top A to Sides BL , BR and Dividers DL , DR . 2. Use Allen Key 3 to tighten screws. Do not over-tighten.
ASSEMBLY MODEL # AXCACTTS-RNAB STEP 9 BR A C BL 10 P 1. Attach Bottom Support Leg P to Bottom Shelf C using 4 Phillips Screws 10 . 2. Use Phillips screwdriver to tighten screws. Do not over-tighten. STEP 10 Note: The back of the tv frame does not have pre-drilled holes to attach the back panels. Warning Label 4 Fron t/A vant H Fron t / Av ant JL JR I 1. Attach Back Panels H I JL JR to back of TV Stand using Phillips Screws Round Head 4 through guide holes. 2.
ASSEMBLY MODEL # AXCACTTS-RNAB STEP 11 First Step Last Step ( after adjust the door ) 6 6 6 A BR K BL C K 7 8 8 7 9 1. Attach hinges on Doors K to Sides BL , BR using Phillips Screws 6 into pre-drill holes: - Using Phillips screwdriver to attach Screws 6 at middle hole of hinges for both top & bottom hinges. - Adjust the door to ensure they are aligned straight & square with bottom shelf & side.
ASSEMBLY MODEL # AXCACTTS-RNAB STEP 12 shelf level 1 shelf support anti - tipping shelf level 2 5 shelf level 3 G F 5 G G G 1. Use 4 Shelf Supports 5 for each Shelf F , G in desired location . 2. 2 Shelf Supports 5 may be used on back top of each Shelf F , G as a tipping restraint.
ASSEMBLY MODEL # AXCACTTS-RNAB STEP 13 1.
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP 14 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. x 3. 4. 5. 6. 7. Drill a 3/16 inch hole in the wall.
SIMP HOME I I ® L I F E B Y D E S I GN WARRANTY Thank you for purchasing a Simpli Home – Wyndenhall – Brooklyn + Max product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.
